E-FLITE Hurricane 25e TM Assembly Manual - page 4
4
E-flite Hurricane 25e PNP/BNF Assembly Manual
EN
Required Tools and Adhesives
Tools & Equipment
Balancing stand
Cut-off wheel
Epoxybrush
Drillbit:3/16-inch(5mm)
Flatfile
Mixingcup
Mixingstick
Open-endwrench:3/4-inch
Paper towel
Petroleum jelly
Rotary tool
Phillips screwdriver: #1
Ruler
Vise grip
Hexwrench:2.5mm
Hobby knife with #11 blade
Adhesives
30-minuteepoxy
PAAPT39
Threadlock PAAPT42
During the course of building your model, we suggest
you use a soft base for the building surface. Things like
a foam stand, large piece of bedding foam or a thick
bath towel will work well and help protect the model
from damage during assembly. This is not shown in the
instructions to provide the greatest detail in the photos.
When referencing directions (up, down, left,
right, top and bottom), these directions are in
relationship to the pilot sitting in the cockpit
of the aircraft unless noted otherwise.
Charging the Flight Battery - BNF
Required Parts
Charger
Motor battery
12V power supply or AC adapter
BATTERY WARNINGS
The Battery Charger included with your aircraft is
designed to safely charge the Li-Po battery.
CAUTION: All instructions and warnings
mustbefollowedexactly.MishandlingofLi-Po
batteries can result in a fire, personal injury,
and/or property damage
• Byhandling,chargingorusingtheincludedLi-Po
battery you assume all risks associated with lithium
batteries.
• Ifatanytimethebatterybeginstoballoonor
swell, discontinue use immediately. If charging or
discharging, discontinue and disconnect. Continuing
to use, charge or discharge a battery that is
ballooning or swelling can result in fire.
• Alwaysstorethebatteryatroomtemperatureina
dry area for best results.
• Alwaystransportortemporarilystorethebattery
in a temperature range of 40–120º F. Do not store
battery or model in a car or direct sunlight. If stored
in a hot car, the battery can be damaged or even
catch fire.
• NEVERUSEANi-CdORNi-MHCHARGER.Failure
to charge the battery with a compatible charger
may cause fi re resulting in personal injury and/or
property damage.
• NeverdischargeLi-Pocellstobelow3Vunderload.
• Nevercoverwarninglabelswithhookandloopstrips.
• Neverleavechargingbatteriesunattended.
• Neverchargebatteriesoutsidesafetemperaturerange.
• Neverchargedamagedbatteries.
Your model comes with a DC balancing charger and
3S Li-Po battery. You must charge the included Li-Po
battery pack with a Li-Po specific charger only (such
as the included charger). Never leave the battery and
charger unattended during the charge process. Failure
to follow the instructions properly could result in a
fire. When charging, make certain the battery is on a
heat-resistant surface. Charge the flight battery while
assembling the aircraft. Install the fully charged battery
to perform control tests and binding.
DC LI-PO BALANCING CHARGER FEATURES
•Charges2-to3-celllithiumpolymerbatterypacks
•Variablechargeratesfrom300mAhto2-amp
•Simplesinglepush-buttonoperation
•LEDchargestatusindicator
•LEDcellbalanceindicator
•Audiblebeeperindicatespowerandchargestatus
•12VaccessoryoutletinputcordSpecifications
•Inputpower:12VDC,3-amp
•Charges2-to3-cellLi-Popackswithminimum
capacity of 300mAh
The included 3S Li-Po battery pack features a
balancing lead that allows you to safely charge
your battery pack when used with the included Li-Po
balancing charger.
NOTICE: Do not use a 6V power supply with
this charger.