1. DL manuals
  2. Fanimation
  3. Fan
  4. CANCUN FP8042 SERIES
  5. Owner's Manual

Fanimation CANCUN FP8042 SERIES Owner's Manual

Summary of CANCUN FP8042 SERIES

  • Page 2: Limited Lifetime Warranty

    Limited lifetime motor warranty - if any part of your fan motor fails, due to a defect in materials or workmanship during 1. The lifetime of the original purchaser, fanimation will provide the replacement part free of charge, when the defective fan is returned to our national service center. Proof o...

  • Page 3: Unpacking Instructions

    3 this manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will ...

  • Page 4: Energ

    4 electrical and structural requirements your new ceiling fan will require a grounded electrical supply line of 120 volts ac, 60 hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 35 lbs. Figure 1 depicts different structural configurations th...

  • Page 5

    5 4. Route wires through motor coupling cover, canopy screw cover and ceiling canopy. (figure 4) how to assemble your ceiling fan 1. Remove the hanger ball portion from the downrod/ hanger ball assembly by loosening the set screw in the hanger ball until the ball falls freely down the downrod. Remov...

  • Page 6: How to Hang Your Ceiling Fan

    6 how to assemble your ceiling fan (continued) 6. Cut off excess lead wire approximately 6 to 9 inches above top of the top of the downrod. Strip insulation off 1/2 inch from the end of each lead wire. (figure 6) figure 6 how to hang your ceiling fan note: if you are not sure if the outlet box is gr...

  • Page 7: How to Wire Your Ceiling Fan

    7 how to wire your ceiling fan 1. Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the supply grounding conductor (this may be a bare wire or wire with green colored insulation). Securely connect wires with wire connectors supplied. (figur...

  • Page 8: How to Assemble The Blades

    8 installing the canopy housing (continued) 2. Securely attach and tighten the canopy screw cover over the shoulder screws in the hanger bracket utilizing the key slot twist-lock feature. (figure 15) figure 15 canopy screw cover how to assemble the blades 1. Remove and discard the five rubber motor ...

  • Page 9

    9 housing/switch cup adapter assembly 1. Disassemble the housing switch cup/adapter assembly by removing three screws. (figure 19) figure 19 housing/switch cup adapter 2. Remove one of the three screws in the support bracket. Slightly loosen the remaining two screws. Assemble the adapter assembly to...

  • Page 10

    10 light kit assembly—fp8011ob only 1. Install included candelabra bulbs into each of the three sockets. (figure 23) figure 23 . T u n d e il p p u s g n i s u r e tt fi t h g il o t l w o b s s a l g e r u c e s . 2 next, install trim cover followed by the finial. Do not over tighten. (figure 24) 3. ...

  • Page 11: Maintenance

    11 fp8009ob fp80011ob figure 28 3. If airflow is desired in the opposite direction, turn the fan off and wait for the blades to stop turning. Then slide the reverse switch to the opposite position and turn fan on again. Your fan model is equipped with a 4-position, 3-speed, pull chain switch. (figur...

  • Page 12: Parts List

    1 2 before discarding packaging materials, be certain all parts have been removed parts list models fp8009ob & fp8011ob ref. # description fp8009ob fp8011ob 1 hanger bracket assembly ap255bl ap255bl 2 downrod/hanger ball assembly: adr1-45ob adr1-45ob 3 ceiling canopy pg165ob pg165ob 4 canopy screw c...

  • Page 13: Fp8009Ob & Fp8011Ob

    1 3 fp8009ob & fp8011ob exploded-view note: the illustration shown is not to scale or its actual configuration may vary 1 2 3 4 5 6 7a 7b 11 11 11 11 11 10 fp8009ob only fp8011ob only 9 8.

  • Page 14: Trouble Shooting

    1 4 trouble shooting warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connection...

  • Page 16

    Copyright 2009 fanimation 2009/1 1 10983 bennett parkway zionsville, in 46077 toll free (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website @ www.Fanimation.Com.