1. DL manuals
  2. FFC
  3. Snow Blower
  4. 11048
  5. Operator And Parts Manual

FFC 11048 Operator And Parts Manual

Manual is about: HYDRAULIC SNOW BLOWER

Summary of 11048

  • Page 1

    1 800-456-7100 i www.Paladinattachments.Com 2800 n. Zeeb rd., dexter, mi. 48130, united states of america copyright © operator’s and parts manual hydraulic snow blower manual number: 51-4694 models: std: 11048, 11060, 11072, 11078 & 11084 (a through e) hf: 11072, 11078, 11084 & 11096 (f through h) r...

  • Page 2

    2 notes.

  • Page 3: Table of Contents

    3 table of contents preface .....................................................................................................................................................4 safety statements ..........................................................................................................

  • Page 4: Preface

    4 general information this product was carefully designed and manufactured to give you many years of dependable service. Only minor maintenance (such as cleaning and lubricating) is required to keep it in top working condition. Be sure to observe all maintenance procedures and safety precautions in ...

  • Page 5: Safety Statements

    5 danger! This signal word is used where serious injury or death will result if the instructions are not followed properly. Warning! This signal word is used where serious injury or death could result if the instructions are not followed properly. Caution! This signal word is used where minor injury...

  • Page 6: General Safety Precautions

    6 warning! Protect against flying debris always wear proper safety glasses, goggles or a face shield when driving pins in or out or when operation causes dust, flying debris, or any other hazardous material. Warning! Lower or support raised equipment do not work under raised booms without supporting...

  • Page 7: General Safety Precautions

    7 general safety precautions warning! Do not modify machine or attachments modifications may weaken the integrity of the attachment and may impair the function, safety, life and performance of the attachment. When making repairs, use only the manufacturer’s genuine parts, following authorized instru...

  • Page 8

    8 equipment safety precautions warning! Remove paint before welding or heating. Hazardous fumes/dust can be generated when paint is heated by welding, soldering or using a torch. Do all work outside or in a well ventilated area and dispose of paint and solvent properly. Remove paint before welding o...

  • Page 9: Safety Decal Locations

    9 instructions • keep all safety signs clean and legible. • replace all missing, illegible, or damaged safety signs. • replacement parts for parts with safety signs attached must also have safety signs attached. • safety signs are available, free of charge, from your dealer or from ffc. Placement or...

  • Page 10: Safety Decals

    10 safety decals 6. 50-10017 warning! Read manual 3. 50-0724 warning! High pressure fluid 5. 50-0737 warning! Pinch point 12. Rdl3161 danger! Rotating auger 13. Rdl3163 danger! Rotating fan 10. Rdl3131 red reflective marker 4. 50-0727 warning! Flying objects.

  • Page 11: Installation & Set-Up

    11 installation & set-up warning! Read manual prior to installation improper installation, operation, or maintenance of this equipment could result in serious injury or death. Operators and maintenance personnel should read this manual, as well as all manuals related to this equipment and the prime ...

  • Page 12: Installation & Set-Up

    12 caution! Failure to obey the following procedures may result in personal injury. • to avoid electrical shock during the wiring harness installation, remove the ground cable from the battery of your prime mover. 6. Remove the ground cable from the negative (-) post of your prime mover's battery. 7...

  • Page 13: Installation & Set-Up

    13 installation & set-up read and understand all safety statements read all safety decals and safety statements in all manuals before beginning any snow blower setup. Know and obey all osha regulations, local laws, and other professional guidelines for your operation. Know and follow good work pract...

  • Page 14: Operation

    14 operation gehl joy stick deflector up = button a deflector down = button b chute rotation left = button c plus button a chute rotation right = button c plus button b right joystick left joystick caterpillar joy stick d c a b deflector up: button a deflector down: button b chute rotation right: bu...

  • Page 15: Operation

    15 operation gehl rt track loader joy stick chute rotation left: button a chute rotation right: button b deflector up: button c deflector down: button d a c d b.

  • Page 16: Operation

    16 operation c a d b case/new holland joy stick komatsu joy stick k c i t s y o j right k c i t s y o j left d t t a k c o l d w f v e r a b c n r o h e h t . W o lf d w f e lt t il a t e g , e lt t il a s s e r p e d . W o lf e r o m e h t , s s e r p e d u o y e r o m . W o lf x a m = y a w e h t ...

  • Page 17: Operation

    17 read and understand all safety statements read all safety decals and safety statements in all manuals prior to operating or working on this equipment. Know and obey all osha regulations, local laws, and other professional guidelines for your operation. Know and follow good work practices when ass...

  • Page 18: Operation

    18 2. To maximize the snow moving capabilities, try to remove snow before the accumulation reaches 12 inches. Notice! Placing the loader arm hydraulics in the float position decreases the prime mover's capability to provide the desired hydraulic flow and pressure to your snow blower's motors. Snow t...

  • Page 19: Operation

    19 hydraulic snow blower operation caution! Failure to obey the following procedures may result in personal injury. • avoid pinch points and be aware of rotating parts when manually turning fan or auger. E) the fan can then be manually turned in a reverse rotation, allowing the foreign object to be ...

  • Page 20: Operation

    20 lift points lifting points are identified by lifting decals where required. Lifting at other points is unsafe and can damage attachment. Do not attach lifting accessories around cylinders or in any way that may damage hoses or hydraulic components. • attach lifting accessories to unit at recommen...

  • Page 21: Maintenance

    21 maintenance read and understand all safety statements read all safety decals and safety statements in all manuals prior to operating or working on this equipment. Know and obey all osha regulations, local laws, and other professional guidelines for your operation. Know and follow good work practi...

  • Page 22: Maintenance

    22 maintenance read and understand all safety statements read all safety decals and safety statements in all manuals prior to operating or working on this equipment. Know and obey all osha regulations, local laws, and other professional guidelines for your operation. Know and follow good work practi...

  • Page 23: Troubleshooting

    23 problem possible cause possible solution auger will not rotate hoses installed incorrectly switch quick coupler fittings hydraulic valve on skid steer not engaged see skid steer operator's manual for auxiliary operation procedure worn, damaged, insufficient or inadequate pump repair or replace hy...

  • Page 24: Product Specifications

    24 product specifications notice! Exceeding any of the maximum recommended prime mover specifications can result in damage to this product and will void all ffc warranties. Description specifications all models motor kit (a) all models motor kit (c) (d) or (e) all models motor kit (f) (g) or (h) wei...

  • Page 25: Bolt Torque Specifications

    25 bolt torque specifications note - nylock nuts are utilized when greater resistance to vibrating loose is required, and greater operating temperatures are not a factor. In addition, like lock nuts, nylock nuts have a safety feature that if the bolt does vibrate loose, the nut will remain on the sc...

  • Page 26: Warranty

    26 warranty limited warranty except for the excluded products as described below, all new products are warranted to be free from defects in material and/or workmanship during the warranty period, in accordance with and subject to the terms and conditions of this limited warranty. 1. Excluded product...

  • Page 27: Notes

    27 notes.

  • Page 28

    28 standard flow housing assembly 32 32 25 17 27 33 22 35 12 25 32 32 29 34 27 15 27 33 11 23 5 24 28 1 19 4 30 13 31 32 2 1 26 20 3 14.

  • Page 29

    29 standard flow housing assembly item part qty description 1. 07-1763 8 washer, flat, 1/2 sae, gr8 2. 07-10126 22 washer, flat, 1 5/8 sae, gr5 3. 13-17276 1 weld, auger, standard (48 inch) 13-51790 1 weld, auger, standard (60 inch) 13-51789 1 weld, auger, standard (72 inch) 13-52905 1 weld, auger, ...

  • Page 30

    30 standard flow chute assembly 17 18 20 24 5 13 23 6 10 11 14 15 4 21 16 21 21 15 19 25 12 23 1 20 24 22 17 9 7 2 8 3.

  • Page 31

    31 standard flow chute assembly item part qty description 1. 07-3022 1 screw, hhc, gr8, 1/4-20 x 2 2. 07-3432 4 screw, hhc, gr8, 1/4-20 x 3/4 3. 07-4033 4 nut, hex, nylock, gr8, 1/4-20 4. 13-17292 1 gear cover 5. 13-17294 1 weld, chute 6. 13-17487 4 plate, chute, spacer 7. 13-18453 4 rod, .25 x 9.97...

  • Page 32

    32 48-60 inch a,c,d,e series standard hydraulic components green wire plug yellow wire plug red wire plug brown wire plug 2 20 2 15 15 4 16 7 10 19 1 1 13 11 14 6 12 8 16 6 3 3 3 3 9 10 5 5 22 7 18 30 28 24 17 33 35 27 31 23 36 33 26 32 29 25 34 21.

  • Page 33

    33 standard hydraulic components 48-60 inch a,c,d,e series item part qty description 1. 03-1953 2 elbow, 90º, 6mf-10mb 2. 03-2092 2 elbow, 90º, 6mb-6mfs 3. 03-2115 4 elbow, 45º, 6mb-6mf 4. 03-2126 1 elbow, 90º, 10mb-10mf 5. 03-4316 2 hose, .25 x 20, 6ffs-6ffs, 3k 6. 03-4372 2 tee, 10mf-10mf-10ff 7. ...

  • Page 34

    34 72-84 inch d & e series standard hydraulic components green wire plug yellow wire plug red wire plug brown wire plug 2 20 2 15 15 4 16 14 10 19 1 1 12 18 13 6 11 8 16 6 3 3 3 3 9 5 5 22 7 33 25 32 29 26 36 17 33 21 35 27 31 23 30 28 24 34.

  • Page 35

    35 standard hydraulic components item part qty description 1. 03-1953 2 elbow, 90º, 6mf-10mb 2. 03-2092 2 elbow, 90º, 6mb-6mfs 3. 03-2115 4 elbow, 45º, 6mb-6mf 4. 03-2126 1 elbow, 90º, 10mb-10mf 5. 03-4316 2 hose, .25 x 20, 6ffs-6ffs, 3k 6. 03-4372 2 tee, 10mf-10mf-10ff 7. 03-5256 1 hose, .5 x 51, 1...

  • Page 36: Standard Mounting Assembly

    36 standard mounting assembly 10 8 7 3 1 8 4 9 10 2 5 14 11 13 12 6 item part qty description 1. 07-7714 1 screw, hhc, gr5, 5/8-11 x 1 1/2 2. 105840 1 washer, fender, .34 x 1.5 x 10ga 3. Laf6535 1 weld, back plate (contact dealer for correct model) 4. P851105 1 washer, lock, 5/16 5. Rhw1105 1 screw,...

  • Page 37: Notes

    37 notes.

  • Page 38: High Flow Housing Assembly

    38 high flow housing assembly 34 30 35 37 31 21 2 14 38 6 27 34 20 6 10 27 18 31 37 2 31 37 22 12 36 28 29 19 29 24 36 28 13 11 34 30 35 32 26 17 34 30 35 39 4 3 5 15 40 1 33 41 16 7 single motor.

  • Page 39: High Flow Housing Assembly

    39 high flow housing assembly item part qty description 1. 07-1177 1 clamp, rubber coat, 1/2 x 3/4 2. 07-1763 8 washer, flat, gr8, 1/2 3. 07-3273 1 washer, lock, split, medium, 5/16 4. 07-3298 1 clamp, rubber coat, 1 1/2 x 3/4 5. 07-3436 1 screw, hhc, gr8, 5/16-18 x 3/4 6. 07-10126 22 washer, flat, ...

  • Page 40: High Flow Housing Assembly

    40 high flow housing assembly dual motor 12 36 6 6 7 26 19 30 35 2 30 35 21 10 34 27 28 20 34 27 11 8 32 29 33 18 32 29 33 37 4 3 5 13 38 1 31 39 14 9 28 24.

  • Page 41: High Flow Housing Assembly

    41 high flow housing assembly dual motor item part qty description 1. 07-1177 1 clamp, rubber coat, 1/2 x 3/4 2. 07-1763 8 washer, flat, gr8, 1/2 3. 07-3273 1 washer, lock, split, medium, 5/16 4. 07-3298 1 clamp, rubber coat, 1 1/2 x 3/4 5. 07-3436 1 screw, hhc, gr8, 5/16-18 x 3/4 6. 07-10126 22 was...

  • Page 42: High Flow Chute Assembly

    42 high flow chute assembly 12 16 5 16 12 11 15 6 13 15 4 8 9 12 16 2 10 1 3 8 15 14 7 17 item part qty description 1. 07-3022 1 screw, hhc, gr8, 1/4-20 x 2 2. Laf6527 1 weld, deflector 3. Laf6551 1 plastic deflector liner 4. Laf6565 1 liner, chute, plastic 5. Laf6566 1 chute rotation pad 6. Laf6568...

  • Page 43: High Flow Mounting Assembly

    43 high flow mounting assembly 3 1 3 2 4 5 4 5 item part qty description 1. Laf6594 1 weld, back plate (contact dealer for correct model) 2. Laf1421 1 gasket, hose hole 3. Rhw1604 6 screw, hhc, gr5, 5/8-11 x 2 4. Rhw5632 6 washer, flat, gr5, 5/8 5. Rhw7607 6 nut, top lock, flange, gr8, .63-11.

  • Page 44: F Series

    44 high flow hydraulic components f series 2 15 2 15 25 23 6 6 12 5 16 12 10 14 7 17 18 10 19 28 24 20 11 1 4 21 26 9 1 8 13 5 5 8 3 5 35 34 38 36 33 30 22 31 33 30 35 22 34 38 27 39 37 29 22 34 38 32.

  • Page 45: F Series

    45 high flow hydraulic components f series item part qty description 1. 03-1945 2 fitting, 12mb-12mfs 2. 03-2092 2 elbow, 90º, 6mb-6mfs 3. 03-2177 1 elbow, 90º, 12mb-12mfs 4. 03-2182 1 elbow, 45º, 12mb-12mfs 5. 03-2291 4 fitting, 6mb-6mfs 6. 03-2564 2 fitting, 6mf-10mb 7. 03-3135 1 tee, 12mb-12mf-12...

  • Page 46: G Series

    46 high flow hydraulic components g series 3 22 26 29 20 24 6 12 5 15 2 14 16 17 10 18 28 25 19 11 7 4 21 29 9 1 8 13 20 39 35 36 36 35 39 39 23 35 34 31 32 23 36 6 5 5 5 12 37 34 31 23 35 39 27 40 33 38 30 22 3.

  • Page 47: G Series

    47 high flow hydraulic components g series item part qty description 1. 03-1945 1 fitting, 12mb-12mfs 2. 03-1950 1 tee, 12mf-12mf-12mb 3. 03-2092 2 elbow, 90º, 6mb-6mfs 4. 03-2182 1 elbow, 45º, 12mb-12mfs 5. 03-2291 4 fitting, 6mb-6mfs 6. 03-2564 2 fitting, 6mf-10mb 7. 03-3135 2 tee, 12mb-12mf-12mf ...

  • Page 48: H Series

    48 high flow hydraulic components h series 2 23 2 23 26 27 20 25 5 12 4 16 13 15 3 17 18 10 22 29 34 11 11 6 3 21 27 8 1 7 9 13 1 8 14 19 41 37 38 41 37 24 39 36 31 41 37 38 39 36 41 31 24 37 24 24 33 32 38 37 24 41 35 28 42 40 30 5 4 4 12 4 24 19 21 11.

  • Page 49: H Series

    49 high flow hydraulic components h series item part qty description 1. 03-1945 2 fitting, 12mb-12mfs 2. 03-2092 2 elbow, 90º, 6mb-6mfs 3. 03-2182 2 elbow, 45º, 12mb-12mfs 4. 03-2291 4 fitting, 6mb-6mfs 5. 03-2564 2 fitting, 6mf-10mb 6. 03-3135 1 tee, 12mb-12mf-12mf 7. 03-6343 1 hose, .75 x 80, 12ff...