Summary of BA-EZ27g
Page 1
Easy-lam green ™ ba-ez27g roll laminator.
Page 2: Table of Contents
2 table of contents safety messages and electrical safeguards……………..3-4 introduction ....................................................................... 4 laminator features.......................................................... 4 specifications...................................................
Page 3: Important Safety Messages
3 important safety messages and electrical safeguards for your protection, do not connect the laminator to electrical power or attempt to operate it until you read these instructions completely. Keep these instructions in a convenient location for future reference. This instruction manual and labels...
Page 4: Introduction
4 do not overload electrical outlets beyond their capacity as this can result in fire or electrical shock. This unit is rated at 15 amps and should be the only item plugged into a 15 or 12 amp branch circuit. When connected to a 20 amp branch circuit any items in addition to the ez27 must not exce...
Page 5: Specifications
5 specifications plastic width 27” (68.6cm) plastic thickness 1.5 mil and 3 mil maximum roll length 1.5 mil - 1,000 feet (304.8 meters) 3 mil - 500 feet (152.4 meters) dimensions 20” (50.8cm) l x 35” (88.9) w x 16” (40.6cm) h speed 4.5’ feet per minute (1.4m/minute) net weight 68lbs. (41kg) power re...
Page 6
6 components... The figure below shows the location of the major components and controls of the ez green. You should become familiar with these before operating the laminator. The easy-lam green ™ laminator is designed specifically to provide energy savings to your organization. Easy-lam green ™ sav...
Page 7: Operation
7 timer reset: pressing the auto shutoff shuts the machine down after one hour. The timer reset allows for another hour of use. Standby mode: lowers temperature to 150° cutting energy use in half. Heat control your new easy-lam green ™ has a digital heat controller. Users can easily adjust the set t...
Page 8
8 2. Pull 6"-12" of film from the top roll. Pass the film under the idler bar and over the heat shoes. Make sure the shiny side of the film is against the shoes. 3. For the bottom supply roll, remove the run-off table. From the back of the laminator, place the mandrel ends into position in the lower...
Page 9
9 5. Turn the motor switch to on to start the laminating and pull rollers. 6. Feed a piece of thin cardboard about 10” x 25” against the film so that it is centered between the two heat shoes. Push the cardboard and film into the laminating rollers. See figure 5. 7. When the feed card has completely...
Page 10: Laminating
10 material temperature range 1.5 mil (.0015”) 300°f - 320°f 3 mil (.003”) 250°f - 265°f table 1 laminating 1. Be sure the heaters have been turned on and are at the proper temperature. Be sure the film has been properly threaded. Caution: do not allow the temperature to exceed 350°f as this could c...
Page 11
11 make sure to press “timer reset” if the machine has been unattended for an hour or more. Ensure that the circuit breaker has not tripped fuse may have blown. Replace fuse (rear next to power cord) with 15 amp buss (mda-15) for standard units, or 12 amp (mda-12) for csa units. Problem: laminating ...
Page 12: Maintenance
12 problem: laminated material curls after leaving pull rollers. Action: adjust tension. If laminated item curls upwards, reduce top roller tension. If item curls downward, reduce bottom roller tension. Clean heat shoes of residual adhesive as it may be causing “drag” on one side. Refer to maintenan...
Page 13
13 removing wrap-arounds... When laminating with thinner gauges of film, there is the possibility of the film wrapping around the pull rollers. Use the same procedure for cleaning the heat shoes and laminating rollers in order to remove a wrap-around. You should remove any wrap-arounds that occur as...
Page 14: Parts Lists
14 parts lists item part # description qty 1 1441 roller, ez bottom 2 2 1445 roller, ez top (crown) 2 3 3001 core gripper, ez mandrel 2 4 11327 fuse, 15a fast blow 1 5 11625 fuse holder, 30a power 1 6 1210 heat show ez 2 7 1242 heater, tubular, ez 4 8 645044 motor, ez 1 9 1395 cord, power 14-3 1 10 ...