Fender Passport PD250 Plus Owner's Manual - page 14
14
Part Number
069-3001-000 PD-250+ 120V US
069-3001-900 PD-250+ 120V DS
069-3001-930 PD-250+ 240V AUS
069-3001-940 PD-250+ 230V UK
069-3001-960 PD-250+ 230V EUR
069-3001-970 PD-250+ 100V JPN
Frequency Response
50 Hz to 30 kHz ± 1 dB (at speaker output)
30 Hz to 20 kHz ± 1 dB (at send output)
Distortion
< 0.5% 20 Hz to 20 kHz (at speaker output)
< 0.1% 20 Hz to 20 kHz (at send output)
System Signal to Noise Ratio
> 85 dB, “A” WTD
Power Output
250 W (125 W/ch @ 8ohm per channel)
Input Impedance
(Channels 1-2-3-4 XLR and 1/4”)
“Mic” switch position: 2 k ohm
“Line” switch position: 66 k ohm
(Phono and Stereo Channel 1/4”)
78 k ohm
Max. Input Level
Mic:
-11 dBu
Line:
20 dBu
Stereo:
26 dBu
Return Input Impedance
47k ohm
Fuse type
T6.3AH, 250V
Passport System
Width:
840 mm (33.7 in.)
Height:
615 mm (24.2 in.)
Depth:
300 mm (11.8 in.)
Weight:
24 kgs (53 lbs)
Speakers
Width:
300 mm (13.4 in.)
Height:
610 mm (24.2 in.)
Depth:
300 mm (11.8 in.)
Weight:
7.3 kgs (16 lbs)
Power Tower
Width
185 mm (7.3 in.)
Height
615 mm (24.2 in.)
Depth
300 mm (11.8 in.)
Weight
9.5 kgs (21 lbs)
Tower Footprint
350 x 300 mm (9.5 x 11.75 in.)
Microphone
Dynamic Cardioid, balanced
Microphone Cable
XL -Male to XL-Female, 6 m (20 feet)
Speaker Cables
1/4 in. to 1/4 in., 9 m (27 feet)
0 dBu is referenced to 0.775 volts rms
PoWER ToWER™
In setting up the system, the Passport Mixing
console should ideally be placed where system
performance can be evaluated by the operator.
If no ongoing adjustments will be necessary, the
mixer may be placed conveniently and where the
cable lengths allow.
Take care to place the Power Tower where the
cables will not trip anyone. All cables should be
carefully secured.
The storage compartment in the rear of the
Tower can hold cables, microphones and other
system parts. To open simply slide the catch
upwards and pull open.
The mains (AC) fuse holder is under the IEC
(power cord) socket on the right rear of the
Tower. To change a fuse, remove the IEC plug
and, using an appropriate tool pull out the fuse
holder. Note there is a spare fuse in the fuse
holder; the Passport utilizes a T6.3AH, 250V fuse.
Only replace fuses with one of an identical value
and size.
The Passport System is weather resistant in
its packed transport mode. However, when
operating outdoors, take care to fully protect the
Power Tower in the event of exposure to rain.
Remember to allow free air flow through the
air inlet located at the bottom of the rear
panel on the Passport power tower.
SpecIfIcatIoNS
Set-up aNd coNNectIoNS