Dimplex LPC Series Installation And Operation Instructions
7211700100R13
Linear Proportional Convector Heater
LPC Series
Placement of the Linear Proportional Convector
Linear Proportional Convectors are high performance heaters de-
signed to operate at higher outlet temperatures than conventional
baseboard heaters. They can be directly mounted onto drywall,
plaster, wood or concrete walls. Due to the higher outlet tempera-
ture, the wall surface can reach temperatures of 160º F (71º C) or
above and some materials may discolor or deform at these temper-
atures, e.g. vinyl or plastic. In these cases the heater can be mount-
ed with an offset from the wall and floor to reduce the temperature
being applied to those materials. By installing the heater 5/8” (1.6
cm) off the wall and 1/4” (0.6 cm) off of the floor, the temperature of
the wall above the heater can be reduced to 129º F (54º C).
!
NOTE: If the unit is being installed on a newly constructed
wall, ensure that all products that have been applied are fully
cured according to manufacturer’s instructions, before operating
the unit.
Recommendations for Locating Drapes and
Furniture near Heater (Figure 1)
!
NOTE: Any objects or materials that are located within the
distances outlined below should not discolor, nor distort dimen-
sionally (stretch or shrink) upon extended exposure ( up to 1000
hrs.) to temperatures of 200º F (93º C).
For most satisfactory operation of the heaters and minimum effect
on drapes, furniture and objects in close proximity, the following
recommendations should be observed:
1. Full Length Drapes: Hang drapes so there is at least 1.5” (3.8
cm) between the top of the drapes and the ceiling, at least 1.5”
(3.8cm) between the bottom of the drapes and the finished floor
covering (such as carpet, if used) AND at least 3” (7.6 cm) be-
tween the front vertical surface of the heater and the nearest fold
of the drapes (opened drape). (Figure 1A)
2. Shorter Length Drapes: Hang drapes so there is at least 1.5”
(3.8 cm) between the top of the drapes and the ceiling, and at
least 6” (15.2 cm), preferably more, between the bottom of the
drapes and the top horizontal surface of the heater. (Figure 1B)
3. Furniture: Place furniture no closer than 3” (7.62 cm) from the
front of the Linear Proportional Convector. (Figure 1D)
4. Overhanging Solid Objects (Except Plastic): Position Linear
Convector so there is at least 14” (35.6 cm) between the top of
the heater and any solid object that obstructs or redirects the
vertical air flow out of the top of the unit. (Figure 1C)
5. Overhanging Plastic Objects: All Plastic items that cannot with-
stand extended exposure to temperatures 60º C or higher should
be kept a minimum of 20” (50.8cm) above the unit. (Figure 1C))
!
NOTE: Ensure that when 2 Linear Proportional Convectors are
Installation Instructions
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always
be followed to reduce the risk of fire, electric shock and injury to
person, including the following:
1. Read all instructions before using this heater.
2. Heater and controls should be installed by a qualified contrac-
tor. Wiring procedures and connections should be in accor-
dance with the National Electric Code (CEC & NEC) and local
codes.
3. A heater has hot and arcing or sparking parts inside. Do not
use it in areas where gasoline, paint or flammable liquids are
used or stored.
4. This heater is hot when in use. To avoid burns, do not let bare
skin touch hot surfaces. Keep combustible materials such as:
furniture, pillows, bedding, papers, clothes and curtains away
from heater.
5. To prevent a possible fire, do not block air intakes or exhaust
in any manner. Do not use on soft surfaces like a bed where
openings may become blocked.
6. Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock or fire, or
damage the heater.
7. Do not install these heaters against combustible, low density
cellulose fibre surfaces or vinyl wall paper.
8. Do not locate these heaters below any electrical convenience
receptacles.
9. Check nameplate ratings to be sure the heater voltage is the
same as the service supply. (The nameplate is located below
the right side of the heating element.)
10. HIGH TEMPERATURES: Keep electrical cords, furniture, drap-
eries or any other blocking material away from the heater. See
Installation Section for specific distances.
SAVE THESE INSTRUCTIONS
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of
the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC CAUTION: Any changes or modifications not expressly approved
by the party responsible for compliance could void the user’s authority to
operate this equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, includ-
ing interference that may cause undesired operation of the device.
Figure 1
A
B
C
D
Min.
1.5" (3.8 cm)
Min.
1.5" (3.8 cm)
Min.
1.5" (3.8cm)
Min.
3" (7.6 cm)
Min.
3" (7.6 cm)
Min.
3" (7.6 cm)
Min.
6" (15.3 cm)
Min.
See Item 4 & 5
for Dimension