Summary of Hurricane 25e TM
Page 1
? tm hurricane 25e assembly manual montageanleitung manuel d’assemblage manuale di montaggio.
Page 2
2 e-flite hurricane 25e pnp/bnf assembly manual en notice all instructions, warranties and other collateral documents are subject to change at the sole discretion of horizon hobby, inc. For up-to-date product literature, visit http://www.Horizonhobby. Com and click on the support tab for this produc...
Page 3
3 e-flite hurricane 25e pnp/bnf assembly manual en table of contents notice ................................................................... 2 meaning of special language ................................. 2 additional safety precautions and warnings ........... 2 introduction .......................
Page 4
4 e-flite hurricane 25e pnp/bnf assembly manual en required tools and adhesives tools & equipment balancing stand cut-off wheel epoxybrush drillbit:3/16-inch(5mm) flatfile mixingcup mixingstick open-endwrench:3/4-inch paper towel petroleum jelly rotary tool phillips screwdriver: #1 ruler vise grip h...
Page 5
5 e-flite hurricane 25e pnp/bnf assembly manual en the battery charging process 1. Charge only batteries that are cool to the touch and are not damaged. Look at the battery to make sure it is not damaged e.G., swollen, bent, broken or punctured. 2. Attach the input cord of the charger to the appropr...
Page 6
6 e-flite hurricane 25e pnp/bnf assembly manual en 2. Remove the spinner cone by pulling the cone forward from the spinner backplate. 3.Usea3/4-inchboxwrenchtoremovethe propeller nut from the motor adapter. 4. Remove the propeller from the motor adapter. We recommend removing the spinner backplate a...
Page 7
7 e-flite hurricane 25e pnp/bnf assembly manual en transmitter and receiver binding - bnf required parts fuselage assembly transmitter bind plug binding is the process of programming the receiver of the control unit to recognize the guid (globally unique identifier) code of a single specific transmi...
Page 8
8 e-flite hurricane 25e pnp/bnf assembly manual en 2. Fit the stabilizer half to the fuselage by sliding the tube into position. The stabilizer will fit tightly in the plastic fairing. 3. Fit the other stabilizer half into position. Both halves will fit tightly in the fairing when installed. If not,...
Page 9
9 e-flite hurricane 25e pnp/bnf assembly manual en main gear installation - bnf/pnp required parts wing panel (right and left) landing gear assembly (right and left) landing gear door (right and left) landing gear mount cover (right and left) 2.5mmx12mmself-tappingscrew(8) required tools and adhesiv...
Page 10
10 e-flite hurricane 25e pnp/bnf assembly manual en optional retract installation - bnf/pnp required parts (included with model) wing panel (right and left) landing gear door (right and left) landing gear mount cover (right and left) wheel(2)(removedfromfixedgear) 3mm wheel collar with screw (2) (re...
Page 11
11 e-flite hurricane 25e pnp/bnf assembly manual en 5. Position the gear strut in the retract unit so that the coil is parallel with the centerline of the fuselage. Anexcellentvisualcueforthisistoalignthecoil with the rib under the coil. The gear strut should orient towards the wing tip with the coi...
Page 12
12 e-flite hurricane 25e pnp/bnf assembly manual en 10. Use a hobby knife to open the hole drilled in theprevioussteptofitaservoextensionthrough. Maketheholejustbigenoughfortheextensionto avoid weakening the wing. 11. Secure a 12-inch (305mm) servo lead to the retract lead. Use two-sided tape to sec...
Page 13
13 e-flite hurricane 25e pnp/bnf assembly manual en 15. Use a rotary tool and cut-off wheel to trim the axleatthemarkmadeinstep12.Usevisegripsto hold the wire and to act as a heat-sink. This will keep the heat from cutting the wire from transferring back to the retract mechanism, which could melt th...
Page 14
14 e-flite hurricane 25e pnp/bnf assembly manual en 2. Insert the bend in the flap linkage in the innermost hole in on the flap servo arm. Remove the tape from the flaps at this time as well. 3. Enter the radio programming and set the flap throw to 100% for both up and down positions, and verify tha...
Page 15
15 e-flite hurricane 25e pnp/bnf assembly manual en 1. Locate the carbon fiber wing tube. Slide the tube in one wing panel. It should slide in easily, so do not force it farther than it will slide. This will push the wing tube into the foam in the wing, and possibly prevent it from inserting fully i...
Page 16
16 e-flite hurricane 25e pnp/bnf assembly manual en caution: the installation of the foam radiator scoop and bolt plates on the wing are integral parts of joining the wing properly. Make sure these items are glued securely to the wing to prevent wing failure. Receiver installation - pnp required par...
Page 17
17 e-flite hurricane 25e pnp/bnf assembly manual en 4. Use two-sided tape to secure the receiver in the fuselage as shown. 5. Place the longer antenna into the groove in the inside of the fuselage. Use clear tape to keep the antenna in the groove so it doesn’t interfere with the operation of the ser...
Page 18
18 e-flite hurricane 25e pnp/bnf assembly manual en center the control surfaces - bnf/pnp required parts canopy hatch assembled airframe transmitter antenna mast 1. Turn on the transmitter and connect the motor battery to the speed control. Verify the operation of the servos. 2. Center the trims and...
Page 19
19 e-flite hurricane 25e pnp/bnf assembly manual en center of gravity required parts assembled airframe required tools and adhesives balancing stand felt-tipped pen caution: do not inadvertently skip this step or property damage and injury could occur. When balancing your model, adjust the motor bat...
Page 20
20 e-flite hurricane 25e pnp/bnf assembly manual en rudder high rate right: 1 1 / 8 -inch 29mm 25%expo left: 1 1 / 8 -inch 29mm 25%expo low rate right:7/8-inch23mm 15%expo left: 7/8-inch23mm 15%expo flap mid 13/16-inch 20mm full 1 5 / 8 -inch 41mm measurements are taken at the inner or widest point ...
Page 21
21 e-flite hurricane 25e pnp/bnf assembly manual en daily flight checks 1. Check the battery voltage of the transmitter battery. Do not fly below the manufacturer’s recommended voltage. To do so can crash your aircraft. When you check these batteries, ensure you have the polaritiescorrectonyourexpan...
Page 22
22 e-flite hurricane 25e pnp/bnf assembly manual en inspection or services if this product needs to be inspected or serviced, please use the horizon online service request submission process found on our website or call horizon to obtain a return merchandise authorization (rma) number. Pack the prod...
Page 23
23 e-flite hurricane 25e pnp/bnf assembly manual en compliance information for the european union declaration of conformity (in accordance with iso/iec 17050-1) no. Hh2011031501 product(s): efl hawker hurricane 25e pnp item number(s): efl2975 equipment class: 1 the object of declaration described ab...
Page 24
24 e-flite hurricane 25e pnp/bnf assembly manual en academy of model aeronautics national model aircraft safety code effective january 1, 2011 a. General a model aircraft is a non-human-carrying aircraft capable of sustained flight in the atmosphere. It may notexceedlimitationsofthiscodeandisintende...
Page 25
25 e-flite hurricane 25e pnp/bnf assembly manual en c. Free flight 1. Must be at least 100 feet downwind of spectators and automobile parking when the model aircraft is launched. 2. Launch area must be clear of all individuals except mechanics, officials, and other fliers. 3. An effective device wil...
Page 26
27625 created 5/2011 © 2011 horizon hobby, inc. Horizonhobby.Com www.E-fliterc.Com the spektrum trademark is used with permission of bachmann industries, inc. E-flite, jr sport, dsm, dsm2 and ultracote are trademarks or registered trademarks of horizon hobby, inc. All other trademarks, service marks...