- DL manuals
- Ferroli
- Fan
- TEMPRA 30
- Installation And Operation Manual
Ferroli TEMPRA 30 Installation And Operation Manual
Summary of TEMPRA 30
Page 1
Installation and operation manual top fan plus fan coil en.
Page 2
Dear customer, thank you for having purchased a ferroli fan coil. It is the result of many years experience, particular research and has been made with top quality materials and higlly advanced technologies.The ce mark guaranteed thats the appliances meets european machine directive requirements reg...
Page 3
Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 general warranty conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 descript...
Page 4
Declaration of conformity 4 the company hereby declares that the machine in question complies with the matters prescribed by the following directives: • machinery directive 2006/42/ec • electromagnetic compatibility directive (emc) 2004/108/ec • low voltage directive (lvd) 2006/95/ec general warrant...
Page 5
5 description of the appliance purpose of the machine the convector fan is an appliance that treats the air in the room in both summer (bank supplied with cold water min. 6°c) and winter (bank supplied with hot water max 85°c). Available versions and installation methods the range of centrifugal con...
Page 6
Description of the appliance 2: vm-f - convector fan with cabinet and frontal intake consisting of a sheet metal cabinet, a delivery grille with doors to access a panel if installed in thermoplastic mate- rial, plus an air filter that can be regenerated installed in the front grille, made of plastic...
Page 7
Description of the appliance 3: vn - convector fan without cabinet for built-in installation without cabinet. Includes a filter which can be regenera- ted, mounted on a metal frame with covering profile in pla- stic material. It can be fitted with a series of accessories to suit the installation req...
Page 8
General specifications overall dimensions of model that intakes from below overall dimensions of model that intakes from the front 100 554 a 220 a 554 220 model 15 20 30 40 50 60 80 100 120 a (mm) 690 690 940 940 1190 1190 1190 1440 1440 weight (kg) 14 14 20 20 27 27 27 34 34 model 15 20 30 40 50 60...
Page 9
General specifications overall dimensions of ducted model 494 a 216 Ø 16 overall dimensions of bracketing 278 Ø 16 60 494 137.5 137.5 a overall dimensions if applicable 77.5 model 15 20 30 40 50 60 80 100 120 a (mm) 474 474 724 724 974 974 974 1224 1224 weight (kg) 11 11 15 15 22 22 22 29 29 model 1...
Page 10
General specifications main bank wet connections supplementary bank wet connections (only for 3row version) 246.5 494 100 494 100 52 44 99.5 161 145.6 165 49.5 10
Page 11
General specifications key to wiring diagram mt = ground terminal mo = main terminal board cn1 = motor connector cn = control connector rem = remote control for function changes (230v voltage rating) ec = economy function key ma = brown wire gr = grey wire g/v = yellow/green wire mrs = red wire (3rd...
Page 12
General specifications wiring diagrams wiring diagram of heat/cool function and speed selector command (on appliance and wall): note: commutator • installation on machine and wall • selector off / summer mode / winter mode • three-speed selector version on machine w all-mounted version heat/cool fun...
Page 13
General specifications wiring diagrams wiring diagram of basic model ambient thermostat, heat/cool function and speed selector command (on board machi- ne and wall): note: basic thermostat • installation on machine and wall • on/off selector • summer mode / winter mode / automatic mode selector • th...
Page 14
General specifications wiring diagrams wiring diagram of advanced mod. Economy function, thermostat, heat/cool function and speed selector command (on machine and wall): note: advanced thermostat • installation on machine and wall • on/off selector • summer mode / winter mode / automatic mode select...
Page 15
Installation packing and contents the convector fans are shipped in standard packaging consisting of a cardboard box inside which angular pieces of polystyrene are fitted to protect the appliance from damage during the handling phase. The cardboard box contains. • 1 convector fan • 1 cardboard templ...
Page 16
Installation fig.1 recommendations for correct installation • horizontal installation: - the appliance must slant at least 2° to allow the condensation to flow away. See fig.1. Fig.2 - the appliance must slant slightly towards the downflow side to prevent water from stagnating in the tray. See fig.2...
Page 17
Installation operations prior to installation comply with the following instructions before beginning to install the appliance: - make sure that all parts of the convector fan are in a perfect condition. - make sure that the appliance has not sustained damage during transport. Immediately notify the...
Page 18
Installation accessory parts normally available on the market and required for installation the following items are also required: - plumbing unions - anti-condensation tape - adhesive tape - copper pipe of flexible steel pipe with built-in unions - Ø 8mm press-in plugs how to install the appliance ...
Page 19
Installation bank rotation (only for 3row version) if the bank must be turned to suit the plumbing system, proceed in the following way after having removed the front panel (when installed): 1. Disconnect the electricity main and make sure that no one is able to connect it again during the installat...
Page 20
Installation electrical connections warning: always make sure that the electric power source has been disconnected before proceeding with any operation. Refer to the wiring diagrams on pages 10-13 for the electrical connections. The appliance must be connected to the power supply by means of an omni...
Page 21
Operation how to operate the convector fan the convector fan is operated by means of a control panel (available in three versions) which can be fixed to the wall or machine. On this, it is hidden under one of the two side covers (the control panel will be installed on either the left or right side, ...
Page 22
Routine maintenance general recommendations for cleaning warning: remove the power plug from the electricity main before servicing or cleaning the convector fan. Never pour water on to the convector fan. It could damage the mechanical or electrical parts. When the convector fan is cleaned, it is abs...
Page 23
Assistance and spare parts assistance and spare parts ask the dealer where the appliance was purchased for our nearest after-sales service center or consult the yellow pages under the “conditioners” or “gas boilers” headings. Routine maintenance troubleshooting fault probable cause remedy insufficie...
Page 24
Technical data plate the figure on the left illustrates the identification plate of the unit a - trademark b - model c - code d - serial number e - power delivery during cold mode operation f - power delivery during hot mode operation g - cooling power input h - heating power input i - reference sta...
Page 25
Note.
Page 26
Note.
Page 27
27.
Page 28
Ferroli spa ¬ 37047 san bonifacio (verona) italy ¬ via ritonda 78/a tel. +39.045.6139411 ¬ fax +39.045.6100933 ¬ www.Ferroli.It cod. 3qe28520