Installation instructions renaissance ® downdraft vent models erv3015, erv36-er, erv3615, erv48, erv48-er, prv30, prv36 and prv46 part no. 107736 rev. B use these downdraft vents only with approved dacor ® appliances. See the installation instructions for the particular appliance model being install...
Installation specifications ................................................ 6 planning the installation ................................................... 6 planning the duct work ................................................... 8 installation instructions .........................................
1 important information about safety instructions • the important safety instructions and warnings in these instructions are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or oper- ating this or any other appliance. •...
2 important safety instructions • do not install or operate a damaged appliance. If you receive a damaged appliance, contact your dealer or builder. • observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. • the el...
3 product dimensions - erv3015 and erv3615 product specifications 15" (38.1 cm) 30" (76.2 cm) 20” (50.8 cm) 1 1/8” (2.9 cm) 28" 3 prong grounded power cord motor cover front of unit 6” (15.2 cm) 2 9/16” (6.5 cm) 9/16” (1.4 cm) 3” (7.6 cm) 1 15/16” (4.9 cm) b a 2 1/8” (5.4 cm) 2 3/16” (5.6 cm) 3/16” ...
4 product specifications 30 1/4" (76.8 cm) to 37 1/4" (94.6 cm) 10" (25.4 cm) 30" (76.2 cm) 18 5/8” (47.3 cm) 5/16” (8 mm) thick stiffener across back 3 3/4" (9.5 cm) 1" (2.5 cm) 28" 3-prong grounded power cord vent shown in raised position product data label motor cover front of unit 6" (15.2 cm) 2...
5 product specifications product dimensions - erv36-er and erv48-er 30 1/4" (76.8 cm) to 37 1/4" (94.6 cm) 10" (25.4 cm) 30" (76.2 cm) 18 5/8” (47.3 cm) 5/16” (8 mm) thick stiffener across back 3 3/4" (9.5 cm) 1" (2.5 cm) 28" 3 prong grounded power cord vent shown in raised position product data lab...
6 installation specifications planning the installation general system layout the vent system consists of the downdraft vent itself and a single dacor approved cabinet blower (models erv3015 and erv3615), remote blower or in-line blower (see facing page for examples). Warning • failure to install an...
7 installation specifications example of layout with range and bottom exhaust example of layout with cabinet blower configuration, exhaust through wall example of layout with cooktop and rear exhaust remp series remote blower 3 ¼ x 10 to round transition and 45° adjustable elbow duct work between do...
8 installation specifications installations with ilhsf and remp series blowers: with ilhsf and remp blowers, the downdraft vent can be configured to exhaust through the back, the bottom or either side by removing the appropriate exhaust knock-out shown on the facing page. • when connecting the duct ...
9 duct installation requirements for all blowers: • all duct work materials (including screws and duct tape) must be purchased separately by the customer. • when planning new duct work, always look for the shortest, most direct route to the outside. See page 7 for examples. • you can increase the du...
10 installation specifications model a b c erv3015 12 1/8” (30.7 cm) 5 5/8” (14.4 cm) 1 3/4” (4.4 cm) erv3615 9 3/4” (24.8 cm) 8” (20.3 cm) 4 1/4” (10.8 cm) e rv adapter 8 7/8" (22.5 cm) from back of erv cutout to center line of cabp3 exhaust in any orientation bottom exhaust configuration shown duc...
11 installation specifications calculating the maximum duct run length • for optimal performance, consult a qualified hvac specialist when designing the duct system. • do not use duct work that is smaller in cross-sectional area than the required duct sizes in the tables below. • keep the duct run a...
12 installation preparation verify package contents 1. Unpack the unit and verify that all required parts have been provided. If any item is missing or damaged, please contact your dealer immediately. Do not install a damaged or incomplete appliance. The customer must report cosmetic issues within 3...
13 installing the downdraft vent in the cutout 1. Cut a hole in the cabinet to allow the duct work to pass through to the floor or wall for the planned duct system layout. Use the dimensions on pages 9 and 10 to determine the hole center line locations. If using the 2” x 16” to 3 1/4” x 10” transiti...
14 installation instructions cabinet blower installation: (optional, erv3015 and erv3615 only) 1. Locate the wiring diagram label included with the adapter kit. Peel the protective backing off and place it over the existing label on the cabp3 blower as shown. 2. Locate the foam tape supplied with th...
15 installation instructions floor example of electrical installation with ilhsf or remp series blower (side view) remp16 remote blower connect wires/conduit according to remote blower installation instructions downdraft vent range wiring/conduit from downdraft vent to remote (or in-line) blower see...
16 installation instructions verifying proper operation warning • read the downdraft vent use and care manual com- pletely before operation. • install all of the front filters prior to operating the downdraft vent. Refer to the use and care manual for filter installation instructions. Caution to pre...
17 technical data stud chassis ground ground power input blower output gnd l2 n1 l1 n2 gnd com com no no up limit switch down limit switch com nc no nc nc remote pot snorkel switch com n no relay speed control red red blue blue red blk orng orn g blk yel yel wht l bl k wht wht wiring diagram - all m...
Dacor●14425clarkavenue,cityofindustry,ca91745●phone:(800)793-0093●fax:(626)403-3130●www.Dacor.Com.
