Summary of eMOTUS5P
Page 1
Emotus5p/emotus5pb surface mount cabine ts powered loudspeakers - stereo kit user manual.
Page 2
2 index important note 3 precautions 3 introduction 4 key features 4 positioning and fitting 5 start up 7 remote control 8 rear panel 10 technical specifications 11 packing content 12.
Page 3
3 im p o r ta nt n ote congratulations. You now own the result of a well-designed, carefully produced manufacture. We thank you for your trust by having chosen our set of powered emotus5p/emotus5pb acoustic cabinets. To achieve its maximum working order and performance, it is very important, before ...
Page 4
4 int r od u c t i o n the emotus5p / emotus5pb is a kit of loudspeakers including an active and a passive acoustic box. The emotus5pb includes a wireless bt receiver, remote control and remote control volume port (0-10 vdc). A compact, professional stereo kit, easy to handle and at a very attractiv...
Page 5
5 po s it io ni n g a nd fi tt in g in the packing of the emotus systems, you will find all you need to complete installation of the two units. The following should be observed as general rules: always install on solid, firm surfaces. For good sound reproduction, there should be no hindrance between...
Page 6
6 5. Connect the power supply cables, signal input and link between the two units to the connectors on the rear part of the housing. Ensure correct polarity in the euroblock terminals. 6. Place the acoustic box in its final position, sliding it vertically downwards so that the rear side of the rail ...
Page 7
7 st a rt u p emotus5p to start up the system, turn on the master (l) unit with the switch on the rear panel and adjust the volume and equalizer to the required settings. You may select the audio source (balanced or non-balanced input) by pressing the rotating volume encoder. Emotus5pb to start up t...
Page 8
8 re m o te c o nt r o l remote control (only applies to the emotus5bt model) º 1. Turn on: on/off. The green led display lights up when the unit is on. When off, no led is displayed. 2. Led display: turn on/off the leds while the unit is operating. When restarting the unit, this function returns to...
Page 9
9 10. Auto standby: keep pressed (for 2 secs.) to activate/deactivate the auto standby function. If this is activated, after 2`30” with no audio in the inputs and if the remote controlled is not used, the unit will switch to standby mode. 11. Reset: keep pressed (for 2 secs.) to reset the system to ...
Page 10
10 re a r p a ne l 1. Output volume control 2. Bass control 3. Treble control 4. Stereo-mono switch 5. Remote input rj-45. Only applies to the emotus5bt model 6. Balanced audio input - euroblock connectors 7. Non-balanced audio input – rca connectors 8. Attachment point for the safety cable 9. Socke...
Page 11
11 te c h n ic a l s p e c i f ic a ti o ns emotus5pb / emotus5p power 2 x 25w rms impedance 8 Ω frequency response (±10db) 85hz – 20khz thd + noise @ 1khz full pwr ≤0.5% inputs sensitivity nom/impedance 525mv/22k Ω cmrr - line bal ≥80db tone control response ±14db mains voltage 115 / 230vac (select...
Page 12
12 pa c ki ng c on te n t emotus5p / emotus5pb loudspeaker kit (one active unit + one passive unit) 2 x articulated brackets for wall mounting 5mm allen key 2 x metal safety lines against any possible flaking off, with corresponding screws and lock washers. 2 x euroblock connectors with three termin...
Page 13
13 all product characteristics are subject to variation due to production tolerances. Neec audio barcelona s.L. Reserves the right to make changes or improvements in the design or manufacturing that may affect these product specifications. Motors, 166‐168 08038 barcelona ‐ spain ‐ (+34) 932238403 in...