- DL manuals
- Ecoplus
- Water Heater
- SWBH 26
- Installation Instructions Manual
Ecoplus SWBH 26 Installation Instructions Manual
Summary of SWBH 26
Page 1
Installation & instruction manual high temp heat pump water heater.
Page 2
Ⅰ .To our customers(before installation) Ⅱ .Product introducing -----------------------------------------------------------------------2 Ⅲ .Work principle ------------------------------------------------------------------------------3 Ⅳ .Performance data ---------------------------------------------...
Page 3
Dear sir: Ⅰ. To our customers water heater in order to use this machine safely, please read this intruction manual carefully before using and installation. Heat pump water heater is a professional machine, it may cause damage or hazard when wrong installed, it should be installed by a competent pers...
Page 4
Product introducing safe and reliable unlike traditional electric water heater, heat pump water heater do not directly generate heat by electricity , it use less electricity to move heat from one place to another , electric circuit is separated from water circuit ,which is also not easy for electric...
Page 5
Work principle the low temperature and low pressure refrigerant gas come from the evaporate to the compressor, after the compressor compress it , the refrigerant gas became high temperature and high pressure. Then the gas come into the water condensation into liquid, emit a lot of condensation heat,...
Page 6
Performance data Ⅳ .Performance data water heater 4 measuring conditions: heating: dry bulb 20 ℃ , wet bulb 15 ℃ , water inlet 40 ℃ ,water outlet 45 ℃ . Swbh-26.0h-a-s model rated heating capacity(w) power supply(v/ph/hz) input power(kw) heat up water: heat up water: running current(a) thermostat fa...
Page 7
The dimension for high temp heat pump water heater Ⅴ .Dimension water heater 5 7 1 0 6 8 5 7 0 4 750 1450 1 2 6 0 1 6 0 1 6 5.
Page 8: Controller Introduction
Ⅵ .Operation introductions water heater controller introduction note: some button may not be suitable for all model, as the model update frequently,some operation may not be the same as instructed in this manual. Please refer to the controller operation instruction. Operation fig.1 1 2 on/off electr...
Page 9
Ⅵ .Operation introductions water heater fig.2 2. Button is to switch between operation mode and standby mode, operation mode as shown in fig.2. The temperature showed under " in " is the temperature of hot water in water tank. Fig.3 3. Button is to switch to electric heating mode, see fig.3: button ...
Page 10
Ⅵ .Operation introductions water heater 4.Clock setting: under standby mode or operation mode, press to enter clock setting, see fig.4. Blink, press or to adjust hour; press again, blink, press or to set minute. After setting, press again to confirm your settings. The screen will show your set clock...
Page 11
Ⅵ .Operation introductions water heater under standby mode, press or once, screen shows ( means screen display number( sn ), means the data of parameter). Press , blink, press or to set the data. Press once to confirm. Then press or to select another parameter. Under operation mode, press or once, s...
Page 12
7.Malfunction display / system protection if screen show ee 3 as fig.7,means malfunction for water flow switch, malfunction code see below: protection/malfunction water inlet temp sensor failure water outlet temp sensor failure system 1 coil temp sensor failure system 2 coil temp sensor failure syst...
Page 13
Bc series water pipe system drawing hot water outlet tap water inlet water water pressure switch circle typewater heater water pipe system drawing high-efficient heat exchanger Ⅶ .Appendix 11 8 setting about s1 & s2 switch s1 switch---second set point s2 switch----long distance demand 8.1 second set...
Page 14: H T
Wire circuit diagram Ⅷ .Wire circuit diagram water heater 12 n t r s 3 8 0 v / 5 0 h z c m 1 c m 2 w at er p um p c o m p re s s o r compressor 4-way valve transformer u u co nt ac to r co nt ac to r v v w w y lw /g r n y lw /g r n out1 out2 out3 out4 out7 out5 out8 out6 out9 5 5 ele ctr on ic e xp ...
Page 15
Installation instructions 1. Unit installation 1).Installation location host unit ²should be installed in a larger & well-ventilated place. ²installation location should ensure unhindered access outlet (inlet & outlet shown as below). ²install gutter or set up positions near the outfall, to facilita...
Page 16: Tank
Installation instructions 2. Pipeline connecting installation notes: ² water drain pipes, overflow pipes should be installed next to the drainage inlets to facilitate drainage, vent valve should be installed on vent pipes. ² repair valve should be installed in front of the electromagnetic valve on t...
Page 17: Warning!
Running test and operation 1. Preparatory work before the running test. A) inspection of heat pump water heater units: 1 check if the unit appearance and the pipeline system were damaged during transport. 1 check if there is air exist in the water pipes, if yes, should empty all the air inside by th...
Page 18
Running test and operation 2.Running test this running test must be performed by professional staff! 1 overall test can be run if the entire system inspection is conformed to regulations. 1 connected to power, start the heat pump, host unit delays three minutes then auto-start. For three-phase power...
Page 19
Maintenance heat pump water heater is a high automatic equipment, please perform regular inspection termly. If the unit can be long-term and efficiently maintenance, the operating reliability and service life will have an unexpected increase. 1.The extra water filters should be cleaned regularly to ...
Page 20
High temp heat pump-water heater.