1. DL manuals
  2. Echo
  3. Trimmer
  4. SRM-211
  5. Operator's Manual

Echo SRM-211 Operator's Manual

Manual is about: Grass trimmer/brush cutter

Summary of SRM-211

  • Page 1

    Grass trimmer/brush cutter operator's manual model srm-211 srm-211u serial number 002001001 - 02999999 warning danger read rules for safe operation and instructions carefully. Echo provides an operator's manual and a safety manual. Both must be read and understood for proper and safe operation. X770...

  • Page 3

    G rass t rimmer /b rush c utter o perator ' s m anual 3 the circle with the slash symbol means whatever is shown within the circle is prohibited. M anual s afety s ymbols and i mportant i nformation important the enclosed message provides information necessary for the protection of the unit. Note th...

  • Page 4

    4 shaft decal warning danger • this unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the operator's and safety manuals. • blindness can occur from objects that are thrown or ricocheted even with shield i...

  • Page 5

    G rass t rimmer /b rush c utter o perator ' s m anual 5 equipment before operation a complete check of the unit must be performed; • check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. • inspect fuel lines, tank and area around carburetor for fuel leaks. Do not ope...

  • Page 6

    6 fuel warning danger fuel is very flammable. Use extreme care when mixing, storing or handling, or serious personal injury may result • use an approved fuel container. • do not smoke near fuel. • do not allow flames or sparks near fuel. • fuel tanks/cans may be under pressure. Always loosen fuel ca...

  • Page 7

    G rass t rimmer /b rush c utter o perator ' s m anual 7 eye protection -- wear eye protection that meets ansi z87.1 or ce requirements whenever you operate the trimmer. Hand protection -- wear no-slip, heavy duty work gloves to improve your grip on the trimmer/brush cutter handles. Gloves also reduc...

  • Page 8

    8 safe operation determine operation area • provide all operators of this equipment with the operator's manual and instructions for safe operation. • review the area to be trimmed. Look for hazards that could contribute to unsafe conditions. • spectators and fellow workers must be warned, and childr...

  • Page 9

    G rass t rimmer /b rush c utter o perator ' s m anual 9 vibration and cold -- it is believed that a condition called raynaud’s phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and bu...

  • Page 10

    10 d escription the echo product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or echo dealer of damaged or missin...

  • Page 11

    G rass t rimmer /b rush c utter o perator ' s m anual 11 important engine information engine family: yehxs.0214ca displacement: 21.2 cc this engine meets u.S. Epa ph1 and 2000 and later california emission regulations for s.O.R.E. Refer to owner's manual for maintenance specifications and adjustment...

  • Page 12

    12 1 2 3 4 5 6 7 8 9 10 11 17 19 20 21 3 7 12 13 14 15 16 18 22 23 24 25 26 5 11.

  • Page 13

    G rass t rimmer /b rush c utter o perator ' s m anual 13 1. Operator's manual - included in plastic bag (co-pack). Read before operation and keep in a safe place for future reference, i.E., operation, maintenance, storage and specifications. 2. Safety manual - included in plastic bag (co-pack). Read...

  • Page 14

    14 s pecifications * install and use u-handle when operating any model with blade. Mod e l s r m-211 s r m-211u length 1770 mm (69.7 in.) w idth 245 mm (9.65 in.) 680 mm (26.8 in.) height 225 mm (8.86 in.) 415 mm (16.3 in.) w eight (dry) w/cutter head 5.3 kg (11.6 lb.) 5.75 kg (12.7 lb.) e ngine typ...

  • Page 15

    G rass t rimmer /b rush c utter o perator ' s m anual 15 plastic shield installation (for nylon line operation) tools required: screwdriver. Parts required: plastic shield, shield plate, three (3) 5mm x 15mm screws. Note the plastic shield is for use with the nylon line head only. Install metal shie...

  • Page 16

    16 blade installation all models. Important if non-standard monofilament head, metal/plastic blade or cultivator etc. Is used, the carburetor must be re-set or serious engine damage may occur. See "carburetor adjustment" pages 32 - 33 and "specifications" page 14 of this manual. Install metal shield...

  • Page 17

    G rass t rimmer /b rush c utter o perator ' s m anual 17 install harness clamp note some models require installation of harness clamp. If your unit does not have a clamp, follow these directions. Tools required: screwdriver, 8mm x 10mm open end wrench. Parts required: clamp, 4mm x 18mm hexagon head,...

  • Page 18

    18 front handle installation (srm-211) tools required: screwdriver. 1. Position front handle for comfortable operation and secure screws. U - handle installation tools required: 8mm x 10mm open end wrench, slotted screwdriver, (3mm hex wrench srm-211 only.) parts required: u-handle kit. (srm-211) p/...

  • Page 19

    G rass t rimmer /b rush c utter o perator ' s m anual 19 7. Position lower u-handle bracket (k) 400mm (15-3/4 in.) from engine end of drive shaft. Secure with three (3) 5mm x 30mm bolts. 8. Install harness hook (included with blade conversion kit) for blade use. Position 220 mm (8-5/8 in.) from engi...

  • Page 20: - O

    20 choosing the correct blade warning danger the type of blade used must be matched to the type and size of material cut. An improper or dull blade can cause serious personal injury. Blades must be sharp. Dull blades increase the chance of kick out and injury to yourself and bystanders. Plastic and ...

  • Page 21

    G rass t rimmer /b rush c utter o perator ' s m anual 21 plastic/nylon blades may be used where ever the nylon line head is used. Do not use this blade for heavy weeds or brush! 8 tooth weed/grass blade p/n 69600120331 is designed for grass, garden debris and thick weeds. Do not use this blade for b...

  • Page 22

    22 fuel fuel requirements gasoline - use 89 octane [ ] gasoline or gasohol known to be good quality. Gasohol may contain up to 10% ethyl (grain) alcohol or 15% mtbe (methyl tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is not approved. Two stroke oil - a two-stroke engine oil meeti...

  • Page 23

    G rass t rimmer /b rush c utter o perator ' s m anual 23 storage - fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, air tight container. Store in a well ventilated, unoccupied building, away from sparks an...

  • Page 24

    24 determine operation area • review the area to be trimmed. Look for hazards that could contribute to unsafe conditions. • spectators and fellow workers must be warned, and children and animals prevented from coming nearer than 15 m (50 ft.) while the trimmer is in use. O peration • provide all ope...

  • Page 25

    G rass t rimmer /b rush c utter o perator ' s m anual 25 starting cold engine warning danger the cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "carburetor adjustment" instructions in this manual or see your echo dealer, otherwise serious person...

  • Page 26

    26 starting warm engine the starting procedure is the same as cold start except do not close the choke. Warning danger the cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "carburetor adjustment" instructions in this manual or see your echo dealer...

  • Page 27

    G rass t rimmer /b rush c utter o perator ' s m anual 27 m aintenance your echo trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to t...

  • Page 28

    2 8 maintenance intervals / t n e n o p m o c m e t s y s e c n a n e t n i a m e r u d e c o r p d ' q e r l l i k s l e v e l r o y l i a d e r o f e b e s u y r e v e l e u f e r 3 s h t n o m 0 9 r o s r u o h 6 s h t n o m 0 7 2 r o s r u o h y l r a e y 0 0 6 s r u o h s e r u d e c o r p e c ...

  • Page 29

    G rass t rimmer /b rush c utter o perator ' s m anual 29 air filter level 1. Tools required: 25 - 50 mm (1 - 2 in.) cleaning brush parts required: 90008 repower tm air & fuel filter kit. 1. Close choke (cold start position). This prevents dirt from entering the carburetor throat when the air filter ...

  • Page 30

    30 warning danger catalytic mufflers operate at extremely high temperatures. Muffler area must be kept clean. Do not perform maintenance on the muffler until engine and muffler are completely cool, otherwise serious personal injury may occur. Spark plug level 2. Tools required: scrench (combination ...

  • Page 31

    G rass t rimmer /b rush c utter o perator ' s m anual 31 1. Remove spark plug lead 2. Loosen outer throttle cable nut (a) and remove cable from engine housing bracket slot. 3. Remove two (2) engine cover screws at top of starter. 4. Remove screw and arm rest (b). Lift cover (c) from engine. 5. Use t...

  • Page 32

    32 carburetor adjustment engine break-in new engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as requi...

  • Page 33

    G rass t rimmer /b rush c utter o perator ' s m anual 33 note every unit is run at the factory and the carburetor is set in compli- ance and california emission regulations. In addition, the carbure- tor is equipped with a hi needle adjustment limiter that prevents settings outside acceptable limits...

  • Page 34

    34 lubrication level 1. Tools required: 8 mm open end wrench, cross head screwdriver, clean rag parts required: echo lube tm 8 oz. (p/n 91014) or lithium base grease. Gear housing 1. Clean all loose debris from gear box. 2. Remove plug (a) and check level of grease. 3. Add grease if necessary, do no...

  • Page 35

    G rass t rimmer /b rush c utter o perator ' s m anual 35 nylon line replacement level 1. Tools required: head locking tool (if head is to be removed) parts required: echo 0.095" nylon trimmer line 12m (40 ft.) long. 1. Hold drum (a) and turn spool (b) cw (clockwise) until it stops. Pull spool from d...

  • Page 36

    36 3. Hold the spool, opening toward you. Place index finger between the two strands and wind line, tightly and evenly, in direction of arrow marked "cc". 4. Stop when approximately 15-20 cm (6-8 in.) line (c) remains and place ends of line in notches (e) in spool (b). 5. Feed ends of line through h...

  • Page 37

    G rass t rimmer /b rush c utter o perator ' s m anual 37 sharpening metal blades three styles of metal blades are approved for use on the echo brush cutter. The 8-tooth blade can be sharpened during normal mainte- nance. The clearing blade and 80 tooth blade require professional service. Before shar...

  • Page 38

    38 t roubleshooting problem engine -- starts hard engine -- does not start cause remedy engine cranks fuel at carburetor no fuel at carburetor fuel strainer clogged fuel line clogged carburetor clean clean see your echo dealer fuel at cylinder no fuel at cylinder carburetor see your echo dealer muff...

  • Page 39

    G rass t rimmer /b rush c utter o perator ' s m anual 39 s torage long term storage (over 30 days) warning danger during operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise se...

  • Page 40

    S ervicing i nformation parts genuine echo parts and echo repower tm parts and assemblies for your echo products are available only from an authorized echo dealer. When you do need to buy parts always have the model number and serial number of the unit with you. You can find these numbers on the eng...

  • Page 41: Supplement To Operator'S

    * some echo units may be factory pre-assembled. The nylon line head, plastic debris shield, and mounting hardware shown in the contents list are pre-assembled to the unit. No assembly tools are needed. The front handle may need to be re-positioned for comfortable operation. Suplemento del manual del...

  • Page 42

    99922203541 01/02 sup22203541 supplement to operator's manual part number x7702272400 (x770000180) for models: srm-211 /u s/n 02001101 & up suplemento del manual del operador numero de pieza 7702272400 (x770000180) para los modelo: srm-211 /u s/n 02001101&up e mission control california tier 2 the e...