Pagasys series loudspeaker models p-ls2b, p-ls2b-8, pls2c, and pls2c-8 2562390b rev. B 812 printed in u.S.A installation, operation, and maintenance instructions.
Blank page.
3 contents safety messages to installers, users, and maintenance personnel ..... 5 unpacking the loudspeaker ...................................................................6 overview of the pagasys series .........................................................6 certifications ....................
Tables table 1 wattage tap settings ...............................................................13 table 2 example serial number ...........................................................19 table 3 replacement parts .................................................................19.
5 safety messages to installers, users, and maintenance personnel it is important to follow all instructions shipped with this loudspeaker. This loudspeaker is to be installed by trained personnel who is thoroughly familiar with the country electric codes and will follow these guidelines as well as ...
6 pagasys series loudspeaker unpacking the loudspeaker after unpacking the loudspeaker, examine it for damage that may have occurred in transit. If the loudspeaker has been damaged, do not attempt to install or operate it. File a claim immediately with the carrier stating the extent of the damage. I...
7 pagasys series loudspeaker certifications atex certificate number: baseefa10atex0096x iecex certificate number: iecex bas 10.0052x model p-ls2b 0539 ii 2g ex d e mb iib + h2 t5 gb (−50 °c ≤ ta ≤ +70 °c) t6 gb (−50 °c ≤ ta ≤ +55 °c) model p-ls2b-8 0539 ii 2g ex d e mb iib + h2 t5 gb (−50 °c ≤ ta ≤ ...
8 pagasys series loudspeaker specifications electrical: models p-ls2b and p-ls2c audio line voltage: 100 vrms max. Rated power: 25 w models p-ls2b-8 and p-ls2c-8 impedance: 8 ohms max. Rated power: 25 w ambient environment: t5: −50 °c ≤ ta ≤ +70 °c t6: −50 °c ≤ ta ≤ +55 °c pa = 80 kpa to 110 kpa max...
9 pagasys series loudspeaker specific condition of use • except when shown in a certificate as being the internal wiring of the apparatus, not more than one single or multiple-stranded lead shall be connected into either side of any terminal, unless multiple conductors have been joined in a suitable...
10 pagasys series loudspeaker important: the nameplate, which contains cautionary or other information of importance to maintenance personnel, should not be obscured. 1. Select a mounting location that is capable of supporting more than 6 kg (13.2 lb). 2. Use the mounting bracket as a template to sc...
11 pagasys series loudspeaker figure 1 loudspeaker connections for p-ls2b and p-ls2c power tap jumpers earth lug replaceable fuse module audio input from amplifier (+in) to next loudspeaker +out to next loudspeaker −out tapping guide 290a6466 audio input from amplifier (–in).
12 pagasys series loudspeaker figure 2 loudspeaker connections for p-ls2b-8 and p-ls2c-8 290a7003 audio input from amplifier +in earth audio input from amplifier –in to wire the loudspeaker: 1. Loosen the four screws securing the rear cover to the loudspeaker, and remove the cover. 2. Route the lead...
13 pagasys series loudspeaker setting transformer wattage taps the model p-ls2b and p-ls2c loudspeakers have ten wattage tap settings that enable you to select the loudness of each loudspeaker in the system (see table 1 below and figure 3 on page 14). The higher the wattage tap, the louder the speak...
14 pagasys series loudspeaker figure 3 internal wiring for p-ls2b and p-ls2c 290a6467 fuse module black (a) red (b) white (c) 1 2 5 4 3 suppression circuit 6 8 7 11 10 9 12 100v transformer black white speaker – + + – out in current fuse thermal fuse t2 primar y c t1 t3 t2 t1 c.
15 pagasys series loudspeaker figure 4 internal wiring for p-ls2b-8 and p-ls2c-8 speaker white black 1 + – 10 11 12 7 8 9 6 5 4 3 2 290a7001.
16 pagasys series loudspeaker safety messages to maintenance personnel fire/explosion hazard do not open the loudspeaker when it is energized. Failure to observe this warning could result in serious injury or death. Listed below are some important safety instructions and precautions you should follo...
17 pagasys series loudspeaker periodically inspecting the loudspeaker establishing a regular inspection schedule for the loudspeaker extends the life of the loudspeaker and ensures safety. For a list of replacement parts see page 19. • ensure that the the loudspeaker is maintained in line with the r...
18 pagasys series loudspeaker 4. Remove the phillips-head screw securing the fuse module, and remove the module. 5. Reinstall the new fuse module. 6. Replace the rear cover and tighten the screws securing it to approximately 4 n·m (35.4 in-lb). 7. Test the speaker system to verify that it operates p...
19 pagasys series loudspeaker getting technical service and support products returned for repair require a return authorization form. To obtain service for the product, please contact the federal signal service department at +1 708-534-4858. For technical assistance, please call federal signal techn...
Industrial systems 2645 federal signal drive • university park, il 60484-3167 tel: 708-534-4756 • fax: 708-534-4852 email: elp@federalsignal.Com • www.Federalsignal-indust.Com.
