1. DL manuals
  2. Fervi
  3. Grinder
  4. 570
  5. User And Maintenance Manual

Fervi 570 User And Maintenance Manual

Manual is about: Fervi Axial Grinder Set with Sanding Attachments

Summary of 570

  • Page 1

    User and maintenance manual axial grinder set with sanding attachments art. 0570 translation of the original instructions fervi.Com.

  • Page 2: Foreword

    Hardware page 2 of 13 foreword read this manual before operation translation of the original instructions reading this instruction manual is required before operating any of the machinery. The assurance of smooth operation and full compliance of machine performance is strictly dependent on the rigor...

  • Page 3: Index

    Hardware page 3 of 13 index 1 general safety instructions............................................................. 4 1.1 risks associated with the work area ............................................................................4 1.2 risks associated with the presence of rotating and/or mov...

  • Page 4: Parts

    Hardware page 4 of 13 1 general safety instructions  during use, maintain control of the tool.  the operators represent the most important aspect of safety. To better protect against the risk of injury, work cautiously and carefully.  when a fault / defect is detected, immediately disconnect the ...

  • Page 5: Use

    Hardware page 5 of 13 2 description of the grinder and intended use the grinder (art. 0570) is a portable pneumatic tool, to be used for grinding, finishing and bevelling small surfaces. By changing out the abrasive tools (grinding wheels), it is possible to grind or polish different materials, such...

  • Page 6: 2.2 Identification Plate

    Hardware page 6 of 13 2.2 identification plate there is an identification plate on each machine, which shows the following data:  the name and address of the manufacturer;  model/serial number;  year of construction;  maximum working pressure;  nominal rotation speed. Figure 2 – identification ...

  • Page 7: 4 Commissioning

    Hardware page 7 of 13 4 commissioning 1. Remove the air inlet cap, then screw the supplied nozzle into hole (ref. 8): 1/4" npt male quick-release coupling 2. Put a few drops of lubricating oil (without resin acid) in the air inlet nozzle. 3. Check the flexible air supply hose. 4. If it is damaged, b...

  • Page 8: 5 How To Use

    Hardware page 8 of 13 5 how to use 5.1 attaching the abrasive tools crushing and cutting before attaching and/or removing the grinding wheels, always remove the air supply hose. Protective gloves before attaching and/or removing the grinding wheels, wear suitable protective gloves. 1. Choose the gri...

  • Page 9: Crushing And Cutting

    Hardware page 9 of 13 crushing and cutting  always be sure to insert the shaft of the grinding wheel into the hole of the tool chuck by at least 10mm.  always make sure that the tool is assembled correctly while trying to manually remove it from the grinder.  if it is too short or incorrectly tig...

  • Page 10: 5.2 Power On / Off

    Hardware page 10 of 13 5.2 power on / off (personal protective equipment) ppe before using the grinder, wear suitable work clothing, gloves, shoes and protective goggles. Also wear a mask if you work with materials that produce dust or fumes. Also wear protective devices for the ears (hearing protec...

  • Page 11: Emergency

    Hardware page 11 of 13 figure 7 – turning on the grinder (a: disabling the safety – b: press the lever). The grinder's start lever is a continuous hold lever, in the sense that the function controlled (i.E., the rotation of the grinding wheel) is active as long as the lever itself is kept pressed. T...

  • Page 12: Fervi.Com

    Hardware page 12 of 13 6 maintenance and cleaning the purpose of this chapter is to provide all the information on maintenance procedures and their frequency as required by the machine. Action frequency daily weekly 1. General visual inspection x 2. General cleaning x 3. Clean the air outlet nozzle ...

  • Page 13: Fervi.Com

    Hardware page 13 of 13 7 bill of materials and spare parts no. Description no. Description 0570/01 screw 0570/17 back closure 0570/02 o-ring 0570/18 linchpin 0570/03 o-ring 0570/19 rotor vane 0570/04 air regulator 0570/20 rotor 0570/05 spring 0570/21 cylinder 0570/06 air valve bushing 0570/22 conica...