Fender Deluxe 90 DSP Operating Instructions Manual - page 8
w
ww
ww
w.
.f
f e
e n
n d
d e
e r
r.
.c
co
om
m
✧
w
ww
ww
w.
. m
m r
r g
g e
e a
a r
r h
h e
e a
a d
d .
.n
ne
et
t
8
D
D
D
D
e
e
e
e
ll
ll
u
u
u
u
x
x
x
x
e
e
e
e
™
™
™
™
9
9
9
9
0
0
0
0
D
D
D
D
S
S
S
S
P
P
P
P
A
A
A
A
m
m
m
m
p
p
p
p
ll
ll
ii
ii
ff
ff
ii
ii
e
e
e
e
rr
rr
Your new Deluxe™ 90 DSP amplifier delivers
world–class Fender
®
tone and world–standard Fender
®
DSP technology:
• 90W output power @ 4 ohms
• Digital Signal Processing
• 16 FX SELECTIONS
• Separate FX LEVEL and TIME/RATE controls
• Selectable Normal and Drive Channels
with
independent volume and tone controls
• MORE DRIVE pre-amp boost for instant gain
saturation and harmonically rich leads
• PRE AMP OUT and POWER AMP IN jacks
• 3-button FOOTSWITCH (included) enables remote
activation of:
(1) Channel Select, (2) Drive/More Drive, (3) Effects
Thank you for choosing Fender
Thank you for choosing Fender
®
®
—T
—T
one, T
one, T
radition and Innovation—since 1946
radition and Innovation—since 1946
A.
INPUTS - Plug your guitar in here. INPUT 1 is used
for normal electric guitars. INPUT 2 is a lower
sensitivity input for guitars equipped with high
output (active) pickups.
The Normal channel controls (B-E) are operational when
the CH SELECT button
is out, or footswitch
is off.
B.
VOLUME - Adjusts the loudness of the amplifier.
CDE. TREBLE / MID / BASS - Adjusts the tone in the
high / middle / low frequency ranges respectively.
F.
CHANNEL SELECT -
Button OUT
selects the Normal channel
Button IN
selects the Drive channel
The Drive channel controls (G–M), are operational when
the CH SELECT button
is in, or footswitch
is on.
G.
DRIVE - Adjusts the distortion level. Use together with
the Drive channel VOLUME control (I) to adjust the
overall loudness of the amplifier.
H.
MORE DRIVE - Boosts the intensity and range of
the DRIVE control (G).
Button OUT
selects the Drive channel
Button IN
selects More Drive channel
I.
VOLUME - Adjusts loudness of the amplifier
together with the DRIVE control (G).
J.
DRIVE CHANNEL INDICATORS -
Yellow LED ON
Drive channel is active
Red LED ON
More Drive channel is active
KLM. TREBLE / MID / BASS - Adjusts the tone in the
high / middle / low frequency ranges respectively.
N.
FX LEVEL - Adjusts the level of the selected effect.
O.
FX SELECT - Selects the active effect. Each
position defaults to a preset time/rate parameter to
allow for quick auditioning of a common variation
of each effect.
P.
TIME/RATE - Once this knob is nudged, it adjusts
the interval length / modulation speed of the active
effect (see next page).
Q.
POWER INDICATOR - Illuminates when the
amplifier is ON.
R.
POWER - Switches the amplifier ON and
OFF.
S.
POWER CORD SOCKET - Connect the
included power supply cord in
accordance with the voltage and
frequency ratings listed on the rear panel.
T.
PRE AMP OUT/POWER AMP IN -
(1) Effects Loop - Connect PRE
AMP OUT to an effects device
input, then connect the effects
device output to PWR AMP IN.
(2) Multiple Amps - Connect the primary unit’s PRE
AMP OUT to the auxiliary unit’s PWR AMP IN. The
primary unit is used to control all auxiliary units.
(3) Recording or Reinforcement - Connect PRE
AMP OUT to sound equipment’s input.
Both jacks use a TS (Tip-Sleeve) standard
type plug for connections. PRE AMP OUT includes
onboard tone shaping and DSP effects processing.
U.
FOOTSWITCH - Connect the 3-button Fender
®
footswitch (included) to this jack to enable remote
switching of CH SELECT, DRIVE/MORE DRIVE,
and EFFECTS. When plugged in, the footswitch
overrides the corresponding panel controls.
PWR AMP
IN
PRE AMP
OUT
FOOT
SWITCH
P
P
P
P
a
a
a
a
n
n
n
n
e
e
e
e
ll
ll
F
F
F
F
u
u
u
u
n
n
n
n
c
c
c
c
tt
tt
ii
ii
o
o
o
o
n
n
n
n
s
s
s
s