1. DL manuals
  2. Falcon
  3. Oven
  4. G2102
  5. Installation And Servicing Instructions

Falcon G2102 Installation And Servicing Instructions

Manual is about: FORCED CONVECTION OVEN

Summary of G2102

  • Page 1

    G2102 forced convection oven range g2112 forced convection oven (may 2010) installation and servicing instructions these appliances must be installed and serviced by a competent person as stipulated by the gas safety (installation & use) regulations. Important the installer must ensure that the inst...

  • Page 2: Warranty Policy Shortlist

    Warranty policy shortlist warranty does not cover :- correcting faults caused by incorrect installation of a product. Where an engineer cannot gain access to a site or a product. Repeat commission visits. Replacement of any parts where damage has been caused by misuse. Engineer waiting time will be ...

  • Page 3

    Section 1 – installation unless otherwise stated, parts which have been protected by the manufacturer are not to be adjusted by the installer 1.1 model numbers, nett weights and dimensions model width mm depth mm height mm weight kg g2102 range 900 855 870 221 g2112 oven on stand 900 855 1310 190 g2...

  • Page 4

    There must be no direct connection of the flue to any mechanical extraction system or the outside air. Open top burners discharge combustion products directly into the room. Siting the appliance under a canopy is the ideal arrangement. 1.4 gas supply the incoming service must be of sufficient size t...

  • Page 5: 2. 1 Assembly

    1.9 gas pressure supply pressure burner operating pressure oven ignition pressure nat prop nat prop nat prop mbar 20 37 15 37 5 12 1.10 burner adjustments 1.10.1 burner aeration all burners have fixed aeration, and no modifications to the size of air-entry should be attempted. 1.10.2 open top - bypa...

  • Page 6

    5. Manoeuvre oven and stand into desired location and level by turning lower part of the feet. 6. Connect to gas and electrical supplies as detailed in sections 1.4 and 1.5. Figure 1. 2.1.4. G2112/2 two tier oven (see figure 2) these units are marked as top and bottom ovens before leaving the factor...

  • Page 7

    Figure 2. 2.1.5 assembly of splashplate and plate shelf (see figure 3) a) fix as per instructions supplied with kit. 2.2 connection to a gas supply the gas supply piping and connection to unit must be installed in accordance with the various regulations listed on front page of this document. Refer f...

  • Page 8

    B) oven burner is controlled by a two stage multifunctional control. Pressure should pause for a brief period at an intermediate level (oven ignition pressure) before attaining burner operating pressure. Refer to section 1.9 for these settings. If adjustment is necessary, refer to sections 2.5.4 to ...

  • Page 9

    Thermocouple connection pilot connection (behind) (behind) inlet pressure test point main burner button pilot adjustment 1 st step adjustment off button reg adjustment pilot button outlet pressure test point no pr figure 3. 2.5.5 mfc set-up procedure (natural gas) 1. Remove screw from outlet test po...

  • Page 10

    8. Continue to hold pilot button in fully for 20 seconds before release. The pilot should remain alight. If it goes out, push off button in and wait for the 3 minute lockout to release before repeating from step 7. 9. Push main burner button down. 10. Switch main electrical supply to unit on and che...

  • Page 11

    Remove hob pan supports and burner head complete with aluminium bezel and venturi. The latter fits loosely upon burner retaining ring. The hob is retained by four ball-stud fixings. Pull hob upward to access burner supports. Replace parts in reverse order. Ensure burner head locates correctly upon b...

  • Page 12

    3.4.2 open top thermocouple (g2102 only) remove hob as detailed in section 3.2.3. Remove nut securing thermocouple to burner support bracket and pull thermocouple through support bracket from underside. Undo thermocouple connection at ffd section of gas tap and carefully remove thermocouple from hob...

  • Page 13

    Remove pan support, burner head and aluminium bezel. Place extended socket down main burner body centre. Undo and carefully remove injector. Replace in reverse order. 3.9 open top pressure governor (g2102 only) the type of governor used is maintenance free. Check that blue dust cap for the vent is f...

  • Page 14

    3.15 neons open oven control panel as detailed in section 3.2.1. Disconnect wiring and push neon out of location. Replace in reverse order. 3.16 oven light push button open oven control panel as detailed in section 3.2.1. Remove push-on connectors at rear. Undo rear fixing nut and remove. Replace in...

  • Page 15: Section 4 – Spares

    Section 4 – spares when ordering any spare parts always quote the appliance type and serial number. This information will be found on the data plate attached to the side of the control compartment. A short list of spare parts is included in the user manual..

  • Page 16

    G2112/2102 wiring diagram.