Summary of TRAIL103
Page 1
Trail103 acoustic cabinets lighting rail mount loudspeaker user manual.
Page 2: Contents
2 contents important note 3 precautions 3 introduction 4 main features 4 connecting 4 location and fitting 6 technical specifications 13 packaging content 13.
Page 3: Important
3 important note congratulations. You now own the result of a well-designed, carefully produced manufacture. We thank your for your trust by having chosen our trail 103 lighting rail mount loudspeaker. To achieve its maximum working order and performance, it is very important, before connecting, to ...
Page 4: Introduction
4 introduction trail103 is a 3” loudspeaker with the appearance of a lamp. It is fitted with a three- fold installation system: in lighting rail, on a surface and using an adapter for a truss or threaded bar. It includes connections for low impedance (4 ohm) and for high impedance (15w and 30w). Ava...
Page 5
5 the 100v line connector makes it possible to set the maximum power with which each unit will operate. So in areas where a low noise level is required, the 0 and 15w terminals are used to connect the loudspeaker, while in areas here a higher level is required, the 0 and 30w terminals are used. Note...
Page 6: Location
6 location and fitting the trail1o3 offer different fitting systems. Included in the packing you will find all the accessories needed for the different options: installation on a lighting rail, on a surface (wall or ceiling) and in a threaded bar or truss. The following rules should be followed: • a...
Page 7
7 4. Place the side covers threading the audio cable through the hole made. Exert slight pressure on the covers until they are firmly in place. 5. Connect up the loudspeaker. Consult the chapter “connecting” for further details. 6. Fit the rear cover. 7. Place the loudspeaker on the lighting rail, a...
Page 8
8 8. Ensure that the adapter wheel is in the off position. Rotate the safety lug to secure the loudspeaker on the lighting rail. Rotate the wheel until in a position other than off and the safety lug will be blocked. 9. Orientate the loudspeaker to obtain the required position on the vertical and ho...
Page 9
9 2. Thread the audio cables through the hole in the base. This is fitted with a socket inside the base to ease making connections (optional). 3. Attach the base to the surface. Make sure that the surface is solid and firm. To this end, it has 4 holes. It is advisable to use Ø 4mm screws (not includ...
Page 10
10 6. Insert the attachment for the loudspeaker arm on the previously installed based, in line with the following illustration. 7. Attach the cover to the base. To do so, apply pressure to the cover against the base so that the groove and lugs are in line. You will hear a click when it is attached..
Page 11
11 8. Orientate the loudspeaker to obtain the required position with the vertical and horizontal axes. Procedure for installing on a truss or threaded bar: 1. Remove the lighting rail mounting accessory. To do so, remove the attachment screws, as shown in the illustration. Also remove the washer and...
Page 12
12 2. Secure the mounting accessory on the threaded bar or truss, as shown in the illustration below. 3. Make the connections. Follow steps 1 to 6 as detailed in the previous section: installing on lighting rail. 4. Secure the loudspeaker on the threaded bar or truss and orientate the loudspeaker un...
Page 13: Technical
13 technical specifications ways 1 driver diameter 3” rms power 30 w power connections lo- z: 4Ω; hi -z: 15/30 w @ 100v input impedance 4Ω/667 Ω /333 Ω high frequency response 20 khz sensitivity 1w/1m 83 db dimensions (without arm) Ø96mm x 110mm fixing system 4 wire 3 circuit rail system support arm...