1. DL manuals
  2. Echo
  3. Trimmer
  4. SRM-210U
  5. Operator's Manual

Echo SRM-210U Operator's Manual

Manual is about: Grass Trimmer/Brush Cutter

Summary of SRM-210U

  • Page 1

    Grass trimmer/brush cutter operator's manual model srm - 210u serial number 05001001 - 05999999 warning danger read rules for safe operation and instructions carefully. Echo provides an operator's manual and a safety manual. Both must be read and understood for proper and safe operation. X7702278400...

  • Page 2

    2 i ntroduction welcome to the echo family. This echo product was designed and manufactured to provide long life and on-the-job dependability. Read and understand this manual and the safety manual you found in the same package. You will find both easy to use and full of helpful operating tips and sa...

  • Page 3

    G rass t rimmer /b rush c utter o perator ' s m anual 3 this symbol accompanied by the words warning and danger calls attention to an act or condition that can lead to serious personal injury to operator and bystand- ers. The circle with the slash symbol means whatever is shown within the circle is ...

  • Page 4

    4 shaft decal warning danger • this unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the operator's and safety manuals. • blindness can occur from objects that are thrown or ricocheted even with shield i...

  • Page 5

    G rass t rimmer /b rush c utter o perator ' s m anual 5 s afety i nstructions personal condition and safety equipment warning danger trimmer/brush cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly or safety precautions are not followed. Proper clothing ...

  • Page 6

    6 repetitive stress injuries it is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a repetitive s...

  • Page 7

    G rass t rimmer /b rush c utter o perator ' s m anual 7 safe operation warning danger do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Read the manuals • provide all operators of this equipment...

  • Page 8

    8 d escription your new echo product has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and other final assembly may be necessary. Check the contents carefully, and notify your retailer or echo dealer immediately if any parts are missing or damage...

  • Page 9

    G rass t rimmer /b rush c utter o perator ' s m anual 9 model srm-210u parts 1 2 3 4 5 6 7 8 9 10 14 15 16 17 18 19 20 21 22 12 13 23 11 24.

  • Page 10

    10 1. Power head - includes the engine, clutch, fuel system, ignition system, and recoil starter. 2. Right hand grip 3. Throttle trigger lockout - this lever must be held during acceleration. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged. 4. Stop swi...

  • Page 11

    G rass t rimmer /b rush c utter o perator ' s m anual 11 s pecifications * install and use u-handle when operating any model with blade. Model --------------------------------------------------------------- srm-210u length ----------------------------------------------------------------- 1770 mm (69...

  • Page 12

    12 a ssembly plastic shield installation tools required: screwdriver, locking tool parts required: plastic debris shield, shield plate, three (3) 5 x 16 mm screws. Warning danger the plastic shield is for use with the nylon line head only. Install metal shield when using plastic or metal blades, or ...

  • Page 13

    G rass t rimmer /b rush c utter o perator ' s m anual 13 c b a d g note model srm-210u includes u-handle, 8-tooth blade, and neces- sary blade conversion parts. Blades must be selected for type of cutting being performed. See page 16, "blade selection." install metal shield tools required: 8 x 10 mm...

  • Page 14

    14 install blade tools required: locking tool, scrench. Parts required: upper plate w/ 20 mm pilot, lower plate, 10 mm nut w/ l.H. Threads, 2 x 25 mm cotter pin, blade. 1. Install upper plate (d) on splined pto shaft, pilot side down. Blade installation requires upper plate (d) with 20 mm pilot. 2. ...

  • Page 15

    G rass t rimmer /b rush c utter o perator ' s m anual 15 d e throttle linkage and ignition leads 1. Place throttle linkage cable (c) through adjustment fixture (d) and install wire end into large carburetor throttle swivel hole (e). Check throttle for freedom of movement and that wide open throttle ...

  • Page 16

    16 blade selection warning danger the type of blade used must be matched to the type and size of material cut. An improper or dull blade can cause serious personal injury. Blades must be sharp. Dull blades increase the chance of kick out, and injury to yourself and bystanders. Plastic/nylon blades m...

  • Page 17

    G rass t rimmer /b rush c utter o perator ' s m anual 17 shoulder/waist harness (p/n 30100052131) use of the shoulder/waist harness is required for blade operation, and is recommended for all trimmer/brush cutter use. The shoulder/waist harness suspends the trimmer from the operator's shoulder, and ...

  • Page 18

    18 important spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. Contact your echo dealer for ordering information. After refueling • wipe any spilled fuel from the unit. • move at least 3 m (10 ft.)...

  • Page 19

    G rass t rimmer /b rush c utter o perator ' s m anual 19 o peration starting cold engine warning danger the cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "carburetor adjustment" instructions in this manual or see your echo dealer, otherwise ser...

  • Page 20

    20 starting warm engine warning danger the cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "carburetor adjustment" instructions in this manual or see your echo dealer, otherwise serious personal injury may result. 1. Stop switch move stop switch ...

  • Page 21

    G rass t rimmer /b rush c utter o perator ' s m anual 2 1 maintenance intervals / t n e n o p m o c m e t s y s e c n a n e t n i a m e r u d e c o r p d ' q e r l l i k s l e v e l r o y l i a d e r o f e b e s u y r e v e l e u f e r 3 s h t n o m 0 9 r o s r u o h 6 s h t n o m 0 7 2 r o s r u o ...

  • Page 22

    22 air filter level 1. Tools required: 25-50 mm (1 or 2 in.) medium bristle paint brush. Parts required: 90030 repower tm air & fuel filter kit. 1. Close choke (cold start position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumu- lated dirt from ...

  • Page 23

    G rass t rimmer /b rush c utter o perator ' s m anual 23 spark plug level 2. Tools required: scrench (combination socket wrench & screw driver) feeler gauge, preferably a wire gauge. Brush. Parts required: repower tm tune-up kit p/n 90074 1. Remove spark plug and check for wear or fouling. 2. Clean ...

  • Page 24

    24 4. Use the wooden stick or brush to remove dirt from the cylinder fins. 5. Install engine cover properly, placing fuel vent tube into engine cover and deflector shield tabs (a) into slots in engine cover. 6. Secure engine cover with three (3) screws. 7. Install top guard, and secure with one (1) ...

  • Page 25

    G rass t rimmer /b rush c utter o perator ' s m anual 25 a carburetor adjustment note new engines must be operated for a minimum of two tanks of fuel before carburetor adjustments can be made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle...

  • Page 26

    26 a lubrication level 1. Tools required: 8 mm open-end wrench, screwdriver, clean rag. Parts required: echo ® lube tm 8 oz. (p/n 91014) or lithium base grease. Gear housing 1. Clean all loose debris from gear box. 2. Remove plug (a) and check level of grease. 3. Add grease if necessary. Do not over...

  • Page 27

    G rass t rimmer /b rush c utter o perator ' s m anual 27 nylon line replacement level 1. Parts required: echo 0.095" nylon trimmer line 6 m (20 ft.) long. 1. Shut engine off. Lay unit on the ground with head assembly up. 2. Hold drum (a) and turn spool (b) cw (clockwise) until it stops. Pull spool f...

  • Page 28

    28 8. Hold drum (a) firmly and turn spool (b) ccw (counterclockwise) until it stops. Do not push in on spool when turning. 9. Pull both lines out and trim to cut-off knife length. Sharpening metal blades three styles of metal blades are approved for use on the echo brush cutter. The 8-tooth blade ca...

  • Page 29

    G rass t rimmer /b rush c utter o perator ' s m anual 29 t r a h c g n i t o o h s e l b u o r t m e l b o r p e n i g n e m e l b o r p k c e h c s u t a t s e s u a c y d e m e r e n i g n e - s k n a r c / d r a h s t r a t s t ' n s e o d t r a t s r o t e r u b r a c t a l e u f t a l e u f o n...

  • Page 30

    30 s torage warning danger during operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long term storage (over 30 days) d...

  • Page 31: Notes

    G rass t rimmer /b rush c utter o perator ' s m anual 31 notes.

  • Page 32

    Echo, incorporated 400 o akwood r oad l ake z urich , il 60047-1564 www.Echo-usa.Com dealer? Call 1-800-432-echo or www.Echo-usa.Com consumer product support 1-800-673-1558 8:30 - 4:30 mon - fri c.S.T. S ervicing i nformation parts genuine echo parts and echo repower™ parts and assemblies for your e...