Summary of The Beast
Page 1
® ™ instruction manual • bedienungsanleitung • manuel d’utilisation • manuale di istruzioni.
Page 2: Meaning of Special Language
2 en warning: read the entire instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product. It must be operated ...
Page 3: First Flight Preparation
3 en to register your product online, go to http://www.E-flite.Com beast specifications wingspan length weight 14.7 in (372mm) 15.7 in (400mm) 2.0 oz (57 g) designed by aerobatic world champion quique somenzini, the ultra micro extreme (umx) beast® is a thrilling small-scale recreation of one of the...
Page 4: Battery Warnings
4 en the battery charger (efluc1007) included with the beast bnf has been designed to safely charge the li-po battery. You must read the following safety instructions and warnings before handling, charging or using the li-po battery. Caution: all instructions and warnings must be followed exactly. M...
Page 5: Charging The Battery
5 en charging the battery the battery charging process 1. Charge only batteries that are cool to the touch and are not damaged. Look at the battery to make sure it is not damaged e.G., swollen, bent, broken or punctured. 2. The connector on the battery is specifically designed to allow the battery t...
Page 6: Installing Flight Battery
6 en binding is the process of programming the receiver of the control unit to recognize the guid (globally unique identifier) code of a single specific transmitter. You need to ‘bind’ your chosen spektrum dsm2 technology equipped aircraft transmitter to the receiver for proper operation. Note: any ...
Page 7: Control Direction Test
7 en you should bind your aircraft and transmitter before doing these tests. Move the controls on the transmitter to make sure aircraft control surfaces are moved correctly. Note: make sure tail pushrods move freely and that paint or decals are not adhered to them. Control direction test elevator el...
Page 8: Control Centering
8 en in the event of an accident or before first flights, check to make sure the flight control surfaces are centered. It is much better to do this mechanically and not use sub-trims due to the mechanical limit of linear servos. 1. Make sure the transmitter’s trims are centered, and if your transmit...
Page 9: Flying Tips and Repairs
9 en flying always avoid flying near houses, trees, wires and buildings. You should also be careful to avoid flying in areas where there are many people, such as busy parks, schoolyards, or soccer fields. Consult local laws and ordinances before choosing a location to fly your aircraft. We recommend...
Page 10
10 en service of power components disassembly propeller •removebatteryhatchbyslidingitforward, then up and away from the fuselage. •removescrew,spinner,propellerandback- plate from the motor shaft. Figure a. •carefullyremovespinnerfrompropellerand backplate. Figure b. Note: since the propeller and s...
Page 11
11 en service of power components b d f h c a e g i.
Page 12: Troubleshooting Guide
12 en troubleshooting guide problem possible cause solution •aircraftwillnotrespond to throttle but responds to other controls •throttlenotatidleand/orthrottle trim too high. •throttlechannelisreversed •resetcontrolswiththrottlestick and throttle trim at lowest setting •reversethrottlechannelon tran...
Page 13
13 en replacement and optional parts number description eflu4059 wing set: umx beast eflu4064 cabane: umx beast eflu4058 fuselage set: umx beast eflu4060 tail surface set: umx beast eflu4054 wheel pants set: umx beast eflu4055 landing gear with wheels: umx beast eflu4062 battery hatch: umx beast efl...
Page 14: Warranty and Repair Policy
14 en warranty period exclusive warranty- horizon hobby, inc., (horizon) warranties that the products purchased (the “product”) will be free from defects in materials and workmanship at the date of purchase by the purchaser. Limited warranty horizon reserves the right to change or modify this warran...
Page 15: Contact Information
15 en contact information country of purchase horizon hobby address phone number/email address horizon service center (electronics and engines) 4105 fieldstone rd champaign, illinois 61822 usa 877-504-0233 productsupport@horizonhobby.Com horizon product support (all other products) 4105 fieldstone r...