- DL manuals
- Eaton
- UPS
- Pulsar Series 1150
- Installation And User Manual
Eaton Pulsar Series 1150 Installation And User Manual
Summary of Pulsar Series 1150
Page 1
Www.Eaton.Com _ installation and user manual evolution 650/650 rack 1u 850/850 rack 1u 1150/1150 rack 1u 1550/1550 rack 1u pulsar series.
Page 2
34008235en/ac - page 2.
Page 3: Introduction
34008235en/ac - page 3 introduction environmental protection eaton has implemented an environmental-protection policy. Products are developed according to an eco-design approach. Substances this product does not contain cfcs, hcfcs or asbestos. Packing to improve waste treatment and facilitate recyc...
Page 4: Introduction
34008235en/ac - page 4 introduction pictograms important instructions that must always be followed. Information, advice, help. Visual indication. Action. Audio signal. In the illustrations on the following pages, the symbols below are used: led off led on led flashing.
Page 5: Contents
34008235en/ac - page 5 contents 1. Presentation 1.1 standard positions ...................................................................................................................... 6 tower models ..................................................................................................
Page 6: 1. Presentation
34008235en/ac - page 6 1. Presentation 1.1 standard positions tower models rack models dimensions (h x w x d) in mm evolution 650 234 x 147 x 418 evolution 850 234 x 147 x 418 evolution 1150 234 x 147 x 418 evolution 1550 234 x 147 x 492 weights in kg evolution 650 8.4 evolution 850 10.8 evolution 1...
Page 7: 1. Presentation
34008235en/ac - page 7 1. Presentation 1.2 rear panels evolution 650/850/1150/1550 evolution 650/850/1150/1550 rack 1.3 control panel bargraphs (8) and (11) (1) slot for optional communication card (2) socket for connection to ac-power source (3) 2 outlets for connection of equipment (4) rs232 commu...
Page 8: 2. Installation
34008235en/ac - page 8 2. Installation 2.1 unpacking and contents check (16) evolution ups, tower or rack model (17) 2 connection cables for the protected equipment (18) documentation (19) solution-pac cd-rom (20) rs232 communication cable (21) usb communication cable (22) mounting kit for 19-inch b...
Page 9: 2. Installation
34008235en/ac - page 9 2. Installation 2.2 installation of tower model 2.3 installation of rack model follow steps 1 to 4 for module mounting on the rails. The rails and necessary hardware are supplied by eaton..
Page 10: 2. Installation
34008235en/ac - page 10 2. Installation 2.4 installation of the 650 rack model follow steps 1 to 3 for rack mounting. The necessary hardware is supplied by eaton..
Page 11: 2. Installation
34008235en/ac - page 11 2. Installation 2.5 communication ports connection of rs232 or usb communication port (optional) installation of the communication cards (optional) characteristics of the contact communication port (optional) the rs232 and usb communication ports cannot operate simultaneously...
Page 12: 2. Installation
34008235en/ac - page 12 2. Installation 2.6 equipment connections check that the indications on the name plate located on the back of the ups correspond to the ac-power source and the true electrical consumption of the total load. 1 - disconnect the supply cable (1) (not supplied) of the equipment. ...
Page 13: 3. Operation
34008235en/ac - page 13 3. Operation 3.1 start-up and normal operation 3.2 operation on battery power transfer to battery power low-battery warning end of battery backup time 3.3 return of ac input power following an outage, the ups restarts automatically when ac input power returns (unless the rest...
Page 14: 3. Operation
34008235en/ac - page 14 3. Operation 3.4 ups shutdown 3.5 ups remote-control functions remote control connection and test press button (10) for approximately 2 seconds. The devices connected to the ups are no longer supplied. Evolution offers a choice between two remote control functions. ◗ rpo (rem...
Page 15
34008235en/ac - page 15 4. Access to measurements and personalisation data main-output personalisation voltage-threshold personalisation (1) low threshold for transfer to battery: 150 v. Ups-sensitivity personalisation ups on/off personalisation battery personalisation ◗ insert the solution-pac cd-r...
Page 16: 5. Maintenance
34008235en/ac - page 16 5. Maintenance 5.1 troubleshooting 5.2 replacing the battery module in the tower model safety recommendations the battery can cause electrocution and high short-circuit currents. The following safety precautions are required before servicing the battery components: ◗ remove w...
Page 17: 5. Maintenance
34008235en/ac - page 17 5. Maintenance mounting the new battery module carry out the above instructions in reverse order. 5.3 replacing the battery module in the rack model safety recommendations the battery can cause electrocution and high short-circuit currents. The following safety precautions ar...
Page 18: 5. Maintenance
34008235en/ac - page 18 5. Maintenance mounting the new battery module carry out the above instructions in reverse order. 5.4 training centre d - pull the plastic tab to remove the battery block and replace it. ◗ to ensure safety and high performance, use only batteries supplied by eaton. ◗ take car...
Page 19: 6. Appendices
34008235en/ac - page 19 6. Appendices 6.1 technical specifications (1) the high and low thresholds can be adjusted using personal solution-pac software. (2) up to 40 hz in extended frequency mode (programmable using personal solution-pac software). (3) adjustable to 200 v (10% derating of output pow...
Page 20: 6. Appendices
34008235en/ac - page 20 6. Appendices 6.2 glossary backup time time during which the load can be supplied by the ups operating on battery power. Battery test internal ups test to check battery status. Booster mode automatic ups mode that steps up the ac voltage if it is too low, to a level above the...
Page 21: Notes
34008235en/ac - page 21 notes.
Page 22
34008235en/ac www.Eaton.Com.