1. DL manuals
  2. Fanvil
  3. Intercom System
  4. I20-T
  5. User Manual

Fanvil I20-T User Manual

Other manuals for I20-T: User Manual, Quick Installation Manual
Manual is about: Door phone

Summary of I20-T

  • Page 1

    I20-t door phone user manual.

  • Page 2: Safety Notices

    2 safety notices 1. Please use the specified power adapter. If special circumstances need to use the power adapter provided by other manufacturers,please make sure the voltage and current provided in accordance with the requirements of this product, meanwhile, please use the safety certificated prod...

  • Page 3: Table of Content

    3 table of content 1. Acquaint i20-t.................................................... 4 1.1. I20-t front ............................................................................................................................................................... 4 1.2. Key description ............

  • Page 4

    4 1. Acquaint i20-t voice intercom i20-t voice entrance guard is a full digital network door phone，its core part adopt fanvil mature voip solution（broadcom1190 chipset), stable and reliable performance, hands-free adopting digital full-duplex mode，voice loud and clear；generous appearance, solid dura...

  • Page 5

    5 1.2. Key description key chinese specification function digit keyboard enter the password to open the door or make a calling programmable keyboard can be set to a variety of functions，to meet the needs of different occasions call status indicators s tandby-light off ring-2 sec.Glitter hold/be hold...

  • Page 6

    6 connect network one end with i20-t wan port，connect the other end with your adsl modem lan port,then network hardware connection is completed. In most cases，if you are using the tv cable broadband，you must set your i20-t network as dhcp mode：if you are using adsl，then you must set your i20-t netwo...

  • Page 7

    7 2.1.2.2 electric lock connection driver option 【 notice】 when the initial electric current of the lock is less than 500ma/12v, you can access to the internal driven mode and use the poe of the voice access system or 12v dc to control the the switch of the electric lock ; when the initial electric ...

  • Page 8

    8 √ √ outside driver 1 2 3 4 √ √ inside driver 1 2 3 4 electric lock power supply mode electric lock jumper jp1 mode of connection internal externa l no nc √ √ outsid e driver 1 2 3 4.

  • Page 9

    9 √ √ outside driver 1 2 3 4 2.2. Quick setting i20-t provide a complete function and parameter setting,users may need to have the network and sip protocol knowledge for understanding the meaning represented by all parameters.In order to let i20-t users can quickly enjoy the high quality speech brou...

  • Page 10

    10 3. I20-t door phone basic operation 3.1. Answering a call when calling come，i20-t will ring，and configurate the shortcut as ok, then can press shortcut and answer the call. 3.2. Making a call speed dial configurate shortcut as memory key and setup a number, then press shortcut can call the config...

  • Page 11: Page Configuration

    11 3.5. Door open operation through the following four ways to open the door: 1. Input the local password on the keyboard to open the door. 2. The door phone call the owner，the owner enter the remote password to open the door. 3. Owner/other phone call the door，then enter the access code and remote ...

  • Page 12

    12 ）you can see the web management interface login screen（as below image）。enter the user name and password and click on the【logon】button then can enter into the set menu. ※ :if you do not save the settings you changed，next power boot it will back to the previous state unchanged. If you want to save ...

  • Page 13

    13 wizard field name description telephone network on-line mode, please according to the actual network environment ， select the appropriate network model.This phone provides three kinds of network online ways： static : if your isp services provide you with a fixed ip address，you can choose this.Aft...

  • Page 14

    14 ip address please enter your assigned ip addresses. Subnet mask please enter your assigned subnet mask. Ip gateway please enter your assigned a default gateway address. Dns domain set the dns domain suffix. When the user input in the dns domain name address and cannot be resolved， telephone will ...

  • Page 15

    15 show your manual configuration details. Select dhcp mode，click【next】c an simple sip parameter （ defaulted as 1 line） and browse configuration items. Click 【 back】 return to the last page ， specific operation same as static ip mode。 select pppoe mode，click【next】can simply configurate online accoun...

  • Page 16

    16 field name description start time the call log start time. Duration the call records of talk time. Dialed calls this call log is the account of other side and call protocol and using line. Type placed(answered),missed（missed）,received （ incoming). 4.3.2. Network 4.3.2.1. Wan config wan config fie...

  • Page 17

    17 telephone network on-line mode. Please according to the actual network environment ， choose a suitable network mode. This phone provides three ways for network online ： static ：if your isp services provide you with fixed ip address，then you can choose this item. After choosing, you must fill it i...

  • Page 18

    18 phone. 3）if system boot and use dhcp to get ip，and dhcp server network address are the same with system lan network address ， then after server get dhcp ip, add 1 to the last of lan network address，meanwhile modify lan dhcp server allocate ip address field；after system reboot，wan access dhcp log ...

  • Page 19

    19 forwarded to the port 2、3、4. In chart 2，the switch generate red and blue vlan；meanwhile set port 1、2 as red vlan、port 3、 4 are vlan. Then a（port 1）send out broadcast frame，switches only will forward it to other port belongs to a vlan——port 2 which also belong to red vlan，will not be forwarded to ...

  • Page 20

    20 wan port vlan id configurate id value of vlan，range is 0-4095 signal 802.1p priority configurate the value of signal 802.1p，range is 0-7 voice 802.1p priority configurate the value of voice 802.1p，the range is 0-7 lan vlan setup lan port vlan open/ forbid port vlan same as wan port id value close...

  • Page 21

    21 2）if change telnet ,http port number ，it’s better set bigger port number than 1024， because 1024 port is system reserved port. 3）http port number is set as 0， then forbid the http service. 4.3.2.4. Time&date according to their own position、configuration time zone and sntp server to automatically ...

  • Page 22

    22 synchronous query inquiry from the server constantly to synchronize ， default 60 second 12 hours system system can switch to 12 hours，default is 24 hours date format configure date format date separator configure date separator summer time set open the daylight saving time configure the daylight ...

  • Page 23

    23 choose which line configuration of the sip account，there are two lines to choose from. Select and click【load】 switch to the line account configuration basic setup registration status phone sip registration status display；if the register will show the registered successfully，otherwise is unregiste...

  • Page 24

    24 open registration configure allow/prohibit registration codecs disable codecs/enable codecs according to the need by navigation on disable codecs/enable codecs list add or remove coding ， and can be used by the priority of the up and down navigation keys to change the coding. Advance sip configur...

  • Page 25

    25 automatic response time when there is a call in，and over time went unanswered，phone will answer it automatically open dialogue timer configure whether to support rfc4028,refresh the sip sessions dialogue timeout configure dialogue timeout open mwi subscription subscribe information after a succes...

  • Page 26

    26 code disable the always forward function on your phone, it will send message to the server, and the server will turn off the function immediately. Busy cfwd on code set the busy cfwd on code, when you choose to enable the busy forward function v on your phone, it will send message to the server, ...

  • Page 27

    27 user agent user agent terminal dtmf type set dtmf sending mode，there are three： dtmf_relay dtmf_rfc2833 dtmf_sip_info different voip service providers may provide different modes. Local port set sip port of each line. Ring type set ring type of each line. Enable via rport enable/disable system to...

  • Page 28

    28 enable display name quote set to make quotation mark to display name as the phone sends out signal, in order to be compatible with server. Enable user=phone enable user=phone by selecting it, it is contained in the invite sip message, in order to be compatible with server. Enable missed call log ...

  • Page 29

    29 network. 4.3.5. Function key 4.3.5.1. Function key 1-4 programmable key in phone software(depend on hardware),you can configurate different feature on each key. You can ref to below indications for each feature, default is na, means without any feature settings. 。 1) type=hot key number 1/2 is th...

  • Page 30

    30 number1 is the main number and number2is the secondary number; when the dial mode is,number1 is the daytime period and number2 is the night time period egs egs,to config the door phone and maintenance the visitor data voice access configuration setting item function initial value open time time f...

  • Page 31

    31 phone calls, input password only. Eanble touchpad provide keyboard function open enable card reader provide card reader function open dial mode select mode corresponds to the first number in one-button call function, mode corresponds to the second number in one-button call function primary /secon...

  • Page 32

    32 after you set the log server, i20t will send log data to the log server. Data format: mar 20 11:17:38 5,0003476426,ic card,i20 ip door phone [note]: “”:log level “mar 20 11:17:38”: happen time “5,0003476426,ic card,i20 ip door phone”:logs have include door open time ,card number/phone number ,ope...

  • Page 33

    33 card issuing mode, and then wave the additional cards into the database, when the procedure completed, wave admin card again to enter normal status.(delete card procedure is same),maximum 10 admin card and 100 visitor card delete administrator to delete admin card, select the card number and clic...

  • Page 34

    34 5.1.1.Specifications: protocol sip 2.0(rfc-3261) chipset broadcom 1190 key key material stainless steel direct-button 1 digital keyboard support voice microphone 1 amplifier 0.5w/8Ω speaker 0.5w/8Ω voice control adjustable fdsp support(aec) voice flow protocol rtp codec g.711, g.729 port power su...

  • Page 35

    35 visitor message ； calling indoor extension for two-way conversation； software upgrading on line； web remote management of terminal malfunction or status； 5.1.3. Schematic diagram 5.2、owner remote opens the voice access controller by voip phone 1）owner calls the voice access controller by voip ter...

  • Page 36

    36 （ 1） issue input available card number to id input field, choose issuer, then press add to add issue administration card. （ 2）issue input available card number to id input field, choose “revocation”, then press add to add delete administration card. （ 3）administration card list 5.3.2 issue user c...

  • Page 37

    37 3) put ic card on the reader sensing area, and make sure the reader responded. 4） choose “normal” in the card reader setting. 5）press “apply”. 6）you can check the issuing records in “door card table” issue the user card (method 2): 1） put issue administration card on the reader sensing area, the ...

  • Page 38

    38 2) press “apply” to enter the state of deleting card, 3) put ic card on the reader sensing area, and make sure the reader responded. 4) choose “normal” in the “card reader setting”. 5）press “apply” . Delete the user card (method 2): 1） put issue administration card on the reader sensing area, the...

  • Page 39

    39 （2）remote visit table.