- DL manuals
- Fanimation
- Fan
- Alamosa FP3820RP
- Owner's Manual
Fanimation Alamosa FP3820RP Owner's Manual
Summary of Alamosa FP3820RP
Page 1
Owner’s manual read and save these instructions model no. Fp3820rp the alamosa ® ceiling fan net weight 18.9 kg (42 lbs).
Page 2
1. Limited lifetime motor warranty - if any part of your fan motor fails, due to a defect in materials or workmanship during the lifetime of the original purchaser, fanimation will provide the replacement part free of charge, when the defective fan is returned to our national service center. Proof o...
Page 3
This manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will be...
Page 4
4 electrical and structural requirements your new ceiling fan will require a grounded electrical supply line of 120 volts ac, 60 hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Figure 1 depicts different structural configurations th...
Page 5
5 how to assemble your ceiling fan pin setscrew hanger ball figure 1 1. Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod. (figure 1) remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinst...
Page 6
6 how to assemble your ceiling fan (cont’d) 6. While pulling up on the hanger ball, securely tighten the two 3/16-24 x 3/8˝ setscrews in the downrod support. (figure 3) 7. The fan comes with blue, black, and white leads. Before installing fan, measure up approximately 6-9 inches above top of downrod...
Page 7
Ceiling joist wood member (2˝ x 4˝ approx.) how to hang your ceiling fan figure 1 floor ceiling no less than 7 ft 7 ▲warning the fan must be hung with at least 7´ of clearance from floor to blades (figure 1) ▲warning the outlet box must be securely anchored and capable of withstanding a load of at l...
Page 8
8 how to wire your ceiling fan - pull chain if you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. 1. Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the suppl...
Page 9
9 assembling and mounting the fan blades, & adapter/switch hsg note: shipping support plate must be removed prior to assembling blades! Blade & blade holder assembly: 1. Lay the side of the blade holder on a flat surface with the inside of the blade holder facing up. This is the side with the thread...
Page 10
10 maintenance periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the fi nish. Abrasive cleaning agents are not required and should be avoided to prevent damage to fi nish. Caution do not use w...
Page 11
11 trouble shooting blade cleaning periodic light dusting of the wood blades is recommended. A feather duster will work best. Avoid using water, cleansers, or harsh rags, which can warp and ruin the blades. ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble sho...
Page 12
12 before discarding packaging materials, be certain all parts have been removed parts list model #fp3820rp ref. # description part # 1 hanger bracket assembly apg510bl 2 downrod/hanger ball assembly containing: adr6bl 2a hanger ball assembly 2b downrod 2c hairpin clip 2d clevis pin 3 ceiling canopy...
Page 13
7 6 5 the alamosa ® fp3820rp exploded-view 4 1 3 2a 2b 2c 2d 2 note: the illustration shown is not to scale or its actual confi guration may vary figure 1 8 9 10 11a 11 4a 13.
Page 14
10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website @ www.Fanimation.Com copyright 2007 fanimation 2007/01.