Spraystation® hv1900 operating manual en.
Hv1900 1 6 3 2 1 4 7 3 a spraystation® hv1900 operating manual en b a 2 5a 5b b.
Hv1900 4 5 a b c 7 a c 20-30 cm b 6.
Hv1900 a b 12 8 2 1 10 need image need image 1 2 4 6 5 9 7 8 3 1 2 3 4 11.
En 1 hv1900 many thanks for placing your trust in us we would like to congratulate you on purchasing this earlex product; we are sure that you will enjoy working with it greatly. Please read the operating manual carefully and observe the safety information before starting the tool. Store the operati...
En 2 hv1900 1. Explanation of symbols used this symbol indicates a potential danger to you or for the tool. Under this symbol you can find important information on how to avoid injuries and damage to the power tool. Danger of electrical shock i indicates tips for use and other particularly useful in...
En 3 hv1900 d) do not misuse the supply cord by carrying the tool by the cord, hanging it from the cord or by pulling on the cord to remove the plug. Keep the supply cord away from heat, oil, sharp edges or moving tool parts. Damaged or twisted leads increase the risk of an electric shock. E) if you...
En 4 hv1900 4. Power tool use and care a) do not overload the tool. Use the power tool designed for the work that you are doing. You work better and safer in the specified performance range if you use the suitable power tool. B) do not use power tools whose switch is defective. A power tool that can...
En 5 hv1900 socket-outlets and plugs must be masked. Risk of an electric shock as a consequence of sprayed material entering the socket-outlet! • do not use the spray guns to spray flammable substances. • the spray guns are not to be cleaned with flammable solvents. • caution against dangers that ca...
En 6 hv1900 5. Field of application many different coating substances can be processed with this tool. 6. Coating materials suitable for use interior wall paint (dispersions and latex paint) water and solvent-based paints, finishes, primers, clear finishes, staining sealers and wood sealer preservat...
En 7 hv1900 9. Preparation of the coating material • mix the material well in the original container. When using interior wall paint, an agitator is recommended. I the viscosity (thickness) of your paint may need thinning before spraying. Start with a 10% dilution. Stir well. If further thinning is ...
En 8 hv1900 i spend some time practising on cardboard or a similar surface in order to determine the right flow rate of paint and air for the best spray pattern. Detailed information about these settings can be found in chapter 11- 12. 11. Selecting the spray setting warning! Danger of injury! Never...
En 9 hv1900 fig. 7 a / 7 b: correct even distance to the object. Fig. 7 c: incorrect an uneven distance will result in uneven paint application. • move the spray gun evenly side to side or up-and-down, depending on the spray pattern setting. • an even movement of the spray gun results in an even sur...
En 10 hv1900 16. Cleaning the fluid tip and needle 1) unscrew air cap ring (fig. 9, 1) 2) remove spray direction lever (fig. 9, 3) 3) it is recommended that you push the trigger forward to help release the fluid tip (fig. 9, 4) 4) using the needle and fluid tip tool - pincer end (fig. 10, 1) remove ...
En 11 hv1900 18. Spare parts spare parts designation reference order no. Air cap + ring + spray direction lever fig 9, 1,+2+3 ear2353941 suction tube fig 2,a/b ear2353955 paint container seal (pack of 3) fig 9, 7 ear2353969 needle and fluid tip tool fig 1, 5 ear2353938 viscosity cup fig 1, 6 ear2353...
En 12 hv1900 21. Important note regarding product liability! According to an ec directive, the manufacturer is liable for this product only if all parts originate from or were approved by the manufacturer and the tools are assembled and operated correctly. The use of other accessories and spare part...
En 13 hv1900 malfunction cause remedy too much fog of coating material (overspray) • distance to the object too large • too much coating material applied, material volume setting too high • amount of air too high ➞ reduce distance ➞ alter material volume adjuster ➞ alter material volume adjuster pai...
En 14 hv1900 warning this unit is a class ii appliance which means it is double-insulated for your protection, no earthing wire is necessary. If the supply cord is damaged, it must be replaced by the manufacturer or its appointed agents to avoid a safety hazard. Your unit has been supplied with a su...
En 15 hv1900 2 year guarantee the guarantee runs for two years, counting from the date of sale (sales slip). It covers and is restricted to free-of-charge rectification of faults which are demonstrably attributable to the use of faulty materials in manufacture, or assembly errors; or free- of-charge...
En 16 hv1900 ec declaration of conformity we declare under sole responsibility that this product conforms to the following relevant stipulations: 2006/42/ec; 2004/108/ec; 2011/65/eu; 2002/96/ec; 2006/95/ec applied harmonised norms: en 60335-1:2012, en 62233:2008 en 55014-1:2006 + a1:2009 + a2:2011, ...
En 17 hv1900
En 18 hv1900 part. No. V0400 01/15 © copyright wagner spraytech (uk) ltd. Www.Earlex.Com not responsible for errors and changes. Nl wsb finishing equipment bv de heldinnenlaan 200 3543 mb utrecht +31/30/2 41 41 55 +31/30/2 41 17 87 aus wagner spraytech australia pty. Ltd 14-16 kevlar close, braesi...