Installation instructions downdraft raised vent models erv3015 and erv3615 part no. 107000 rev. D use these downdraft raised vents only with approved dacor ® appliances. See the installation instructions for the particular appliance model being installed to determine suitability. Includes installati...
Installation instructions .................................................. 10 installation preparation .................................................. 10 installing the raised vent in the cutout ..........................11 verifying proper operation ...............................................
1 important information about safety instructions • the important safety instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or oper- ating this or any other appliance. •...
2 important safety instructions • do not install or operate a damaged appliance. If you receive a damaged appliance, contact your dealer or builder. • observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. • the el...
3 product dimensions product specifications 15" (38.1 cm) 30" (76.2 cm) 20” (50.8 cm) 1 1/8” (2.9 cm) 28" 3 prong grounded power cord motor cover front of unit 6” (15.2 cm) 2 9/16” (6.5 cm) 9/16” (1.4 cm) 3” (7.6 cm) 1 15/16” (4.9 cm) b a 2 1/8” (5.4 cm) 2 3/16” (5.6 cm) 3/16” (5 mm) 5/16” (8 mm) th...
4 installation specifications planning the installation general system layout the vent system consists of the raised vent itself and a sin- gle dacor approved cabinet blower, remote blower or in-line blower (see facing page for examples). Warning • failure to install an approved blower or proper duc...
5 installation specifications example of layout with range and bottom exhaust example of layout with cabinet blower, exhaust through wall example of layout with cooktop and rear exhaust remp series remote blower 3 ¼” x 10” to round transition and 45° adjustable elbow duct work between raised vent an...
6 installation specifications installations with ilhsf and remp series blowers: with ilhsf and remp blowers, the raised vent can be configured to exhaust through the back, the bottom or either side by removing the appropriate exhaust knock-out shown on the facing page. • when connecting the duct wor...
7 duct installation requirements for all blowers: • all duct work materials (including screws and duct tape) must be purchased separately by the customer. • when planning new duct work, always look for the shortest, most direct route to the outside. See page 5 for examples. • you can increase the du...
8 installation specifications model a b c erv3015 12 1/8” (30.7 cm) 5 5/8” (14.4 cm) 1 3/4” (4.4 cm) erv3615 9 3/4” (24.8 cm) 8” (20.3 cm) 4 1/4” (10.8 cm) e rv adapter 8 7/8" (22.5 cm) from back of erv cutout to center line of cabp3 exhaust in any orientation bottom exhaust configuration shown duct...
9 installation specifications calculating the maximum duct run length • for optimal performance, consult a qualified hvac specialist when designing the duct system. • do not use duct work that is smaller in cross-sectional area than the required duct sizes in the tables below. • keep the duct run as...
10 installation preparation verify package contents 1. Unpack the raised vent and verify that all required parts have been provided. If any item is missing or damaged, please contact your dealer immediately. Do not install a damaged or incomplete appliance. The customer must report cosmetic issues w...
11 installing the raised vent in the cutout 1. Cut a hole in the cabinet to allow the duct work to pass through to the floor or wall for the planned duct system layout. Use the dimensions on pages 7 and 8 to determine the hole center line locations. If using the 2” x 16” to 3 1/4” x 10” transition (...
12 installation instructions cabinet blower installation if using cabinet blower (model cabp3): 1. Locate the wiring diagram label included with the adapter kit. Peel the protective backing off and place it over the existing label on the cabp3 blower as shown. 2. Locate the foam tape supplied with t...
13 installation instructions floor example of electrical installation with ilhsf or remp series blower (side view) remp16 remote blower connect wires/conduit according to remote blower installation instructions raised vent range wiring/conduit from raised vent to remote (or in-line) blower see raise...
14 installation instructions verifying proper operation warning • read the raised vent use and care manual completely before operation. • install all of the front filters prior to operating the raised vent. Refer to the use and care manual for filter instal- lation instructions. Caution to prevent d...
15 technical data stud chassis ground ground power input blower output gnd l2 n1 l1 n2 gnd com com no no up limit switch down limit switch com nc no nc nc remote pot snorkel switch com n no relay speed control red red blue blue red blk orng orn g blk yel yel wht l bl k wht wht ervxx15 raised vent wi...
16 notes.
17.
Dacor●14425clarkavenue,cityofindustry,ca91745●phone:(800)793-0093●fax:(626)403-3130●www.Dacor.Com.
