1. DL manuals
  2. ECOVACS
  3. Vacuum Cleaner
  4. Deebot D56
  5. User Manual

ECOVACS Deebot D56 User Manual

Other manuals for Deebot D56: User Manual
Manual is about: Robot Vacuum Cleaner

Summary of Deebot D56

  • Page 1

    D56 user guide robot vacuum cleaner.

  • Page 3

    Thanks for purchasing products hope you can enjoy it thanks again for your choice! Patented . ! Robot vacuum cleaner.

  • Page 4

    1. Safety instruction....................... .. User guide............................ .... ... 10. Maintenance.................... ............. Power supply for the product......... ..... The spectrum of product use....... ....... Dust box cleaning notes before cleaning.................. ..... Cot...

  • Page 5

    1.Safety instruction 3 the user guide please conform to the basic safety precautions as follows: ● read the content in this user guide carefully and install the robot according to the detailed instructions. ● safekeeping this guide. If you transfer this machine to another person, please make sure at...

  • Page 6

    4 the spectrum of the product use ● the robot is applicable to domestic sweeping, including wooden floor, rubber floor, ceramic tile, linoleum and medium or shorthaired carpet. However, it is inapplicable to longhaired carpet. ● it can not be used for the floor as below: ---- have water on the surfa...

  • Page 7

    5 notes before cleaning ● take extra care of the robot when the first it works. Please remove the obstacles when it is beyond the robot. ● make precautions to solve the problem which may make the cleaning in trouble, such as: keep the easily knock over objects in a safe place. ---- permian the edge ...

  • Page 8

    6 ● take good care of the product and keep it beyond children and people who cannot judge danger nearby. Extra attention should be paid when the robot starts working. ● you should get the people inside the room know that the machine is working to avoid man-made damage like damaging. ● do not take ro...

  • Page 9

    D56 user guide robot vacuum cleaner roll brush clean-up gadget dc14.4v ac220-240v dc17.5v 50hz 30w 0.7a 30w 0.25m/s 0.7l ≤62db about 4~5 hours 60 minutes 120-150 2 m 335 × 335 × 100mm 2.8kg the host the charging block working voltage in-put voltage rated out-put voltage rated frequency rated power r...

  • Page 10

    3.Name of parts 8 control button wind gate rotating side brush up-ground height sensor all-round wheel suspended driving wheel rubber scraper on/off switch dust sensor dust sensor dust box dust box handle ash exit antibacterial sponge filter lock of dust box charging and alarm open button of upper c...

  • Page 11

    Mode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 20 19 21 22 1. Power 7. Border cleaning mode 13. One-time timing cleaning 19. Tip for cleaning dust box 2. Model selection 8. Intensive cleaning mode 14. Time display 20. Tip for lacking dust box 3. On/pause 9. Automatic cleaning mode 15. Time cleani...

  • Page 12

    Tangle the power cord and do not scatter it besides the block in case that robot would get impeded when it turns back. 1.5 m 0. 5 m 0. 5 m there should not be any object at least 1.5 meter in front of the charging block. Besides, anything with strong reflector is not supposed to stay ahead of the in...

  • Page 13

    ● get power supply and press the button on host. There would be a short music tip and at the same time the battery indicator lights. Press button to start the robot ● 5.Power on/ pause/ power off ● press key, it can pause the operation of robot and keep it stay where it is. ● press key, power is off...

  • Page 14

    10 put the robot on the charging block and keep it charging after finishing house cleaning. Do not keep the robot on pause status for long time, because the full charged battery could only last for around 20 hours. We suggest you to turn it off when you do not want it to work. Tips : press btuuon, t...

  • Page 15

    Route description: (like wall), it will run along it to clean until it meets obstacle and change the former route. Under this mode, once the robot detects hard objects under this mode, robot helps to clean the corner of wall, table, sofa and bed where it is beyond the mode of automatic cleaning. The...

  • Page 16

    7 .Automatically charging ？ ?? ● when robot detects the low battery, it will go back charging automatically. ● to make it easy for robot to search for charging block, you need to put the block back to the wall and make sure there is no obstacle within 1.5 meters ahead of the infrared receiver. Check...

  • Page 17

    Note: set cur rent time selection scope: hour is between 0 and 23, minute is between 0-59. Under normal circumstance, time display on lcd shows current time. Tips : 1. After appointment time setting, the label high light, and the number with time setting is flashing. 2. Set hour and minute via and ,...

  • Page 18

    1 1 9.Day-to-day storage 10.Maintenance you should keep robot stay at charger even though it finishes charging, because it will change to small currency to supplement charging. Charge the robot until full battery and put it back to the package if you do not need to use it for ling time. Keep the pac...

  • Page 19

    Tips ： if the dust box is not placed back or not properly placed, the indicator lights. 1 2 1 3 1 4 1 5 1 6 1 7 hold the handle of dust box and lift it to take out. In order to avoid dust leaking, lift the suction up when you take out dust box. Please mind your speed doing this step. Match the botto...

  • Page 20

    1 1 3 4 4 4 5 1 2 8 1 9 1 2 6 7 2 main brush cleaning tips: clean the main brush after it has operated for 4 or 5 recycles. Undo the screw fixed on the main brush. Remove the hair and dust which is in-between the belt. Put the main brush back to the host and take care of the anastomosis of belt. Fix...

  • Page 21

    Note： note: side brush cleaning replace sidebrush driving wheel cleaning up-ground height sensor cleaning please replace the side brush when it is destroyed. Please remove the screws, and take out the side brush. Please push the new side brush into the correct position. Tight the screws. Side brush ...

  • Page 22

    1 .Alarm function 1 dust sensor cleaning the dust sensor is located at the front of dust entrance. It is able to detect the concentration of dust so that it can choose efficient mode to work. We suggest you to clean dust sensor once you clean dust box to improve work efficiency. 1. Turn off power. 2...

  • Page 23

    4 3 2 1 12.Common failure no. Problem solution robot keeps proceeding or moving backward once power is on. Turn off the power. 1.Check if there is dust on up-ground height sensor, which cause robot to make wrong signal. Use half dry cloth to clean it. 2.Buffer collision is out of control. Put your h...

  • Page 24

    5 13.Other problems there is much noise when the robot works. 1. Check whether the suction of main brush is blocked. 2. Examine and clean the main brush. 3. Examine and clean the side brush. Turn off the power supply, and then take out of dust box. After removing the garbage, overturn the robot. If ...

  • Page 25

    9 why does robot fail to start cleaning on avoid wrong operation by child. Appointment time? 16 is there any danger to wrongly touch the answer: a.Confirm whether there is much docking electrode film between the host remaining battery. Appointment timing is not and charger? Applicable when robot is ...

  • Page 26

    21 what should do if robot sucked liquid? Answer: a. Turn off the power and take out dust box, then empty it and wipe it dry. B. Draw out the sponge filter and wipe it dry. C. Take out main brush and clean it, then use day cloth to wipe the brush and its interior. Wait until the brush is day and pla...

  • Page 28

    Enjoy smar ter life! D56-000im201 01 1.