1 fargo ® hdp8500 card printer printhead replacement guide plt-01638, 1.1 november 2013 © 2013 hid global corporation/assa abloy ab. All rights reserved. 15370 barranca parkway irvine, ca 92618.
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 2 hdp8500 printhead replacement guide l001638 rev 1.1 liability statement do not attempt to operate or repair the direct-to-card printer without adequate training. Any use, operation, or repair in violation of this user guide is ...
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 3 hdp8500 printhead replacement guide l001638 rev 1.1 contacts north america europe, middle east and africa 15370 barranca parkway irvine, ca 92618 usa phone: 800 237 7769 fax: 949 732 2120 tech support: 866 607 7339, #6, m-f 7am...
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 4 hdp8500 printhead replacement guide l001638 rev 1.1 safety messages (review carefully) the purpose of this section is to provide the user with specific replacement procedures for the card printer. Please review standard precaut...
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 5 hdp8500 printhead replacement guide l001638 rev 1.1 installing the printhead kit part number: 088934 tools needed: t10 (torx )driver estimated repair time: 30 minutes important: this procedure can only be performed by authorize...
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 6 hdp8500 printhead replacement guide l001638 rev 1.1 step procedure 5 unplug the rtd wire cable, heater wire cable, and interconnect cable ( with small com board d940171) from the auxiliary board (a920221-10). 6 remove the 3 scr...
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 7 hdp8500 printhead replacement guide l001638 rev 1.1 step procedure 7 remove the ethernet/usb box. Remove two screws from the box base. Pull the box forward and slide to the right then out. Doing this will release the box from t...
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 8 hdp8500 printhead replacement guide l001638 rev 1.1 step procedure 10 gently pull the hoses from the printer. 11 disconnect the 2 fan cable from the fan box. 12 disconnect the mag wires from the back of the fan box. ..
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 9 hdp8500 printhead replacement guide l001638 rev 1.1 step procedure 13 disconnect the wires from the tie wrap on the fan box. 14 disconnect the ribbon cable from the d000445 board ( attached to the fan box riser) set aside the f...
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 10 hdp8500 printhead replacement guide l001638 rev 1.1 step procedure 15 the printhead motor mount (d910052) is now accessible. 16 remove the printhead motor mount (d910052). Remove the one (1) screw that holds the motor mount to...
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 11 hdp8500 printhead replacement guide l001638 rev 1.1 step procedure 17 remove the ground strap of the printhead. 18 unplug the printhead motor mount connectors..
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 12 hdp8500 printhead replacement guide l001638 rev 1.1 step procedure 19 lift out the printhead motor mount assembly. 20 carefully lift out the complete printhead assembly (d910515)..
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 13 hdp8500 printhead replacement guide l001638 rev 1.1 step procedure 21 complete the replacement by doing the following steps. See below for details. A. Replace the complete printhead assembly. Important note: locate the printhe...
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 14 hdp8500 printhead replacement guide l001638 rev 1.1 23 note how the print platen roller slot would fit properly onto the roller bushing, as shown from the back side (below)..
User © 2013 hid global corporation/assa abloy ab. All rights reserved. 15 hdp8500 printhead replacement guide l001638 rev 1.1 step procedure 24 careful when replacing the printhead motor mount (d910052) 25 replace fan box and all cables, ethernet/usb box, and auxiliary board. Replace covers in rever...
