Eden Never Compromise WT405 Operation Manual - page 10
11
If you have disengaged the Compressor as we suggested, the Clip light will
barely blink on your loudest notes when you reach clipping in the Input
stage. We recommend you decrease gain one or two clicks to ensure there is
no clipping in the system. By the way, this is David’s favorite way to set
level, even if you intend to use compression.
Once you have properly set your Input Gain, turn the Master Volume up to a
comfortable listening level and proceed with the rest of the setup process.
Setting the Compressor - If you want to use compression, engage it now by
turning up the Compressor Threshold control. The compressor light will
blink when your gain goes above the compression threshold. This will
generally show up more on the lower notes, or when you employ Slapping.
(A properly compressed Slap sound is very cool, indeed.)
SETTING YOUR EQ
The frequencies that you’ll need to boost or cut are dependent upon your
instrument, playing style, speaker cabinets, and venue. Extreme settings of
boost or cut are unlikely to be necessary or helpful. We are frequently asked
to provide suggested settings for various styles of play. We have discovered
though, that most of our endorsers tend to set their EQ generally flat, using
varying amounts of the Enhance Control to achieve their sound. In fact, a
number of our recording artists tell us that their standard recording set-up is
to have the Enhance set at approximately 9 or 10 O’clock and the tone
controls set flat. They then send a post-EQ D.I. to the board.
We encourage you to experiment with different settings to obtain the sound
you desire. We have included some EQ panel diagrams at the back of this
manual to help you record your settings.
Enhance – Once you’ve set your gain, you can move on to setting your EQ,
beginning with the Enhance control, or Magic Knob, as some call it. The
Enhance circuitry adds very low bass, upper mids and highs while scooping
out a bit of low middle. The more Enhance effect you dial in, the greater the
boost (and cut). As with all of our EQ controls, a little goes a long way.
Slowly bring the Enhance control up while playing. If you turn it up close to
maximum on the dial and still don’t have your sound, stop there. Return the
Enhance to OFF or leave it at no more than 12:00 and work with the EQ
section.
10
INITIAL SET UP
As bassists, each of us has in our head a concept of our perfect sound. Eden
amplifiers are designed to help you easily achieve the sound you hear inside
you. However, it’s a multi-step process as explained below.
In order to ensure the ultimate in tone, it’s important to follow the procedure
outlined below. Don’t skip steps; don’t jump around. Yes, this may take a
minute or two, but the work is well worth it. Once they’ve done it a few
times, most users can do it time and again in about a minute.
IMPORTANT NOTE: Before you plug in your unit for the first time,
please do the following things. First, turn the power switch to the OFF
position. Check the back of your unit for the correct voltage notation for
your county of operation.
Once you’ve ensured correct voltage, set the Master Volume control to
minimum (fully counter-clockwise). Set the tone controls to the center
position (12:00 or 0). Turn the Enhance control to the minimum position. Set
the Input Gain control to the minimum (fully counter-clockwise). Set the
Compressor to the OFF position (fully counter-clockwise). On the front of
the unit, set the Speaker switch in the ON position. Make sure the Dynamic
Boost switches are OFF. This will set your amplifier up flat and with the
Compressor disengaged. Next, plug in the power cord to the AC inlet on the
back of the unit. Use only a safe grounded receptacle for proper operation at
the correct voltage for your country. Double check to make certain your
amplifier is set for the correct voltage in your country.
Turn On – Once you’ve completed the steps above, you can plug in your
bass and turn on the unit (plug it in first, ok?) and let’s get started. We
recommend turning your system on with the Master Volume control set to
its minimum position. This will prevent any unexpected signal from being
sent to your speakers.
Setting Your Level – Remember, begin with the Input Gain, Enhance,
Compressor and Master Volume completely OFF – fully counter-clockwise.
All EQ should be set flat, that is, at 12:00 – straight up.
While playing your lowest note (or loudest), slowly turn the Input Gain up
until the Clip light begins to blink with regularity. If you go past 2 or 3
o’clock, engage the Gain Switch to better match the gain of your instrument
to the amplifier.