1. DL manuals
  2. Edco
  3. Floor Machine
  4. DDG-9-I-0315
  5. Operator's Instruction Manual

Edco DDG-9-I-0315 Operator's Instruction Manual

Manual is about: NEW SINGLE-DISC FLOOR GRINDER

Summary of DDG-9-I-0315

  • Page 1

    Ddg-9-i-0315 operator’s instruction manual new single-disc floor grinder electric ddg-9 - direct drive grinder equipment development company equipment development company 100 thomas johnson drive, frederick, md 21702-4600 usa phone: 301-638-3326 • 301-663-1600 fax: 800-447-3326 • 301-663-1607 edcoin...

  • Page 2

    Eddg-9-i-0315 2 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company read and understand the operators instruction manual thoroughly before attempting to operate this equipment. Death or serious injury could occur if this machine is used improperly. Extreme care must be taken...

  • Page 3

    Ddg-9-i-0315 3 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company smi dust and silica warning grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or ill- nes...

  • Page 4: Table of Contents

    Ddg-9-i-0315 4 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company table of contents safety and warnings...................................................................................................................2-3 table of contents......................................

  • Page 5

    Ddg-9-i-0315 5 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company specifications note: all dimensions and weights are for reference only and subject to change at any time. Figure 1 how to order repair parts to insure product safety and reliability, always use genuine edco r...

  • Page 6

    Ddg-9-i-0315 6 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company operating controls please note: controls shown are for the model indicated. The location of these controls may vary on the different models. Due to improvements and changes in the equipment, the illustrations...

  • Page 7

    Ddg-9-i-0315 7 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company getting started with your new grinder this unit is intended for grinding horizonal, dry floors such as concrete, asphalt or steel surfaces. Note: the above illustrations are viewing the machine from the front...

  • Page 8

    Ddg-9-i-0315 8 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company getting started with your new grinder loading tools: return level lock to the operator position. Loading tools: lean back slightly on the handle to get the tools off the surface and start the machine. Lower t...

  • Page 9

    Ddg-9-i-0315 9 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company getting started with your new grinder leveling: you are looking for a complete circle. Leveling: if you see a partial circle repeat the process until complete circle is achieved..

  • Page 10

    Ddg-9-i-0315 10 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company operating instructions • read and understand all operating instructions before operating this equipment. Death or serious injury can result if this machine is used improperly. • concrete grinders are designe...

  • Page 11

    Ddg-9-i-0315 11 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company operating instructions • before starting the motor: raise the front of the machine clear of the working surface. • starting machine: depress and hold center button and squeeze either handle grip switch. Hold...

  • Page 12

    Ddg-9-i-0315 12 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company attaching a vacuum / servicing head assembly procedure for attaching a vacuum: when using a vacuum for dust control attach it to the vacuum port at the rear of the ma- chine as pictured above, securing it wi...

  • Page 13

    Ddg-9-i-0315 13 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company for use with dyma-slider system double diamond dots: general purpose grind - removes general purpose epoxy, mastics, thinsets, water-proofing coatings and more. Single diamond dots: aggressive grind - grinds...

  • Page 14

    Ddg-9-i-0315 14 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company maintenance instructions 1. Disconnect the machine from the power source. Disconnect the supply voltage con- nector at the machine on electric models before performing any maintenance. All main- tenance to b...

  • Page 15

    Ddg-9-i-0315 15 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company maintenance schedule before operation every 4 hours daily every 50 hours of op- eration as required visual inspection of entire machine x inspect grinding disc x clean dust & dirt off machine x read and foll...

  • Page 16: Notes:

    Ddg-9-i-0315 16 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company notes: _____________________________________________________ _____________________________________________________ _____________________________________________________ ______________________________________...

  • Page 17: Notes:

    Ddg-9-i-0315 17 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company notes: _____________________________________________________ _____________________________________________________ _____________________________________________________ ______________________________________...

  • Page 18: Notes:

    Ddg-9-i-0315 18 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company notes: _____________________________________________________ _____________________________________________________ _____________________________________________________ ______________________________________...

  • Page 19

    Ddg-9-i-0315 19 301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - equipment development company, inc. Herein referred to as edco (seller) warrants that each new unit manufactured ...

  • Page 20

    301-638-3326 • edcoinc.Com • sales@edcoinc.Com equipment development company surface preparation, restoration, professional sawing equipment & hand held tools 100 thomas johnson drive, frederick, md 21702 phone: 1-800-638-3326 or 301-663-1600 fax: 1-800-447-3326 or 301-663-1607 email: sales@edcoinc....