E.F. Johnson 5100 SERIES Service Manual - page 38
OPERATION
2-27
September 2001
Part No. 001-5100-001
shows the keypad programming mode menu structure
for this radio.
The information which follows describes how the
various parameters are programmed. When program-
ming is complete, exit the keypad programming mode
by turning power off. Do not turn power on again for a
short time so that the radio has time to copy the
settings to memory.
2.9.3 CLONING
The cloning mode is used to program one trans-
ceiver with another with identical information. A
special cloning cable is required to connect the trans-
ceivers together. To enter this mode, on the master
(sending) radio, press the
#
(pound) key with “RAD
PARM” displayed. The clone mode is then indicated
by “CLONE?”. To return to “RAD PARM” without
cloning, press the
key. To clone a radio, connect the
cloning cable, power up the slave (receiving) radio,
and press the
ENT
key on the master (sending) radio.
When cloning is successfully completed, “RAD
PARM” is again displayed. Encryption keys are not
transferred.
2.9.4 TIMER PROGRAMMING
The menus to program the following timers are
accessed by repeatedly pressing the
#
key with “RAD
PARM” displayed. To return to the previous adjust-
ment, press the
key.
TX TMR -
Programs the transmit time-out timer (see
page 7). Press the
and
keys to decrement/incre-
ment the timer in 15-second steps (“0” disables it).
When the desired value is displayed, store it by
pressing the
ENT
(
F4
) key.
PEN TMR -
Programs the penalty timer (see
page 12). Press the
and
keys to decrement/
increment the timer in 15-second steps (“0” disables
it). When the desired value is displayed, store it by
pressing the
ENT
(
F4
) key.
CONV TMR -
Programs the conversation timer (see
page 12). Press the
and
keys to decrement/
increment the timer in 30-second steps (“0” disables
it). When the desired value is displayed, store it by
pressing the
ENT
(
F4
) key.
2.9.5 CHANNEL PROGRAMMING
Zone Selection
The zone containing the channel to be
programmed must be selected if applicable. To do this,
with “RAD PARM” displayed press the key corre-
sponding to the zone containing the channel. Alterna-
tively, press the
and
keys to scroll through the
programmed zones and the “RAD PARM” selection.
The zone selection mode is indicated by “ZONE x”.
To return to “RAD PARM”, press the
CLR
key. To
proceed to channel parameter programming described
in the next section, press the
#
key.
Channel Selection
The channel to be programmed must be selected.
To do this, press the # key with “ZONE x” displayed
as described in the preceding section. The display then
indicates “CHAN xx”. Then to select the desired
channel, press the
and
keys to scroll through
the programmed channels or enter the channel number
directly using the number keys. Disabled or
SMARTNET/SmartZone channels cannot be selected.
To exit back to the “ZONE x” display, press the
key with “CHAN xx” displayed. To save the selec-
tion and proceed with the channel parameter program-
ming described in the next section, press the
ENT
or
#
key.
Channel Parameter Programming
After selecting the channel to be programmed as
described in the preceding section, the following
channel parameters can be programmed. To scroll
through these parameters, press the
ENT
or
#
key with
“CHAN xx” displayed. To go back to the previous
field, press the
key. The squelch control parameters
are unique to the type of conventional channel selected
(analog or Project 25).
Channel Spacing -
Selects either “WIDE” or
“NARROW” band channel spacing on analog chan-
nels only. Press the
and
keys to toggle between
“WIDE” and “NARROW”, and when the desired
setting is displayed, save it and proceed to the next
parameter by pressing the
ENT
or
#
key.
*
*
*
*