Eclipse ACC970 Instruction Manual - Lcd Access Controller
V110519
LCD Access Controller
Metal Case / Standard
Enter program mode → Add/Delete → Antipass Group →
Input Start address → Input End address → 1: Yes; 2: No;(select one)
1
9
Card set-up
Usually, anti-pass back is commonly applied to parking lots in order to prevent from multi-entry with one card, requires to set bith card and device
as the flowings:
F. Anti-Pass Back(M4/M8 only)
Device set-up
Enter program mode → Parameters[2] → Anti-pass back →
1: Yes; 2: No;(select one) → 1: In; 2: Out;(select one)
4
7
G. Lift Control
Connect with
ACC1040 to control which floors the user will be able to access.
Set Floor
1
0
17
0
9
0
25
0
1
2
3
0
19
0
11
0
27
0
2
0
18
0
10
0
26
0
4
0
20
0
12
0
28
0
5
0
21
0
13
0
29
0
6
0
22
0
14
0
30
0
7
0
23
0
15
0
31
0
8
1
24
0
16
1
32
0
Enter program mode → Tools → Termingal Port →
1:ACC1040
5
4
Setting Lift control
Enter program mode → User Setting → Single Floor →
Input 5-digit user address → Input single floor number: 1~32
2
4
Single floor set-up
Enter program mode → User Setting → Single Floor →
Input 5-digit user address → Select range: 1 or 2 → Input 16 digits multi floors
number [0:disable, 1: enable]
[e.g.] Set NO. 114, to access the 8th and the 16th floors.
Enter program mode → User Setting → Single Floor →
114 → 1 → 0000000100000001
2
2
5
5
Multi floors set-up
H.Arming Mode
Conditions:
1.Arming is enabled
2.Alarm system connected
Application:
1. Door left open warnings: these are generated when the door is held open for longer than the lock relay time and door
open time.
2. Force open (Unauthorized access alarms): these are generated when a door is opened without a valid card being
presented or a request to exit signal being received.
3. Door contact error: when the controller in arming status and power failure, reset power may activate alarm system.
Manu Tree
5. Tools
1. Language
2. Master Code
3. Master Range
4. Terminal Port
5. ACC1040 Node
6. Open Time Zone
7. Information
8. Clock Setting
9. Control Mode
0. View Events
6. Quit
7. Quit & Arming
4. Parameters[2]
1. Auto Relock
2. Egress(R.T.E)
3. Attendance
4. Master Node
5. Force Open
6. Close & Stop
7. Anti-pass-back
8. Duress Code
9. Factory Reset
0. Key (#) is Bell
3. Parameters[1]
1. Node ID
2. Auto open Zone
3. Door Relay Tm
4. Door Close Tm
5. Alarm Relay Tm
6. Alarm Delay Tm
7. Arming Delay Tm
8. Arming PWD
9. Arming Pulse
0. Auto Alarm Tm
2. User Settings
1. Password
2. Access Mode
3.Extend Options
4. Single Floor
5.Multi Floor
1. Add/ Delete
1. Add Card >ID
2. Add > RF Learn
3. Suspend > Address
4. Suspend > ID #
5. Delete > Address
6. Delete > ID #
7. Recover > Address
8. Recover > ID #
9. Antipass Group
Enter program mode → Tools → Control Mode →
1:M4, 2:M6, 3:M8 (refer to following table) → Succeeded
5
9
E.Control Mode (M4/M6/M8)
※
The users up to 65,535 in
Mode 6, since it reads CARD CODE(5 digits) only, unlike that Mode4/Mode8 read SITE CODE and CARD CODE(10 digits).
Mode
Networking/
Standalone
Standalone
Networking/
Standalone
Networking/
Standalone
User
Capacity
Access Mode
M4
M6
M8
Yes
No
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
Yes
32
No
32
11
No
11
1,200
(950)
1,500
(970)
No
1,200
(950)
1,500
(970)
1,024
(950)
3,000
(970)
65,535
1,024
(950)
3,000
(970)
Auto-show
Duty time
Event log
Capacity
120
Holidays
Anti
force
Time
Zone
Lift
Control
Anti-pass
back
1.Card only
2.Card and PIN
(4-digit PIN)
3.Card or User address
(5-digit)
+ Individual PIN
(4-digit individual PIN)
1.Card only
2.Card and PIN
(4-digit public PIN= Arming PWD)
3.Card or PIN
(4-digit public PIN= Duress code)
1.Card only
2.Card and PIN
(4-digit individual PIN)
3.Card or PIN
(4-digit individual PIN)
7
Enter program mode → Quit
6
Enable/Disable Arming Mode:
Enable Arming Mode
Disable Arming Mode
Program Mode
Door Open
Door Close
Access Mode →
Input 4 digit arming code →
→
Input 4 digit arming code → Present the card to the controller reader
→
Input 4 digit arming code → Present the card to the controller reader
Access Mode →
Input 4 digit arming code →
Enter program mode → Quit & Arming