Dacor Millennia ETT304-1 Installation Instructions Manual - page 4
3
Below Countertop Preparation
wARNINg:
Failure to provide proper
clearances may result in a fire
hazard!
NOTES:
1.
Plastic or other utensils with
low melting temperatures
should not be stored in
drawers immediately below
the cooktop.
2.
Access to the underside of
the cooktop and the junction
box must be provided for
inspection and service.
All models are designed for standard
24-inch-deep (610mm) base cabinets with
25-inch (635mm) overall depth counter
tops. Before making the countertop cutout,
make certain that the cooktop will clear the
front and side walls of the base cabinet
as shown. Clearance is required for
proper fastening of the cooktop hold down
brackets.
Also allow a minimum 2-inch (51mm)
clearance between the bottom of the
cooktop chassis and any combustible
surface, including the upper edge of a
drawer installed below the cooktop. When
installing a METB365 or ETT365-1 and
the bottom of the cooktop is intended to
be enclosed wall to wall, installation of a
ventilation duct kit is required (PN 700407).
See the duct installation instructions
(PN 100807) for cutout requirements.
The enclosure must have two ventilation
openings for the ducts measuring 8 1/2”
by 5 1/8” each. The openings are to
be located on the horizontal part of the
enclosure directly beneath the cooktop.
Locate the junction box within reach of the
included 48-inch-long (1219mm) cooktop
power lead such that the junction box is
accessible when the cooktop is in place.
Installing the Cooktop
wARNINg:
do not use a hardening
compound or caulking to
permanently seal the cooktop into
place, as the unit must be readily
removable for service. If such a
hardening compound is used,
removal of the unit will be at the
customer’s expense.
Glass Top and
Frame
Foam Tape Seal
Countertop
4“ (102mm)
Hold Down Bracket
and Screw
Cooktop Installation - Section View
Electrical Connection
wARNINgS:
1.
Ensure that the power supply
is disconnected before
proceeding.
2.
Verify that the power supply
matches the ratings found on
the appliance data plate before
proceeding. See page 2 for
location.
3.
The complete appliance must
be properly grounded at all
times when electrical power is
applied.
4.
do not ground the appliance
with the neutral (white) house
supply wire. A separate
ground wire must be utilized.
5. If aluminum house supply
wiring is utilized, splice the
appliance copper wires to the
aluminum house wiring using
special connectors designed
and agency-certified for
joining copper and aluminum.
6.
Follow the connector
manufacturer’s recommended
procedure carefully. Improper
connection can result in a fire
hazard!
These products are provided with a flexible
conduit consisting of two (2) insulated hot
lead conductors (both copper) and one (1)
insulated ground conductor (copper).
Verifying Proper Operation
wARNINgS:
1.
Never touch any heating
elements when the power is
on.
2.
If the cooktop glass is broken,
turn off power to the unit. do
not operate until glass has
been replaced by a qualified
service technician.
3.
This product must be repaired
only by a qualified service
technician. unit must be
disconnected from power
prior to service.
NOTES:
Before operating the unit:
1. Clean the glass surface
carefully using the Cooktop
Cleaning Creme provided
with the product. Remove all
cleaner residue.
2.
Read and understand the
accompanying use and
care manual. Important
safety, service and warranty
information is contained
within the manual.
If all final electrical connections are
complete as indicated, then proceed to
turn on the power. Once the power is
on, test each burner position for correct
operation.
Any problems should be reported
immediately to your installer or an
authorized Dacor servicer.
Attach the foam tape provided with the
unit to the underside of the cooktop frame.
Place and center the cooktop within
the cutout. Secure the cooktop to the
countertop utilizing the two (2) hold-down
brackets provided. Slide the brackets into
the slots located on the left and right sides
of the chassis, then tighten the screws to
the underside of the countertop.