Fadini Junior 633 Instruction Manual - Elpro 63
page 20
GB
General description: The Elpro 63 is a PCB card with microprocessor for the command and management of the Junior 633 and Junior 650 sliding gate
opener with programming for self-learning of the different movement phases of the gate.
Power Supply: 230V 50Hz±10% monophase corresponding to the 2006/95/CE Low Voltage directive and the 2004/108/CE & 92/31/CEE Electro-magnetic
Compatibility Directive.
Logic Operation: given the open command impulse, it performs the function for open, pause, close in automatic or semi-automatic with programmable
slowdown, possibility of step by step radio command, radio no reverse on opening, with or without pre-flashing, reverse run upon contact with an
obstacle and LED diagnostics. Rh and Lh installations are made selectable by Dip-switch, Blue/Amber LED diffuser on the cover casing for the gate
opener status signal.
DIAGNOSTIC LED: LED status during proper operation of the system, the green LEDs must always be on; the red LEDs must always be off.
L2 (green on) = Photocells, turns off with obstacle present
L4 (red off) = Open, lights up with the opening command impulse
L5 (red off) = Close, lights up with the closing command impulse
L6 (green on) = Stop, goes off with the stop command impulse
L7 (red off) = Radio, lights up with each transmitter impulse
L10 (red off) = Lights up in case of short circuit with 24 Vdc. Goes off when circuit problem is corrected
L20 (red off) = Pedestrian, lights up with the open command for pedestrians
L21 (green on) = Photocell in open, turns off in case of ostacle
L22 (green on) = 2
nd
Junior input
LP (red off) = Program led, it lights on in phase of programming
X (red) = led limit switch, always alight during the movement
Y (red) = led limit switch, always alight during the movement
DIP-SWITCH enables the performance of all of the possible functions of the Junior 633 and Junior 650 sliding gate opener
1 = OFF: Photocell does not stop gate in opening
2 = OFF: Radio stops and reverses in opening
3 = OFF: Semiautomatic operation
4 = OFF: Without pre-flashing before opening
5 = OFF: Radio reverses direction on every impulse
6 = OFF: Slowdowns (to be programmed)
7 = OFF: Activates “Reverse”: running is reversed upon contact
8 = OFF: Flasher on in pause
9 = OFF: No closing after passage by the photocell
10 = OFF: No DSA control on the photocells
11 = OFF: Junior 633/Junior 650 installed on the Left
12 = OFF: Single Elpro 63, or 1
st
Junior 633/Junior 650 as MASTER
1 = ON: Photocell stops gate in opening
2 = ON: Radio does not reverse (and does not stop) in openig
3 = ON: Close in automatic after pause time
4 = ON: Pre-flashing before opening
5 = ON: Radio switch: open-stop-close-stop
6 = ON: No slowdowns
7 = ON: No direction reversing upon contact
8 = ON: Flasher off in pause
9 = ON: Closing after passage by the photocell
10 = ON: DSA Photocell control before start up
11 = ON: Junior 633/Junior 650 installed on the Right
12 = ON: Elpro 63 SLAVE, 2
nd
Junior 633/Junior 650
LED on
LED off
LED X on
LED Y off
LED X off
LED Y on
Fully Open
Fully Open
Junior Sx
Junior Sx
Junior Dx
Junior Dx
ATTENTION !! The installation of this product must be performed by professionally trained and qualified personnel according to the safety regulations in
force. It is important to carefully read and follow the instructions so as to avoid incorrect use of this same product. The ELPRO 63 electronic programmer
was conceived and manufactured for the managements of the Junior 633 and Junior 650 electromechanical sliding operators with 230V motors. Any other
use different from that specified in this instruction booklet is to be considered prohibited.
ATTENTION !! The Meccanica Fadini Company declines any responsibility for damages caused to properties and/or people due to any improper instal-
lation or the lack of bringing the system to compliance whit the laws and regulations in force. The application of the Machine Directive 2006/42/CE is
required. All of the maintenance and/or test operations of the status of the product must be performed by professionally trained and qualified personnel.
ATTENTION !! Important: before carrying out any procedure on the PCB card, disconnect the electrical power supply mains.
It is furthermore recommended that the “Safety Regulations” made available by Meccanica Fadini be examined throughly.