Faber Pro Magnum User Instructions - Warning

Version 04/08 - Page 4

TOOLS  NEEDED  FOR  INSTALLATION

• Saber Saw or Jig Saw

• Drill

• 1  1/4" Wood Drill Bit

• Pliers

• Phillips Screwdriver

• Flat Blade Screwdriver

• Wire Stripper or Utility Knife

• Metal Snips

• Measuring Tape or Ruler

• Level

• Pencil

• Caulking Gun

• Duct Tape

PARTS  SUPPLIED  FOR  INSTALLATION

• 1 Hardware Package

• 1 Literature Package

PARTS  NEEDED  FOR  INSTALLATION

• 2 Conduit Connectors

• Power Supply Cable

• 1 Wall or Roof Cap

• All Metal Ductwork

OPTIONAL ACCESSORIES AVAILABLE

• 30" High Backsplash

30" high, mounts to the wall beneath the rangehood 

for a coordinated look

part # 620000095 - 30" model

part # 620000097 - 36" model

part # 620000098 - 48" model

• Telescopic Chimney Kit (FIGURE 3)

24" wide, extends to accomodate 8 - 9 foot ceilings

part # 6097336 fits all size hoods

• Full Width Duct Cover (FIGURE 4)

12" high, extends full width of the hood

part # 6097337 - 30" model

part # 6097338 - 36" model

part # 6097339 - 48" model

• Duct Transition Kit

For 48" model only, optional kit transitions two 3 1/4" 

x 10" openings to one 10" round opening

part # 6000002

• *Charcoal Filters

* it is highly recommended that professional style 

cooking always be vented to the outside; for reciru-

lating installations, some ductwork is required to 

exhaust the unit out of the cabinet. For 48" model, 

order 2 kits, one for each motor.

part # 6093034

RANGEHOOD  WITH 

TELESCOPIC CHIMNEY KIT

CALCULATE  THE  DUCTRUN  LENGTH

   WARNING

Due to the weight and size of the rangehood 

canopy, two or more people are needed to move 

and safely install the rangehood canopy.

Failure to properly lift rangehood could result in 

damage to the product or personal injury.

PERSONAL INJURY HAZARD

9 Feet Straight Duct

2 - 90˚ Elbows

Wall Cap

Total System

9.0 feet

10.0 feet

0.0 feet

19.0 feet

FIGURE  2

3.0 feet

5.0 feet

12.0 feet

0.0 feet

45˚ Elbow

90˚ Elbow

90˚ Flat Elbow

Wall Cap

FIGURE 1

PLAN  THE  INSTALLATION

This rangehood can be vented through the wall or ceiling.  To vent through a wall, 

the blower must be turned to vent to the rear.  This rangehood can be installed 

with two different chimney options as well as without a chimney.  Before you begin 

installation, you must determine which chimney installation will be used.

The Telescopic Chimney Kit is adjustable and designed to meet varying ceiling 

heights from 8 to 9 feet.  FIGURE 3 illustrates the dimensions of the rangehood 

with the optional Telescopic Chimney Kit.  FIGURE 4 illustrates the dimensions 

of the rangehood with the optional Full Width Duct Cover.  The body of the 

rangehood is the same dimensions regardless of the chimney option used.

WARNING!  BEFORE MAKING ANY CUTS OR HOLES FOR INSTALLATION, 

DETERMINE WHICH VENTING METHOD AND CHIMNEY WILL BE USED AND 

CAREFULLY CALCULATE ALL MEASUREMENTS.

25

"

25

"

25

"

25

"

RANGEHOOD WITH  

FULL WIDTH  DUCT  COVER

FIGURE  3

FIGURE  4

The ductrun should not exceed 35 equivalent 

feet if ducted with the required minimum of 3 

1/4" by 10" rectangular duct or 55 equivalent 

feet  if  ducted  with  10"  round  duct  (when 

using  Duct  Transition  Kit  for  48”  model 

only).   Calculate the length of the ductwork 

by adding the equivalent feet in FIGURE 1 for 

each piece of duct in the system  An example 

is given in FIGURE 2.  For best results, use 

no more than three 90° elbows. Make sure 

that there is a minimum of 24" of straight 

duct between elbows if more than one is 

used. Do not install two elbows together. 

If you must elbow right away, do it as far 

away from the hood's exhaust opening 

as possible.

!