- DL manuals
- Digitus
- Security Camera
- DN-16050
- User manual
Digitus DN-16050 User manual
Summary of DN-16050
Page 1
Ip / analog surveillance camera user’s manual dn-16050 / dn-16051 / dn-16052 please read instructions thoroughly before operation and retain it for future reference. The image shown above may differ from the actual product appearance..
Page 2
Important safeguard caution risk of electric shock caution: to reduce the risk of electric shock, do not expose this apparatus to rain or moisture. Only operate this apparatus from the type of power source indicated on the label. The company shall not be liable for any damages arising out of any imp...
Page 3
Table of contents 1. Product overview ............................................................................................................ 1 1.1 description ..........................................................................................................................................
Page 4
Overview -1- 1. Product overview 1.1 description this camera series is a network-based digital surveillance device with a built-in web server for the purpose of remote monitoring and recording. It supports tcp/ip networking for live video transmission in the format of mpeg4 or mjpeg, and you can eas...
Page 5
Overview -2- 1.4 specifications specifications dn-16050 dn-16051 dn-16052 ▓ network lan port yes lan speed 10/100 based-t ethernet supported protocols ddns, pppoe, dhcp, ntp, sntp, tcp/ip, icmp, smtp, ftp, http, rtp, rtsp frame rate ntsc:30, pal:25 number of online users 10 security multiple user ac...
Page 6
Overview -3-.
Page 7
Hardware overview -4- 2. Hardware overview 2.1 rear panel connector / button description reset default this button is hidden in the pinhole. Press and hold the reset button until the network camera rebooted. This will reset all parameters, including the ip address to factory default settings. Power ...
Page 8
Installation -5- 3. Installation 3.1 install the hardware this camera can be installed in two ways: ceiling-mounted and desktop. During the installation, please make sure the upper side of the camera is always facing up, as shown in figure 1 below, regardless of which installation way you’re using. ...
Page 9
Installation -6- 3. Assemble the bracket: a). Align the stem with the central hole of the base, and rotate it to secure, as shown in figure 3. B). Align the joint lock with the stem, and rotate it to secure, as shown in figure 4. Figure 3: connect the stem to the base figure 4: connect the joint loc...
Page 10
Installation -7- 3.2 assign an ip address and access the camera step 1. Install the software place the supplied video viewer ap software cd into your dvd- / cd-rom drive. The installation process will automatically start. Follow the on-screen instructions to install the application programs. After i...
Page 11
Video viewer basic operation -8- 4. Video viewer basic operation 4.1 the live view page after setting up the network information, login user name and password, double-click “ ” on the pc desktop to open and log into the video viewer control panel. You will see a screen similar to the following with ...
Page 12
Video viewer basic operation -9- 4.2 address book this view is displayed when the video viewer is activated for you to log in / out the network camera from the current address list, or search the available ip address as follows: ( ( a a d d d d r r e e s s s s b b o o o o k k ) ) click to view the p...
Page 13
Video viewer basic operation -10- ( ( s s e e a a r r c c h h ) ) click to search and view the available ip address(es) for the network camera connection. You can choose one address to add into the address book, edit the details, or update the address list. No. Button function description 4 add into...
Page 14
Video viewer basic operation -11- 4.4 playback to play a recording, click “ ” (miscellaneous control) → “ ” (status list), and select the “record” tab. A list of all the recordings will be shown by defaults, and you can also sort out the logs you want to speed up the search time. For details, please...
Page 15
Video viewer basic operation -12- 4.5 snapshot to take a snapshot of the current view, click “ ” (snapshot) on the main control panel. Once the current view is captured, you’ll see an icon “ ” shown at the bottom right corner of the image display view. The snapshot will be saved in the path you spec...
Page 16
Video viewer miscellaneous control panel -13- 5. Video viewer miscellaneous control panel click “ ” (miscellaneous control) on the video viewer control panel, and 7 functions are available as follows: click the button to show the current version of the video viewer. The audio / broadcast function is...
Page 17
Video viewer miscellaneous control panel -14- 5.1 color setting in the live view page, choose the desired network camera from the image display tab. Click “ ” (miscellaneous control) → “ ” (color setting) to go into the “color setting” page, and you can adjust the brightness / contrast / hue / satur...
Page 18
Video viewer miscellaneous control panel -15- no. Function description ‧ to quickly find the events you need, check or uncheck the event type “system” / “manual” / “alarm” / “motion”, and select the log you want. ‧ to view the earlier or later logs that are not shown in the current page, click “prev...
Page 19
Video viewer miscellaneous control panel -16- prev / post event record time in this section, you can set the pre- / post-event record time from 0 ~ 10 seconds by pressing and dragging the slider. Hard disk overwrite check this checkbox to overwrite from the oldest recorded data when the hdd is full....
Page 20
Video viewer miscellaneous control panel -17- to delete a certain item, choose the item you want to delete, and click “delete”. To modify a certain item, choose the item you want to modify, change the start time and end time, and click “update”. Record path select and view the location for saving th...
Page 21
Video viewer miscellaneous control panel -18- log click “ ” (miscellaneous control) → “ ” (server setting) → “general” → “log” to go into the “log” page. In the “log” page, you can see all the logs for the network camera, such as “power on”, “reset default”, “net login” and “sntp update” … etc. ‧ to...
Page 22
Video viewer miscellaneous control panel -19- column description for the functions each user level is allowed to access, please see the information below: supervisor power user normal user guest address book ● ● ● ● miscellaneous control color setting ● x x x backup ● x x x record setting ● ● ● ● se...
Page 23
Video viewer miscellaneous control panel -20- motion trigger: in this section, you can select to enable the function of motion trigger. Before this function is enabled, you need to set the motion detection area first. For motion detection area setting, please refer to “detection” at page 26. Item de...
Page 24
Video viewer miscellaneous control panel -21- function description pppoe pppoe stands for point-to-point protocol over ethernet. Users can easily have the internet service as long as they’re ready for the following things: 1) insert an ethernet card into the pc. 2) obtain the adsl service via any is...
Page 25
Video viewer miscellaneous control panel -22- ‧ then, you will see the screen “account created”, and dyndns will email the instructions to your specified e-mail address for enabling your account. You must complete the procedure according to the instructions in the mail. That is to must visit the con...
Page 26
Video viewer miscellaneous control panel -23- ‧ log in with your account information and click ”my service”. ‧ click ”add host services”. ‧ click ”add dynamic dns host”. ‧ fill in and choose the desired host name. ‧ the host name is created. You will be connected to the corresponding ip address when...
Page 27
Video viewer miscellaneous control panel -24- sntp sntp (simple network time protocol) is for time setting. Click “ ” (miscellaneous control) → “ ” (server setting) → “network” → “sntp” to go into the “sntp” page. Function description gmt (greenwich mean time) once users choose the time zone, the ne...
Page 28
Video viewer miscellaneous control panel -25- mail click “ ” (miscellaneous control) → “ ” (server setting) → “network” → “mail” to go into the “mail” page. Enter the detailed e-mail information and press “apply” to confirm. The information you set here will be applied when the function of e-mail no...
Page 29
Video viewer miscellaneous control panel -26- item description the actual frame rate depends on the actual network connection, and may be lower than the specified one. Maximum exposure limits to compensate for the lighting conditions, the maximum exposure time can be adjusted. There are five levels ...
Page 30
Video viewer miscellaneous control panel -27- function description update server select the ip address of the network camera. Make sure the network settings of the selected network camera are correct. Current version in the “firmware” section, you will see the current firmware version. For example, ...
Page 31
Video viewer miscellaneous control panel -28- 5.6 status list click “ ” (status list) to view all the record list and login/logout event list ( all ), or search the desired log list(s) by date, or playback the recording of the selected log list ( condition ). There are three types of logs: record, e...
Page 32
Ap miscellaneous control panel -29- ‧ condition button / function description date selection (from / to) choose the specific date range including the event / record logs you might want. Record type this section is enabled only when the “record” tab is selected. Select the record type you want to sea...
Page 33
Ap miscellaneous control panel -30- login / logout event list select “ all ” to show all event logs (login / logout), or “ condition ” to search for the specific event log(s) by date. ‧ all ‧ condition.
Page 34
Ap miscellaneous control panel -31- backup list (for dvr only) the network cameras don’t support network backup function. This function is available when the video viewer is connected to a dvr. You can remotely view the backup list and playback the selected item. Select “ all ” to show all download ...
Page 35
Ap miscellaneous control panel -32- playback screen when you select and play the recorded data for a specific log, you will immediately go into the playback mode, and the following playback panel appears. No. Function description playback / download info display this area shows the detailed playback...
Page 36
Ie web browser -33- 6. Ie web browser 6.1 access the camera from an ie web browser you can view the images or operate your network camera from an ie web browser. Note: the supported pc operation systems are windows 2000 and windows xp. Step 1: key in the ip address used by your network camera in the...
Page 37
Ie web browser -34- no. Function description 3 camera snapshot path set the location where the snapshot pictures are saved. Frame rate according to the bandwidth, set the required frame rate (full / half / one third / quarter / one fifth / one tenth / one fifteenth). For details, please refer to “vi...
Page 38
Quicktime player -35- 7. Quicktime player you can also use the quicktime player to log into the network camera and check the live view only. Note: quicktime is apple’s multimedia software. You need to have quicktime installed in you computer first, and you can access the network camera to see the li...
Page 39
Appendix 1 default value -36- appendix 1 default value ‧ default value items default value ‧ default network settings: user name admin password admin port 80 ip address 192.168.1.10