Owner’s manual read and save these instructions model no. Fp10 / 20 fan series model no. Fp1280 motor series the brewmaster ® belt-driven ceiling fans suitable for use with solid state speed controls warning: support directly from building structure long neck fp20 net weight 15 lbs (6.8 kg) short ne...
Table of contents (motor assembly) unpacking instructions and parts identifi cation . . . . . . . . . . . . . . . . . . . . .3 (pulley assembly) unpacking instructions and parts identifi cation . . . . . . . . . . . . . . . . . . . .4 electrical and structural requirements . . . . . . . . . . . . . ...
3 this manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions and parts identifi cation for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps hav...
4 unpacking instructions and parts identifi cation (cont’d) lag bolts (4) & flat washers (4) wood blade holders (for use with fp1022, fp1026, fp1030 blade sets) traditional blade holders (for use with palm, bamboo, wicker blade sets) note: the illustration shown is not to scale or its actual confi g...
5 electrical and structural requirements lighting options optional lighting fi tters and light kits are available, including a single bowl fi xture with a maximum of 180 watts and a variety of four light fi xtures with a maximum of 240 watts. Can be only mounted on the motor switch cup. Installation...
6 how to set your switch cap remote receiver this step is to be completed prior to hanging your motor. 1. Removing the switch housing: remove the switch housing from the motor by unscrewing the three screws and unplugging the connector (figures 1 & 2). 2. Removing the receiver unit: carefully, slide...
7 how to set and operate your c20 remote control must operate in conjunction with switch cap control receiver figure 6 figure 5 9v battery remote transmitter unit detail receiver unit detail c20 remote be sure the electricity to the fan motor is turned off! 1. Setting the code: the remote unit has 1...
8 how to hang and wire your ceiling fan 1. You will first drill ³⁄ 16 ˝ pilot holes into the plywood base or supporting member to prevent splitting or cracking. Mount the pulley assembly on the ceiling with 4 lag bolts and flat washers (figure 1a). 2. Drill ³⁄ 16 ˝ pilot hole located approximately a...
9 how to hang and wire your ceiling fan (cont’d) 4. Connect the green grounding lead from the fan motor to the supply grounding conductor (this may be a bare wire or wire with green colored insulation). Securely connect wires with wire connectors supplied. (figure 3) 5. Mount retainer to junction bo...
10 belt splicing instructions 1. Wrap the belting around the two pulleys that will be connected and overlap the belting as shown. Use the spring clamps provided to hold the belting in place temporarily. With the clamps remaining in the same place, grasp both ends of the belting and pull tight. The c...
11 maintenance figure 2 mounting the fan blades natural palm leaf, woven bamboo, woven wicker blades 1. Lay side “a” of the blade holder on a fl at surface with the inside of the blade holder facing up. This is the side with the threaded posts and pitched foot (figure 1). 2. Position the palm leaf, ...
12 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connection...
13 18 exploded-view the brewmaster ® motor pack fp1280 note: the illustration shown is not to scale or its actual confi guration may vary. Wires partially removed for clarity. 19 15 20 1 2 3 4 7 5 6 10 9 11 13 14 12 ref. # description part # brewmaster motor assembly fma1280 ¾ 1 switch cap assembly ...
14 ref. # description part # pulley assembly fp10¾/fp20¾ 1 pulley with set screw ' 2a short frame (short model) ' 2b long frame (long model) ' 3 cushion, bearing, black ' 4 bearing ' 5 shaft ' 6 hub ' 7 blade holder (2) (wooden blades only) p1212¾ 8 bag, bh to hub screws,10-32 x ½˝,black (5) hdwfp10...
Note: the illustration shown is not to scale or its actual confi guration may vary. Exploded-view 8 the brewmaster ® pulley assembly pack fp10__ (short) / fp20__ (long) 15 7 11 6 5 3 4 2a 2b 1 3 4 14 9 8 9 10 11 12 13 10 figure 2 15.
10983 bennett parkway zionsville, in 46077 toll free (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website www.Fanimation.Com copyright 2008 fanimation 2008/02.
