1 800-456-7100 i www.Paladinattachments.Com 2800 n. Zeeb rd., dexter, mi. 48130, united states of america copyright © operator’s and parts manual hydraulic snow blower manual number: 51-4694 models: std: 11048, 11060, 11072, 11078 & 11084 (a through e) hf: 11072, 11078, 11084 & 11096 (f through h) r...
2 notes.
3 table of contents preface .....................................................................................................................................................4 safety statements ..........................................................................................................
4 general information this product was carefully designed and manufactured to give you many years of dependable service. Only minor maintenance (such as cleaning and lubricating) is required to keep it in top working condition. Be sure to observe all maintenance procedures and safety precautions in ...
5 danger! This signal word is used where serious injury or death will result if the instructions are not followed properly. Warning! This signal word is used where serious injury or death could result if the instructions are not followed properly. Caution! This signal word is used where minor injury...
6 warning! Protect against flying debris always wear proper safety glasses, goggles or a face shield when driving pins in or out or when operation causes dust, flying debris, or any other hazardous material. Warning! Lower or support raised equipment do not work under raised booms without supporting...
7 general safety precautions warning! Do not modify machine or attachments modifications may weaken the integrity of the attachment and may impair the function, safety, life and performance of the attachment. When making repairs, use only the manufacturer’s genuine parts, following authorized instru...
8 equipment safety precautions warning! Remove paint before welding or heating. Hazardous fumes/dust can be generated when paint is heated by welding, soldering or using a torch. Do all work outside or in a well ventilated area and dispose of paint and solvent properly. Remove paint before welding o...
9 instructions • keep all safety signs clean and legible. • replace all missing, illegible, or damaged safety signs. • replacement parts for parts with safety signs attached must also have safety signs attached. • safety signs are available, free of charge, from your dealer or from ffc. Placement or...
10 safety decals 6. 50-10017 warning! Read manual 3. 50-0724 warning! High pressure fluid 5. 50-0737 warning! Pinch point 12. Rdl3161 danger! Rotating auger 13. Rdl3163 danger! Rotating fan 10. Rdl3131 red reflective marker 4. 50-0727 warning! Flying objects.
11 installation & set-up warning! Read manual prior to installation improper installation, operation, or maintenance of this equipment could result in serious injury or death. Operators and maintenance personnel should read this manual, as well as all manuals related to this equipment and the prime ...
12 caution! Failure to obey the following procedures may result in personal injury. • to avoid electrical shock during the wiring harness installation, remove the ground cable from the battery of your prime mover. 6. Remove the ground cable from the negative (-) post of your prime mover's battery. 7...
13 installation & set-up read and understand all safety statements read all safety decals and safety statements in all manuals before beginning any snow blower setup. Know and obey all osha regulations, local laws, and other professional guidelines for your operation. Know and follow good work pract...
14 operation gehl joy stick deflector up = button a deflector down = button b chute rotation left = button c plus button a chute rotation right = button c plus button b right joystick left joystick caterpillar joy stick d c a b deflector up: button a deflector down: button b chute rotation right: bu...
15 operation gehl rt track loader joy stick chute rotation left: button a chute rotation right: button b deflector up: button c deflector down: button d a c d b.
16 operation c a d b case/new holland joy stick komatsu joy stick k c i t s y o j right k c i t s y o j left d t t a k c o l d w f v e r a b c n r o h e h t . W o lf d w f e lt t il a t e g , e lt t il a s s e r p e d . W o lf e r o m e h t , s s e r p e d u o y e r o m . W o lf x a m = y a w e h t ...
17 read and understand all safety statements read all safety decals and safety statements in all manuals prior to operating or working on this equipment. Know and obey all osha regulations, local laws, and other professional guidelines for your operation. Know and follow good work practices when ass...
18 2. To maximize the snow moving capabilities, try to remove snow before the accumulation reaches 12 inches. Notice! Placing the loader arm hydraulics in the float position decreases the prime mover's capability to provide the desired hydraulic flow and pressure to your snow blower's motors. Snow t...
19 hydraulic snow blower operation caution! Failure to obey the following procedures may result in personal injury. • avoid pinch points and be aware of rotating parts when manually turning fan or auger. E) the fan can then be manually turned in a reverse rotation, allowing the foreign object to be ...
20 lift points lifting points are identified by lifting decals where required. Lifting at other points is unsafe and can damage attachment. Do not attach lifting accessories around cylinders or in any way that may damage hoses or hydraulic components. • attach lifting accessories to unit at recommen...
21 maintenance read and understand all safety statements read all safety decals and safety statements in all manuals prior to operating or working on this equipment. Know and obey all osha regulations, local laws, and other professional guidelines for your operation. Know and follow good work practi...
22 maintenance read and understand all safety statements read all safety decals and safety statements in all manuals prior to operating or working on this equipment. Know and obey all osha regulations, local laws, and other professional guidelines for your operation. Know and follow good work practi...
23 problem possible cause possible solution auger will not rotate hoses installed incorrectly switch quick coupler fittings hydraulic valve on skid steer not engaged see skid steer operator's manual for auxiliary operation procedure worn, damaged, insufficient or inadequate pump repair or replace hy...
24 product specifications notice! Exceeding any of the maximum recommended prime mover specifications can result in damage to this product and will void all ffc warranties. Description specifications all models motor kit (a) all models motor kit (c) (d) or (e) all models motor kit (f) (g) or (h) wei...
25 bolt torque specifications note - nylock nuts are utilized when greater resistance to vibrating loose is required, and greater operating temperatures are not a factor. In addition, like lock nuts, nylock nuts have a safety feature that if the bolt does vibrate loose, the nut will remain on the sc...
26 warranty limited warranty except for the excluded products as described below, all new products are warranted to be free from defects in material and/or workmanship during the warranty period, in accordance with and subject to the terms and conditions of this limited warranty. 1. Excluded product...
27 notes.
28 standard flow housing assembly 32 32 25 17 27 33 22 35 12 25 32 32 29 34 27 15 27 33 11 23 5 24 28 1 19 4 30 13 31 32 2 1 26 20 3 14.
29 standard flow housing assembly item part qty description 1. 07-1763 8 washer, flat, 1/2 sae, gr8 2. 07-10126 22 washer, flat, 1 5/8 sae, gr5 3. 13-17276 1 weld, auger, standard (48 inch) 13-51790 1 weld, auger, standard (60 inch) 13-51789 1 weld, auger, standard (72 inch) 13-52905 1 weld, auger, ...
30 standard flow chute assembly 17 18 20 24 5 13 23 6 10 11 14 15 4 21 16 21 21 15 19 25 12 23 1 20 24 22 17 9 7 2 8 3.
31 standard flow chute assembly item part qty description 1. 07-3022 1 screw, hhc, gr8, 1/4-20 x 2 2. 07-3432 4 screw, hhc, gr8, 1/4-20 x 3/4 3. 07-4033 4 nut, hex, nylock, gr8, 1/4-20 4. 13-17292 1 gear cover 5. 13-17294 1 weld, chute 6. 13-17487 4 plate, chute, spacer 7. 13-18453 4 rod, .25 x 9.97...
32 48-60 inch a,c,d,e series standard hydraulic components green wire plug yellow wire plug red wire plug brown wire plug 2 20 2 15 15 4 16 7 10 19 1 1 13 11 14 6 12 8 16 6 3 3 3 3 9 10 5 5 22 7 18 30 28 24 17 33 35 27 31 23 36 33 26 32 29 25 34 21.
33 standard hydraulic components 48-60 inch a,c,d,e series item part qty description 1. 03-1953 2 elbow, 90º, 6mf-10mb 2. 03-2092 2 elbow, 90º, 6mb-6mfs 3. 03-2115 4 elbow, 45º, 6mb-6mf 4. 03-2126 1 elbow, 90º, 10mb-10mf 5. 03-4316 2 hose, .25 x 20, 6ffs-6ffs, 3k 6. 03-4372 2 tee, 10mf-10mf-10ff 7. ...
34 72-84 inch d & e series standard hydraulic components green wire plug yellow wire plug red wire plug brown wire plug 2 20 2 15 15 4 16 14 10 19 1 1 12 18 13 6 11 8 16 6 3 3 3 3 9 5 5 22 7 33 25 32 29 26 36 17 33 21 35 27 31 23 30 28 24 34.
35 standard hydraulic components item part qty description 1. 03-1953 2 elbow, 90º, 6mf-10mb 2. 03-2092 2 elbow, 90º, 6mb-6mfs 3. 03-2115 4 elbow, 45º, 6mb-6mf 4. 03-2126 1 elbow, 90º, 10mb-10mf 5. 03-4316 2 hose, .25 x 20, 6ffs-6ffs, 3k 6. 03-4372 2 tee, 10mf-10mf-10ff 7. 03-5256 1 hose, .5 x 51, 1...
36 standard mounting assembly 10 8 7 3 1 8 4 9 10 2 5 14 11 13 12 6 item part qty description 1. 07-7714 1 screw, hhc, gr5, 5/8-11 x 1 1/2 2. 105840 1 washer, fender, .34 x 1.5 x 10ga 3. Laf6535 1 weld, back plate (contact dealer for correct model) 4. P851105 1 washer, lock, 5/16 5. Rhw1105 1 screw,...
37 notes.
38 high flow housing assembly 34 30 35 37 31 21 2 14 38 6 27 34 20 6 10 27 18 31 37 2 31 37 22 12 36 28 29 19 29 24 36 28 13 11 34 30 35 32 26 17 34 30 35 39 4 3 5 15 40 1 33 41 16 7 single motor.
39 high flow housing assembly item part qty description 1. 07-1177 1 clamp, rubber coat, 1/2 x 3/4 2. 07-1763 8 washer, flat, gr8, 1/2 3. 07-3273 1 washer, lock, split, medium, 5/16 4. 07-3298 1 clamp, rubber coat, 1 1/2 x 3/4 5. 07-3436 1 screw, hhc, gr8, 5/16-18 x 3/4 6. 07-10126 22 washer, flat, ...
40 high flow housing assembly dual motor 12 36 6 6 7 26 19 30 35 2 30 35 21 10 34 27 28 20 34 27 11 8 32 29 33 18 32 29 33 37 4 3 5 13 38 1 31 39 14 9 28 24.
41 high flow housing assembly dual motor item part qty description 1. 07-1177 1 clamp, rubber coat, 1/2 x 3/4 2. 07-1763 8 washer, flat, gr8, 1/2 3. 07-3273 1 washer, lock, split, medium, 5/16 4. 07-3298 1 clamp, rubber coat, 1 1/2 x 3/4 5. 07-3436 1 screw, hhc, gr8, 5/16-18 x 3/4 6. 07-10126 22 was...
42 high flow chute assembly 12 16 5 16 12 11 15 6 13 15 4 8 9 12 16 2 10 1 3 8 15 14 7 17 item part qty description 1. 07-3022 1 screw, hhc, gr8, 1/4-20 x 2 2. Laf6527 1 weld, deflector 3. Laf6551 1 plastic deflector liner 4. Laf6565 1 liner, chute, plastic 5. Laf6566 1 chute rotation pad 6. Laf6568...
43 high flow mounting assembly 3 1 3 2 4 5 4 5 item part qty description 1. Laf6594 1 weld, back plate (contact dealer for correct model) 2. Laf1421 1 gasket, hose hole 3. Rhw1604 6 screw, hhc, gr5, 5/8-11 x 2 4. Rhw5632 6 washer, flat, gr5, 5/8 5. Rhw7607 6 nut, top lock, flange, gr8, .63-11.
44 high flow hydraulic components f series 2 15 2 15 25 23 6 6 12 5 16 12 10 14 7 17 18 10 19 28 24 20 11 1 4 21 26 9 1 8 13 5 5 8 3 5 35 34 38 36 33 30 22 31 33 30 35 22 34 38 27 39 37 29 22 34 38 32.
45 high flow hydraulic components f series item part qty description 1. 03-1945 2 fitting, 12mb-12mfs 2. 03-2092 2 elbow, 90º, 6mb-6mfs 3. 03-2177 1 elbow, 90º, 12mb-12mfs 4. 03-2182 1 elbow, 45º, 12mb-12mfs 5. 03-2291 4 fitting, 6mb-6mfs 6. 03-2564 2 fitting, 6mf-10mb 7. 03-3135 1 tee, 12mb-12mf-12...
46 high flow hydraulic components g series 3 22 26 29 20 24 6 12 5 15 2 14 16 17 10 18 28 25 19 11 7 4 21 29 9 1 8 13 20 39 35 36 36 35 39 39 23 35 34 31 32 23 36 6 5 5 5 12 37 34 31 23 35 39 27 40 33 38 30 22 3.
47 high flow hydraulic components g series item part qty description 1. 03-1945 1 fitting, 12mb-12mfs 2. 03-1950 1 tee, 12mf-12mf-12mb 3. 03-2092 2 elbow, 90º, 6mb-6mfs 4. 03-2182 1 elbow, 45º, 12mb-12mfs 5. 03-2291 4 fitting, 6mb-6mfs 6. 03-2564 2 fitting, 6mf-10mb 7. 03-3135 2 tee, 12mb-12mf-12mf ...
48 high flow hydraulic components h series 2 23 2 23 26 27 20 25 5 12 4 16 13 15 3 17 18 10 22 29 34 11 11 6 3 21 27 8 1 7 9 13 1 8 14 19 41 37 38 41 37 24 39 36 31 41 37 38 39 36 41 31 24 37 24 24 33 32 38 37 24 41 35 28 42 40 30 5 4 4 12 4 24 19 21 11.
49 high flow hydraulic components h series item part qty description 1. 03-1945 2 fitting, 12mb-12mfs 2. 03-2092 2 elbow, 90º, 6mb-6mfs 3. 03-2182 2 elbow, 45º, 12mb-12mfs 4. 03-2291 4 fitting, 6mb-6mfs 5. 03-2564 2 fitting, 6mf-10mb 6. 03-3135 1 tee, 12mb-12mf-12mf 7. 03-6343 1 hose, .75 x 80, 12ff...