- DL manuals
- Fanimation
- Fan
- Kubix FP4420 Series
- Owner's Manual
Fanimation Kubix FP4420 Series Owner's Manual
Summary of Kubix FP4420 Series
Page 1
Model no. Fp4420** the kubix ™ ceiling fan net weight 10.21 kg (22.5 lbs) owner’s manual read and save these instructions.
Page 2
1. Limited lifetime motor warranty - if any part of your fan motor fails, due to a defect in materials or workmanship during the lifetime of the original purchaser, fanimation will provide the replacement part free of charge, when the defective fan is returned to our national service center. Proof o...
Page 3
This manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will be...
Page 4
4 electrical and structural requirements your new ceiling fan will require a grounded electrical supply line of 120 volts ac, 60 hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Figure 1 depicts different structural configurations th...
Page 5
5 how to assemble your ceiling fan 1. Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod. (figure 1) remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstallation in step 4 (figure 4). 2. ...
Page 6
6 hanger bracket is loose and free to rotate this lag bolt is not fully fastened figure 1 fan alignment and hanger bracket installation 1. Preliminary hanger bracket attachment (figure 1): drill ¼˝ pilot hole through the center of the junction box, into the ceiling joist or structural member. Loosel...
Page 7
Figure 1 floor no less than 7 ft 7 ▲warning failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard. ▲warning to avoid possible shock, do not pinch wires between the downrod/hanger ball assembly and the hanger bracket. Final fan assembly 1. Make sure th...
Page 8
8 how to wire your ceiling fan - c24 remote control 1. Setting the code: the remote unit has 16 different code combinations. To prevent possible interference from or to other remote units such as garage door openers, car alarm or security systems, simply change the combination code in your transmitt...
Page 9
9 mounting the fan blades 1. Attach blades to the motor hub using the provided washer head screws and fiber washers.Make sure the screws securing the blades to the motor hub are tight and are properly seated. Do not overtighten. (figures 1 & 2) figure 2 fan blade washer-head screw with fi ber washer...
Page 10
10 installing the lower housing light kit assembly 3. Securely attach plugs from motor to sockets on downlight support plate assembly (figure 3) 4. Securely attach downlight support plate assembly to the lower housing assembly with four screws provided. (figure 4) figure 2 figure 4 figure 3 2. Secur...
Page 11
11 installing the lower housing light kit assembly (cont’d) figure 5 figure 6 figure 7 5. Install two candelabra bulbs (not included - 60 watts max) in each of the sockets on the downlight socket plate assembly. (figure 5) 7. Carefully install the glass/frame retainer spring clips into the retainer ...
Page 12
12 operating instructions - c24 remote control 1. Operating & using remote transmitter (figure 1): install 9 volt battery (if not using for long periods of time, remove battery to prevent damage to transmitter). Store the transmitter away from excess heat or humidity. Note: if airflow is desired in ...
Page 13
13 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connection...
Page 14
14 before discarding packaging materials, be certain all parts have been removed parts list model #fp4420** ref. # description part # 1 hanger bracket assembly (apg610bl) with shoulder screws (2) ahb442030 2 downrod/hanger ball assembly containing: adr1-6** 2a hanger ball assembly 2b downrod 2c hair...
Page 15
Note: the illustration shown is not to scale or its actual confi guration may vary the kubix ™ fp4420** exploded-view 4 1 figure 1 3 2a 8 10 7 5 6 12 13 14 11 2b 2c 2d 2 reversing switch 9 15.
Page 16
10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website www.Fanimation.Com copyright 2008 fanimation 2008/02.