DL manuals
Eaton
Saw
ET9300-14-220
Instruction Manual

Eaton ET9300-14-220 Instruction Manual - Changing The Blade

Page of 8

Download

Print this page

Bookmark us

Changing the Blade

1. Disconnect Power Plug & logout tagout.

2. Remove hex nuts (right) holding blade

cover and remove cover.

3. Place 1⁄4 rod/pin through arbor shaft to

lock saw blade arbor shaft and drive pin

at 12 o’clock (below left). This will lock the

arbor while the bolt is removed. Please

note that the bolt (below right) to remove

the blade is left hand threaded. To remove

it, turn counter-clockwise.

4. Remove old blade and put new one on over the drive pin (below left) and arbor

shaft. Be sure to follow the blade rotation arrow (below right).

5. Placed clamping flange through drive

pin and bolt blade onto the shaft.

Tighten bolt to 20-25 foot/lbs. Do not

over-tighten. Then remove 1⁄4 rod/pin

which locks shaft.

6. Replace blade cover and tighten hex

bolts.

ROTATION

« ‹ Prev 2 3 4 5 6 7 8 Next › »

Summary of ET9300-14-220

Page 1
Eaton et9300-14-220 hydraulic hose saw instruction manual.
Page 2: Table of Contents
Table of contents introduction ........................ 3 old method ....................... 3 new eaton method ........... 3 operation ........................... 4 operation procedure ........ 4 changing the blade ............ 5 vacuum port ....................... 6 maintenance ......................
Page 3: New Improved Eaton Method
A e d b c new improved eaton method with the eaton hydraulic hose saws the hose is positioned across two pins (a) and moved into the blade (c) by a feed foot (b) using extend- able handle (d) and adjustable pivot point (e) for cutting larger indus- trial hose. The feed motion causes the hose to stre...
Page 4: Operation
Operation this saw is a rugged and dependable tool when used and maintained properly. Many of these saws have been in daily service for years and are still in good working order. As with any tool, good operating procedure is important for tool life and operator safety. Operating procedure 1. Set pin...
Page 5: Changing The Blade
Changing the blade 1. Disconnect power plug & logout tagout. 2. Remove hex nuts (right) holding blade cover and remove cover. 3. Place 1⁄4 rod/pin through arbor shaft to lock saw blade arbor shaft and drive pin at 12 o’clock (below left). This will lock the arbor while the bolt is removed. Please no...
Page 6: Vacuum Port
Vacuum port some saw models have a vacuum port in the cover. You can attach a 2” shop vac hose to this port. The saw “on-off” switch is a double pole switch that you can direct wire the shop vac to. This will allow the operator to start the saw and the vacuum at the same time. A shop vac attached to...
Page 7: Benefits
Benefits • cleaner cuts • safer cuts • no smoke model motor blade cutting capacity et9300-14-220 5 hp, 220 vac, 1 phase, 60 cycle, 3,600 rpm one 14” od x .160 thk x 40 mm arbor 2″ id x 6 wire hydraulic hose — 5″ od industrial hose et9300-14-220-3 3 hp, 220 vac, 3 phase, 60 cycle, 3,600 rpm one 14” o...
Page 8
Eaton hydraulics group usa 14615 lone oak road eden prairie, mn 55344 usa tel: 952-937-9800 fax: 952-294-7722 www.Eaton.Com/hydraulics © 2013 eaton all rights reserved printed in usa document no. September 2013 eaton hydraulics group europe route de la longeraie 7 1110 morges switzerland tel: +41 (0...