- DL manuals
- Ecobee
- Thermostat
- SMART
- Installation Manual
Ecobee SMART Installation Manual
Summary of SMART
Page 2
Getting started 2 welcome 2 technical support 2 before you begin 3 hvac system compatibility information 3 fcc compliance statement 4 specifications 5 installing the ecobee smart thermostat 7 installing the equipment interface 7 wiring the equipment interface 8 wiring diagrams 9 installing the smart...
Page 3
Getting started welcome thank you for supporting ecobee, the smart thermostat that provides your customers with freedom and flexibility in managing their home environment. The ecobee smart thermostat has been designed in partnership with hvac contractors to ensure the installation process is simple ...
Page 4
Before you begin this product is intended to be installed by trained service professionals this manual explains the procedures for installing the ecobee smart thermostat. Please read it carefully before beginning the installation. For information on how to operate the ecobee smart thermostat, please...
Page 5
Reorient or relocate the receiving antenna increase the separation between the equipment and receiver connect the equipment to an outlet on a different circuit from the receiver consult the dealer or an experienced radio/tv contractor for help. Warning: changes or modifications not expressly approve...
Page 6
Installing the smart thermostat there are five steps to installing the ecobee smart thermostat step 1 : install the equipment interface. Step 2: wire the equipment interface. Step 3: i nstall the smart thermostat. Step 4: connect the smart thermostat to the equipment interface. Step 5: power up both...
Page 7
Wiring diagrams below are the equipment interface terminal labels please take note that there is a factory installed jumper between r/h and r/c. 9 installing the smart thermostat installing the smart thermostat 10 d- d+ gnd +12v in2- in2+ in1- in1+ y w o/b g w2 aux r/h r/c nc nc acc1 acc1r acc2 acc2...
Page 10
4. Move the backplate out of the way and make holes where indicated in step 3. The mounting holes can accommodate a #6 pan-head screw. 5. Use drywall plugs or other screw anchors (not included) to ensure the smart thermostat can be mounted securely to the wall. 6. Fasten the backplate to the wall us...
Page 11
The thermostat comes with a factory installed, coin cell battery. When replacing the battery ensure the + side of the battery is facing out and the battery contacts remain in the upright position (not bent underneath the battery). The battery should snap in easily. Connecting power once you’ve compl...
Page 12
Navigating the smart thermostat once the smart thermostat and equipment interface are powered up and working correctly, you can begin configuring the system. The smart thermostat uses touch screen technology, so it’s easy to navigate – just tap the icons, buttons and lists. Note: to prevent damage t...
Page 13
Min cycle off time enables you to configure the compressor off time between cycles. This is adjustable from 240 - 900 seconds. Min outdoor temp allows you to set the minimum outside air temperature at which the compressor will be disabled. This performs two functions: you can set it to prevent the c...
Page 14
Auxiliary heat stage 2 select this option when the thermostat is required to control a heat pump system with 2 stages of auxiliary heat. Connect the second stage of the auxiliary heat to this relay. Compressor/ac stage 2 select this option when the thermostat is required to control either a 2 stage ...
Page 15
Ac overcool max when using the ac to dehumidify, the section allows you to program how many degrees below the current set point the thermostat will run in order to reach the dehumidify set point. Aux heat settings max outdoor temperature allows you to set the maximum outdoor temperature threshold. A...
Page 16
Usage this section allows to configure what function this sensor needs to perform control sensor this option configures the sensor to be part of the hvac control. These sensor can then be configured to replace or be part of a the thermostat set temperature. Refer to page 27 in the user manual to con...
Page 17
Reset installation settings selecting this option will restore all the installation settings back to the factory default. Any user setting (not related to the equipment installed) will remain unchanged. Reset all setting selecting this option will reset the entire smart thermostat system back to the...
Page 18
Low temperature alert select this to set the temperature at which the smart thermostat will generate a low temperature alert. The range can be: off – no alert will be generated set temperature range of 35 – 68°f (1.5 – 20°c). High temperature alert select this to set the temperature at which the sma...
Page 19
3-year limited warranty ecobee warrants that for a period of three (3) years from the date of purchase by the consumer (“customer”), the ecobee smart thermostat (excluding battery) (the “product”) shall be free of defects in materials and workmanship under normal use and service. During the warranty...
Page 20
33 notes notes 34.