Summary of 418
Page 1
Operation and maintenance manual reversible air drill art. 0418 translation of the original instructions fervi.Com.
Page 2: Preface
Hardware page 2 of 13 preface please ensure you have read this manual before any operation translation of the original instructions it is compulsory to read this instruction manual before starting operation. The guarantee that the machine will function and perform properly is strictly dependent upon...
Page 3: Contents
Hardware page 3 of 13 contents 1 general safety instructions............................................................. 4 1.1 risks associated with the work area ............................................................................4 1.2 risks associated with the presence of rotating and/or ...
Page 4: Parts
Hardware page 4 of 13 1 general safety instructions 1. During use, maintain control of the tool. The operators represent the most important aspect of safety. Working cautiously and carefully is the best protection against the risk of injury. 2. The pneumatic tool should not be used and repaired by s...
Page 5: 1.4 Technical Assistance
Hardware page 5 of 13 1.3 personal protective equipment when using the pneumatic tool, always wear the following: safety shoes; work gloves; hearing protection (cap, earplugs, etc.); protective goggles. 1.4 technical assistance for any problems and/or concerns, please contact, without hesitation, th...
Page 6: Fervi.Com
Hardware page 6 of 13 2 description of the drill and intended use the air drill is a portable pneumatic tool, to be used for drilling holes in various kinds of material such as wood, metal, plastic, etc. The drill is made up of the following parts (see figure 1): 1 "gun" shaped body, which contains ...
Page 7: 2.2 Pictograms
Hardware page 7 of 13 2.2 pictograms attached to each machine there is an obligation pictogram: carefully read the operation and maintenance manual before using the tool! Figure 2 – close-up of the pictograms 2.3 identification plate there is an identification plate on each machine, which shows the ...
Page 8: Fervi.Com
Hardware page 8 of 13 3 improper uses and precautions it is strictly forbidden !! to allow the tool to be used by untrained personnel and those who have not read the instruction manual; to use the tool for different purposes and uses other than those for which it was designed, i.E. Drilling hole...
Page 9: 4 Commissioning
Hardware page 9 of 13 4 commissioning 1. Remove the air inlet cap, then screw the supplied nozzle into the hole: 1/4" npt male quick-release coupling 2. Put a few drops of lubricating oil (without resin acid) in the air inlet nozzle. 3. Check the flexible air supply hose. If it is damaged, broken, t...
Page 10: 5 How To Use
Hardware page 10 of 13 5 how to use 5.1 mounting the drill bits crushing and cutting before mounting and/or removing the cutting bits, always disconnect the air supply hose. Protective gloves before mounting and/or removing the cutting bits, wear suitable protective gloves. 1. Insert a cutting tip (...
Page 11: Precautions For Use
Hardware page 11 of 13 precautions for use when drilling on small or irregularly shaped objects, secure the work piece in a vice with soft jaws. After mounting the cutting bit and connecting the flexible compressed air supply hose, hold the drill by its "gun" handle. Turn the selector lever to choos...
Page 12: Fervi.Com
Hardware page 12 of 13 6 maintenance and cleaning the purpose of this section is to provide all the information on maintenance procedures and frequency that the drill requires. Intervention frequency daily weekly 1. General visual inspection x 2. General cleaning x 3. Clean the air outlet nozzle x 4...
Page 13: Fervi.Com
Hardware page 13 of 13 7 bill of materials and spare parts ref. Description ref. Description 0418/01 body of the machine 0418/19 rear cylinder head 0418/02 rotation direction lever. 0418/20 pin 0418/03 screw 0418/21 blade 0418/04 o-ring 0418/22 rotor 0418/05 pin 0418/23 cylinder 0418/06 trigger 0418...