Eclipse AVN6000 Installation Manual

Other manuals for AVN6000: User Manual

Summary of AVN6000

  • Page 1

    Be sure to read this installation manual thoroughly prior to installation and making connections. If installation methods or non-standard parts not specified in this installation manual are used, accidents or injury may result. Professional installation is recommended, contact the place of purchase ...

  • Page 2: Tip

    - 2 - components components check that all of the following components are present check that all of the following components are present gps antenna components gps antenna x 1 12 waterproof cushion x 1 13 earthing plate x 1 14 body protective sheet x 1 15 when installing the main unit, some vehicle...

  • Page 3: Tip

    - 3 - warnings and caution signs, illustrated below, are posted throughout this manual as well as on the avn6000. They show safe and correct ways to handle the main unit to prevent personal injury to you and others and avoid damage to property. Before reading through the manual, take time to read th...

  • Page 4

    - 4 - • • this main unit must be operated only as an on-board main unit, or it may cause electrical shock or injury. • • do not play distorted sounds for long periods of time; the speakers may overheat and cause a fire. • • once installation and wiring have been completed, return the brakes and elec...

  • Page 5: Tip

    - 5 - installation diag installation diag r r am am gps antenna (when installing inside the vehicle) 12 gps antenna (when installing outside the vehicle) 12 • • if installing the gps antenna inside the vehicle, the location and the slope of the vehicle's windscreen will determine the accuracy of the...

  • Page 6: Tip

    Interconnecting wires (speed pulse, parking brake, reverse) - 6 - • • never cut the insulation on the power wire or use it to power any other equipment. If the rated current capacity of the power wire is exceeded, fire and electric shocks may result. • • the wires should be secured with tape or a si...

  • Page 7: , And

    - 7 - wire colours and connection points for interconnecting wires , , , , , and 7 6 5 4 3 2 never connect the power supply to the speaker wires (no.6 and no.7), otherwise it will cause damage to the main unit. Caution b+ (yellow) connect where power is constantly available, regardless of the igniti...

  • Page 8: Main Unit Connections

    - 8 - vcr output terminals connect to a monitor with video input. Yellow : video signal white : audio(left) signal red : audio(right) signal vcr input terminals connect to the output wire of an external video main unit such as a vcr. Yellow : video signal white : audio (left) signal red : audio (rig...

  • Page 9: Tip

    - 9 - vehicle component adapter wires vehicle harness from main unit - example of using vehicle adapter wires - - vehicle connections - power supplies for combined equipment • • you will need to purchase the necessary vehicle component adapter wire for the vehicle so that the power supplies can be u...

  • Page 10: Notes On Installation

    - 10 - notes on installation • • check the vehicle speed pulse signal, parking brake signal, and reverse signal carefully before making the connections. If the wires are incorrectly connected, accidents or problems with correct operation may result. • • the label on the vehicle speed pulse signal wi...

  • Page 11: Tip

    Route the parking brake signal wire to the main unit. - 11 - foot-operated parking brake hand-operated parking brake - connecting point for parking brake signal (example) - attach a splicing connector at this location. Reverse signal wire reverse lamp reverse signal wire - connecting point for rever...

  • Page 12: Tip

    - 12 - system connection e system connection e xample xample • • install and connect all of the peripheral units before connecting them to the main unit. • • do not remove any of the protective caps (rca, etc.) unless in use. • • be sure to wrap the interconnecting wires with tape (pvc tape) to insu...

  • Page 13: Tip

    - 13 - tip installing the gps antenna installing the gps antenna notes on installation • • do not install the antenna in places (such as front pillars and roof panel) that are shielded from the sky. • • the gps antenna should be installed in a level position where the signals will be as unobstructed...

  • Page 14: Tip

    - 14 - - installation inside the vehicle (example) - choose an installation location on the dashboard which is flat and has a clear view of the sky. 1 install the earthing plate to the dashboard. 2 install the gps antenna to the earthing plate. 3 earthing plate 12 secure the gps antenna. 4 route the...

  • Page 15: Tip

    - 15 - - installation outside the vehicle (example) - choose an installation location where the gps antenna can be attached securely. 1 remove the backing paper from the body protective sheet and attach the sheet to the vehicle. 2 install the gps antenna on top of the body protective sheet. 3 body p...

  • Page 16: Tip

    Remove the pocket and any other accessories from the centre cluster to make room for the main unit. 1 remove the mounting brackets for the pocket. 2 attach the brackets to the main unit. 3 install the main unit in the vehicle. 4 be careful not to forcefully push on the main unit's display or buttons...