Dimplex LPC Series Installation Instructions

7211700100R15

Linear Proportional Convector Heater

LPC Series

Placement of the Linear Proportional Convector

Linear Proportional Convectors are high performance heat-

ers designed to operate at higher outlet temperatures than 

conventional baseboard heaters. They can be directly mount-

ed onto drywall, plaster, wood or concrete walls. Due to the 

higher outlet temperature, the wall surface can reach temper-

atures of 160º F (71º C) or above and some materials may 

discolor or deform at these temperatures, e.g. vinyl or plastic. 

In these cases the heater can be mounted with an offset from 

the wall and floor to reduce the temperature being applied to 

those materials. By installing the heater 5/8” (1.6 cm) off the 

wall and 1/4” (0.6 cm) off of the floor, the temperature of the 

wall above the heater can be reduced to 129º F (54º C). 

!

 NOTE: If the unit is being installed on a newly con-

structed wall, ensure that all products that have been 

applied are fully cured according to manufacturer’s instruc-

tions, before operating the unit.

Recommendations for Locating Drapes and 

Furniture near Heater (Figure 1)

!

 NOTE: Any objects or materials that are located within the 

distances outlined below should not discolor, nor distort 

dimensionally (stretch or shrink) upon extended exposure 

( up to 1000 hrs.) to temperatures of 200º F (93º C).

For most satisfactory operation of the heaters and minimum 

effect on drapes, furniture and objects in close proximity, the 

following recommendations should be observed: 

1. Full Length Drapes: Hang drapes so there is at least 1.5” 

(3.8 cm) between the top of the drapes and the ceiling, at 

least 1.5” (3.8cm) between the bottom of the drapes and 

the finished floor covering (such as carpet, if used) AND at 

least 3” (7.6 cm) between the front vertical surface of the 

heater and the nearest fold of the drapes (opened drape). 

(Figure 1A)

2. Shorter Length Drapes: Hang drapes so there is at least 

1.5” (3.8 cm) between the top of the drapes and the ceil-

ing, and at least 6” (15.2 cm), preferably more, between 

the bottom of the drapes and the top horizontal surface of 

the heater. (Figure 1B)

 Installation Instructions

 IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should 

always be followed to reduce the risk of fire, electric shock 

and injury to person, including the following: 

1.  Read all instructions before using this heater.

2.  Heater and controls should be installed by a qualified 

contractor. Wiring procedures and connections should 

be in accordance with the National Electric Code (CEC & 

NEC) and local codes.

3.  A heater has hot and arcing or sparking parts inside. Do 

not use it in areas where gasoline, paint or flammable 

liquids are used or stored.

4.  This heater is hot when in use. To avoid burns, do not let 

bare skin touch hot surfaces. Keep combustible materials 

such as: furniture, pillows, bedding, papers, clothes and 

curtains away from heater.

5.  To prevent a possible fire, do not block air intakes or 

exhaust in any manner. Do not use on soft surfaces like 

a bed where openings may become blocked.

6.  Do not insert or allow foreign objects to enter any venti-

lation or exhaust opening as this may cause an electric 

shock or fire, or damage the heater.

7.  Do not install these heaters against combustible, low 

density cellulose fibre surfaces or vinyl wall paper.

8.  Do not locate these heaters below any electrical conve-

nience receptacles.

9.  Check nameplate ratings to be sure the heater voltage 

is the same as the service supply. (The nameplate is 

located below the right side of the heating element.)

10. HIGH TEMPERATURES: Keep electrical cords, furniture, 

draperies or any other blocking material away from the 

heater. See Installation Section for specific distances.

SAVE THESE INSTRUCTIONS

This equipment has been tested and found to comply with 

the limits for a Class B digital device, pursuant to Part 15 of 

the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference in a residential 

installation. This equipment generates uses and can radiate 

radio frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful interfer-

ence to radio communications. However, there is no guaran-

tee that interference will not occur in a particular installation. 

If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct 

the interference by one of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and 

receiver.

•  Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV techni-

cian for help.

This device complies with Part 15 of the FCC Rules. Opera-

tion is subject to the following two conditions: (1) This device 

may not cause harmful interference, and (2) this device must 

accept any interference received, including interference that 

may cause undesired operation.

 FCC CAUTION: Any changes or modifications not ex-

pressly approved by the party responsible for compliance 

could void the user’s authority to operate this equipment.

This device complies with Industry Canada licence-exempt 

RSS standard(s). Operation is subject to the following two 

conditions: (1) this device may not cause interference, and 

(2) this device must accept any interference, including inter-

ference that may cause undesired operation of the device.