Eclipse CB1 Installation Manual

Other manuals for CB1: Brochure
Manual is about: CEILING BRACKET

Summary of CB1

  • Page 1

    • • be sure to read this installation manual thoroughly prior to installation. • • if installation methods or non-standard parts not specified in this installation manual are used, accidents or injury may result. • • specialized techniques and expertise are required in order to install the speaker t...

  • Page 2: Anese

    Accessor accessor ies ies t t ools used ools used have the following tools ready before commencing installation work. Have the following tools ready before commencing installation work. 6 – 2 – ja p anese english g erman f rench it alian s p anish • • phillips screwdriver (plus tip) cb1 components s...

  • Page 3: Anese

    – 3 – the following warning and caution signs are used throughout this manual as well as on the product. These signs alert the installer and users of important safety information to avoid risk of injury and damages to the product. Please become familiar with these symbols and their associated inform...

  • Page 4: Anese

    – 4 – ja p anese english g erman f rench it alian s p anish be sure to leave some space in between the speaker and the wall so that the speaker and wall do not touch. Base cover speaker base leave enough space. Speaker bracket 2 spacer 1 ceiling wall speaker wire (for diameter of 7 mm or more) speak...

  • Page 5: Anese

    – 5 – ja p anese german french it alian s p anish english remove the speaker from the speaker base. (for td508 ii only) 4 remove the base cover. 2 base cover speaker remove the hexagon head screw which is used for securing the base cover drop-prevention wire from the speaker. 3 for the td510, do not...

  • Page 6: Anese

    – 6 – ja p anese english g erman f rench it alian s p anish speaker remove the neck holding bolt at the base of the speaker. 7 neck holding bolt use the allen key which is supplied with the speaker to loosen the angle adjustment screw underneath the speaker. 8 speaker angle adjustment screw allen ke...

  • Page 7: Anese

    – 7 – ja p anese german french it alian s p anish english • • the tabs on the joint of the speaker base should fit into the slots in the speaker as shown in the illustration. If the tabs are not inserted into the slots, the speaker will not be fully secured and it may fall down and damage may result...

  • Page 8: Anese

    – 8 – ja p anese english g erman f rench it alian s p anish peel off the backing paper from the double-sided tape on the spacer, and attach the spacer to the bracket. 15 install the bracket at the speaker installation position using the screws (sold separately). 16 • • install the bracket securely s...

  • Page 9: Anese

    – 9 – ja p anese german french it alian s p anish english connect the speaker wires to the speaker. 18 align the projections on the speaker with the slots in the bracket. 19 turn the speaker to hook the projections on the speaker into the bracket to secure the speaker. 20 speaker wire speaker wire s...

  • Page 10: Anese

    – 10 – ja p anese english g erman f rench it alian s p anish wire 3 securely install the speaker to the bracket by using the stubby screwdriver to tighten the screws. 21 speaker bracket 2 install the drop-prevention wire to the ceiling. 22 screw x4 4 install the drop-prevention wire to the ceiling i...

  • Page 11: Anese

    – 11 – ja p anese german french it alian s p anish english base cover speaker install the base cover to the speaker base. 24 base cover speaker install the base cover drop-prevention wire to the speaker base by carrying out step in reverse. 23 drop-prevention wire hexagon head screw 3 drop-preventio...

  • Page 12: Anese

    TD508Ⅱ TD510 99mm 193mm – 12 – ja p anese english g erman f rench it alian s p anish – template for determining bracket installation position – route the speaker wires before installing the spacer and the bracket to the ceiling. (bracket installation hole diameter: 7 mm) front of speaker (standard p...