1. DL manuals
  2. Fiat
  3. Offroad Vehicle
  4. 2016 500L Uconnect 6.5
  5. Owner's Manual

Fiat 2016 500L Uconnect 6.5 Owner's Manual

Other manuals for 2016 500L Uconnect 6.5: Owner's Manual Supplement, User Manual

Summary of 2016 500L Uconnect 6.5

  • Page 1

    O w n e r ’ s m a n u a l 2 0 1 6 fiat ® 500l.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .5 䡵 warnings and cautions . . . . . . . . . . . . . .7 䡵 vehicle identification number . . . . . . . .7 䡵 vehicle modifications/alterations . . . .8 1.

  • Page 6

    Introduction congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engineering spe...

  • Page 7

    How to use this manual consult the table of contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index ...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped vin location 8 introduction.

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .11 ▫ ignition switch . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key. . . . . . . . . . . . . . . .13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 䡵 sen...

  • Page 12

    䡵 door locks . . . . . . . . . . . . . . . . . . . . . . . . .22 ▫ doors lock with one or more doors open . . .24 ▫ auto — relocking (only for rear doors) . . . . .24 ▫ child-protection door lock system — rear doors . . . . . . . . . . . . . . . . . . . . . . . . . .25 ▫ to engage or disengage the c...

  • Page 13

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key simply push the mechanical key release button. Note: the authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These number...

  • Page 14

    Ignition switch the ignition switch can be turned to three different positions: • stop: engine off, key can be removed. Some electrical devices (e.G. Sound system, central door locking sys- tem, etc.) can operate; note: in vehicles equipped with automatic transmis- sions, the transmission must be in...

  • Page 15

    Warning! • before exiting a vehicle, shift the automatic trans- mission into park or the manual transmission into reverse, apply the parking brake, turn the vehicle off, remove the key fob from the ignition and lock your vehicle. • never leave children alone in a vehicle, or with access to an unlock...

  • Page 16

    Key-in-ignition reminder opening the driver’s door when the key is in the ignition and the ignition switch position is off/lock sounds a signal to remove the key. Sentry key the sentry key immobilizer system prevents unauthor- ized vehicle operation by disabling the engine. The system does not need ...

  • Page 17

    Replacement keys note: only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a sentry key has been programmed to a vehicle, it cannot be programmed to any other vehicle. Note: when having the sentry key immobilizer sys- tem serviced, bring all vehicle ...

  • Page 18

    To arm the system 1. Remove the key from the ignition switch and get out of the vehicle. 2. Lock the door using either the central lock/unlock switch or the remote keyless entry (rke) transmitter and close all doors. 3. The horn will sound and the vehicle security light in the instrument cluster wil...

  • Page 19

    The vehicle security alarm is designed to protect your vehicle; however, you can create conditions where the vehicle security alarm will arm unexpectedly. If you remain in the vehicle and lock the doors with the rke transmitter, once the vehicle security alarm is armed, when you pull the door handle...

  • Page 20

    Activating the safe lock device the safe lock device is enabled on all the doors by quickly double-pushing the lock button on the rke transmitter. The direction indicators flash three times and the led above the button flashes to indicate that the safe lock device has been activated. If one or more ...

  • Page 21

    Note: the line of transmission must not be blocked with metal objects. To unlock the doors and liftgate push and release the unlock button on the rke transmitter once to unlock the driver’s door or twice, within five seconds, to unlock all doors and the liftgate. The turn signal lights will flash to...

  • Page 22

    Request for additional remote controls the system can recognize up to 8 remote controls. Should a new remote control be necessary, go to an authorized dealer, taking an id document and the car ownership documents. Replacing the battery in the key with remote control key fob components 20 things to k...

  • Page 23

    To replace the battery, proceed as follows: • push button a to open the metal insert b; • turn the screw c to unlock using a small screwdriver; • take out the battery case d and replace the battery e making sure that polarities are correct; • refit the battery case d inside the key and lock it turni...

  • Page 24

    Door locks push the central lock/unlock button located on the instrument panel, in the switch bank below the radio. The button has an led that indicates whether the doors are locked or unlocked. • led on: doors locked. Pushing the central lock/ unlock button once will unlock all doors. The led will ...

  • Page 25

    Note: with central locking active (led on), opening one of the front doors, it is possible to perform a central unlocking (led off). With central locking active (led on), in order to open one of the rear passenger doors, it is necessary pulling the internal door handle twice. With one of the rear do...

  • Page 26

    Warning! (continued) warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the key fob in or near the vehicle, or in a location accessible to children. A child could operate power windows, other controls, or move the vehicle. Caution! An unlocked vehicle is an invit...

  • Page 27

    Child-protection door lock system — rear doors to provide a safer environment for small children riding in the rear seats, the rear doors are equipped with child-protection door lock system. To engage or disengage the child-protection door lock system 1. Open the rear door. 2. Insert the tip of the ...

  • Page 28

    Power windows power window switches the power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door, which operate the front passenger win- dow and a single switch on each rear door that operates the rear passenger door window. The window c...

  • Page 29

    Note: the power window switches will remain active for up to three minutes after the ignition switch is cycled to the off position. Opening either front door will cancel this feature. Warning! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave...

  • Page 30

    Note: • if the window runs into any obstacle during auto- closure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window. • any impact due to rough road conditions may trigger the auto-reverse function unexpectedly during auto- closu...

  • Page 31

    Open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Liftgate to unlock the liftgate, use the remote keyless entry (rke) transmitter or activate th...

  • Page 32

    1. Remove the rear headrests and fold down the seats completely 2. Take the screwdriver from the tool box supplied 3. With the screwdriver remove the tab of yellow color (a) 4. Introduce the screwdriver into the seat b in order to trigger the release tab of the trunk (follow the direction arrow to o...

  • Page 33

    Occupant restraint systems some of the most important safety features in your vehicle are the restraint systems: • seat belt systems • supplemental restraint systems (srs) air bags • child restraints important safety precautions please pay close attention to the information in this section. It tells...

  • Page 34

    6. All occupants should always wear their lap and shoulder belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the advanced front air bags room to inflate. 8. Do not lean against the door or window. If your vehicle has side air bags, and deployme...

  • Page 35

    Ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Enhanced seat belt use reminder system (beltalert) — if equipped driver and passenger beltalert beltalert is a feature intended to remind the driver and outboard f...

  • Page 36

    Sequence may repeat based on vehicle speed until the driver and occupied outboard front seat passenger seat belts are buckled. The driver should instruct all occu- pants to buckle their seat belts. Change of status if the driver or outboard front seat passenger (if equipped with outboard front passe...

  • Page 37

    Warning! • relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belt even though you have air bags. • in a collision, you and your p...

  • Page 38

    Warning! (continued) • a lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap part of your seat belt as low as possible and keep it snug. • a twisted seat belt may not pro...

  • Page 39

    Warning! (continued) • a frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be re- placed immediately. Do not disassemble or modify the seat belt system. Sea...

  • Page 40

    4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding...

  • Page 41

    Position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 1...

  • Page 42

    Position the lap belt snug and low below the abdomen and across the strong bones of the hips. Place the shoulder belt across the chest and away from the neck. Never place the shoulder belt behind the back or under the arm . Seat belt pretensioner the front seat belt system is equipped with pretensio...

  • Page 43

    Restraints” section of this manual. The table below defines the type of feature for each seating position. • alr = switchable automatic locking retractor (alr) if the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough...

  • Page 44

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 45

    Warning! (continued) only used to install rear-facing or forward-facing child restraints that have a harness for restraining the child. Supplemental restraint system (srs) air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint contro...

  • Page 46

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 47

    Output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front impact sensors or other system components. The first stage inflator is triggered immediately during an impact that requires air bag deployme...

  • Page 48

    Warning! (continued) some collisions, air bags won’t deploy at all. Al- ways wear your seat belts even though you have air bags. Advanced front air bag operation advanced front air bags are designed to provide addi- tional protection by supplementing the seat belts. Ad- vanced front air bags are not...

  • Page 49

    Knee impact bolsters the knee impact bolsters help protect the knees of the driver and front passenger, and position the front occu- pants for improved interaction with the advanced front air bags. Warning! • do not drill, cut, or tamper with the knee impact bolsters in any way. • do not mount any a...

  • Page 50

    Supplemental side air bags your vehicle is equipped with two types of side air bags: 1. Supplemental seat-mounted side air bags (sabs) are located in the outboard side of the front seats. The sabs are marked with a “srs airbag” or “airbag” label sewn into the outboard side of the seats. The sabs may...

  • Page 51

    Deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not seated properly, or if items are positioned in the area where the sab inflates. Children are at an even greater...

  • Page 52

    The sabics deploy downward, covering the side win- dows. An inflating sabic pushes the outside edge of the trim out of the way and covers the window. The sabics inflate with enough force to injure occupants if they are not belted and seated properly, or if items are positioned in the area where the ...

  • Page 53

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts and certain rollover events. The occupant restraint controller (“orc”) de- termines whether the deployment of the side air bags in a particular side impact or rollover event is appropriate, based on the severity a...

  • Page 54

    Warning! (continued) properly. In some collisions, side air bags won’t deploy at all. Always wear your seat belt even though you have side air bags. Note: air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. Side impacts in side impacts, the side impa...

  • Page 55

    Air bags is appropriate, the rollover sensing system will also deploy the seat belt pretensioners on both sides of the vehicle. If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions....

  • Page 56

    Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the seat belt retractor assemblies replaced by an authorized dealer imme- diately. Also, have the occupant restraint controller system serviced as well. Not...

  • Page 57

    Enhanced accident response system reset procedure after the event occurs, when the system is active, a message regarding fuel cutoff is displayed. Turn the ignition switch from ignition avv/start or mar/ acc/on/run to ignition stop/off/lock. Care- fully check the vehicle for fuel leaks in the engine...

  • Page 58

    Customer action customer will see 6. Turn left turn signal switch on. Left turn light is on solid. Right turn light is on solid. 7. Turn left turn signal switch off. (turn signal switch must be placed in neutral state). Left turn light is off. Right turn light is off. 8. Turn ignition off. 9. Turn h...

  • Page 59

    The mar/acc/on/run position. After the self-check, the air bag warning light will turn off. If the orc detects a malfunction in any part of the system, it turns on the air bag warning light, either momentarily or continuously. A single chime will sound to alert you if the light comes on again after ...

  • Page 60

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 61

    Assist in understanding how a vehicle’s systems per- formed. The edr is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The edr in this vehicle is designed to record such data as: • how various systems in your vehicle w...

  • Page 62

    Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash st...

  • Page 63

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and tod- dlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrie...

  • Page 64

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 65

    Remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat bel...

  • Page 66

    Children too large for booster seats children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat. Use this simple 5-step test to decide whether ...

  • Page 67

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 68

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 69

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 2 things to know before starting your vehicle 67.

  • Page 70

    What is the weight limit (child’s weight + weight of the child re- straint) for using the latch an- chorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and ...

  • Page 71

    Can two child restraints be at- tached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchor- ages, use the seat belt to install a child seat in the center position next to a child...

  • Page 72

    Locating latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the ...

  • Page 73

    Locating the upper tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat, near the floor. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to...

  • Page 74

    Tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center seat latch: warning! • do not install a child restraint in the center posi- tion using the latch system. This position is not ...

  • Page 75

    Restraint to get a better fit. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move it to its rear-most position to make room for the child seat. You may also move the front seat forward to allow more room for the child seat. 3. Attach the lower hooks or connectors...

  • Page 76

    Seat belts are not toys and that they should not play with them. Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when install...

  • Page 77

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor • top tether anchorage symbol 2 things to know before starting your vehicle 75.

  • Page 78

    What is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for- ward facing child restrai...

  • Page 79

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 80

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 81

    Tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available. 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints...

  • Page 82

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 83

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tip...

  • Page 84

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 85

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 86

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor cover- ings in the vehicle that cannot...

  • Page 87

    Lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel bolts for tightness. Check the tires (including spare) for proper cold inflation pressure. Lights have someone observe the operation of brake lights and exterior lig...

  • Page 89: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 ▫ inside day/night mirror . . . . . . . . . . . . . . . .90 ▫ automatic dimming mirror — if equipped . . .91 ▫ conversation mirror — if equipped . . . . . . . . .92 ▫ power mirro...

  • Page 90

    ▫ turn signals . . . . . . . . . . . . . . . . . . . . . . . . .112 ▫ lane change assist . . . . . . . . . . . . . . . . . . . .112 ▫ follow me home/headlight delay . . . . . . . . .112 ▫ front fog lights — if equipped . . . . . . . . . . .113 ▫ interior lights . . . . . . . . . . . . . . . . . . . ...

  • Page 91

    ▫ programming a rolling code . . . . . . . . . . . . .134 ▫ programming a non-rolling code . . . . . . . . .136 ▫ canadian/gate operator programming . . . . . .138 ▫ using homelink . . . . . . . . . . . . . . . . . . . . . .139 ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . .140 ▫ ...

  • Page 92

    Mirrors inside day/night mirror a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjus...

  • Page 93

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activat...

  • Page 94

    Conversation mirror — if equipped there is a conversation mirror located at the top of the overhead console. To gain access to the conversation mirror, pull downward on the mirror to the open position. Power mirrors the power mirror controls are located on the driver’s door trim panel. To adjust a m...

  • Page 95

    Move. When you are finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror. Folding mirrors the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The mirror has three detent positions: full forwar...

  • Page 96

    Sun visor “slide-on-rod” feature the sun visor “slide-on-rod” feature allows for addi- tional flexibility in positioning the visor to block out the sun. To use the “slide-on-rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “slide-on-rod” until the sun visor is ...

  • Page 97

    Seats front seats forward/rearward adjustment the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired position is reached. Then, using body pressure, move forward and...

  • Page 98

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 99

    Recliner adjustment the recline lever is located on the outboard side of the seat. To recline the seat, lean forward slightly, lift the lever, lean back to the desired position and release the lever. To return the seatback to its normal upright posi- tion, lean forward and lift the lever. Release th...

  • Page 100

    Warning! (continued) adjusted properly and you could be injured. Adjust the seat only while the vehicle is parked. • do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even f...

  • Page 101

    Note: once a heat setting is selected, heat will be felt within two to five minutes. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care...

  • Page 102

    Rear seats rear seats forward/rearward adjustment the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired position is reached. Then, using body pressure, move forward...

  • Page 103

    Reclining rear seats the recliner handle is located on the outside of the seat cushion. To adjust the seatback, lift upward on the handle, lean back on the seatback and when you reach the desired position, release the handle. Warning! Do not ride with the seatback reclined so that the shoulder belt ...

  • Page 104

    1. Lift the seatback release lever located on the upper outboard side of the seat. 2. Fold the seatback forward. Seatback release lever seatback folded 102 understanding the features of your vehicle.

  • Page 105

    3. Locate the seatback recline lever on the outboard side of the seat and lift upward on the lever. 4. Slowly flip the entire seat forward. 5. Slowly flip the entire seat rearward and firmly lock the seat into position. 6. Raise the rear seatback and firmly lock the seatback into position. Seatback ...

  • Page 106

    Rear armrest — if equipped to use the armrest, lower it downward. Folding rear seat armrest armrest cupholder 104 understanding the features of your vehicle.

  • Page 107

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear- impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be...

  • Page 108

    The reactive head restraints will automatically return to their normal position following a rear impact. If the reactive head restraints do not return to their normal position, see your authorized dealership immediately. Warning! • a loose head restraint thrown forward in a colli- sion or hard stop ...

  • Page 109

    Rear head restraints the rear seats are equipped with adjustable head re- straints, the outboard head restraints have two comfort positions, while the central head restraint have to use in the raised position. When there are no occupants in the center seat, the head restraint can be lowered for maxi...

  • Page 110

    For proper routing of a child seat tether, refer to “occupant restraints” in “things to know before start- ing your vehicle.” warning! All the head restraints must be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the ve...

  • Page 111

    2. Move to the outside of the vehicle and push the red safety catch lever to the left and raise the hood. The safety catch lever is located under the center front edge of the hood. Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately ...

  • Page 112

    Caution! (continued) secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. ...

  • Page 113

    Headlights rotate the end of the multifunction lever up- ward to the first detent for headlight operation. Note: when the headlights are turned on, the daytime running lights will be deactivated. Daytime running lights — if equipped to activate the daytime running lights (drl), rotate the end of the...

  • Page 114

    Flash-to-pass you can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released. Parking lights to turn on the parking lights, remove the key or turn the igniti...

  • Page 115

    Deactivation pull the multifunction lever toward the steering wheel and hold it for more than two seconds. Front fog lights — if equipped the fog light switch is located on the center stack of the instrument panel, just below the radio. Push the switch once to turn the front fog lights on. Push the ...

  • Page 116

    Push the switch to the off/left position from its center position and the lights are always off. Leave the switch in the center position, and the lights are turned on and off when the doors are opened or closed. Off/left position center position 114 understanding the features of your vehicle.

  • Page 117

    The switches on the left and right sides of the overhead console controls the map or reading function of the lights. Push the switch to the right to turn on the right light and push the switch to the left to turn on the left light. Caution! Before getting out of the vehicle be sure that the switch i...

  • Page 118

    • when the doors are locked with the key fob the lights will turn off. Interior light timing (on/right position) • when all doors are closed a 15 minute timer is activated. Note: the timer is deactivated when the key is moved into the on/run position. Windshield wipers and washers the windshield wip...

  • Page 119

    Windshield wiper off this is the normal position of the wiper lever. Intermittent speed rotate the end of the lever upward to the first detent. The wipers will operate at intermittent speed. Low speed rotate the end of the lever upward to the second detent. The wipers will operate at low speed. High...

  • Page 120

    Front windshield washer operation pull the windshield wiper/washer lever toward the steering wheel to activate the washers. The wipers will activate automatically for three cycles after the lever is released. Caution! • turn the windshield wipers off when driving through an automatic car wash. Damag...

  • Page 121

    Rear window wiper/washer activation rotate the windshield wiper lever center ring upwards to operate the rear window wiper as follows: • in intermittent mode when the front windshield wiper is not operating. • in synchronous mode (at half the speed of the front window wiper) when the front windshiel...

  • Page 122

    Window wiper as well. Releasing the windshield wiper lever will activate the smart washing function, as de- scribed for the windscreen wiper. Deactivation the function stops when the windshield wiper lever is released. Tilt/telescoping steering column this feature allows you to tilt the steering col...

  • Page 123

    To unlock the steering column, pull the control handle down. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the...

  • Page 124

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 125

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 126

    U.S. Speed (mph) • pushing the res (+) button once will result in a 1 mph increase in set speed. Each subsequent tap of the button results in an increase of 1 mph. • if the button is continually pushed, the set speed will continue to increase until the button is released, then the new set speed will...

  • Page 127

    Metric speed (km/h) • pushing the set (-) button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a decrease of 1 km/h. • if the button is continually pushed, the set speed will continue to decrease until the button is released, then the new set speed ...

  • Page 128

    Rear park assist is automatically activated when the transmission is placed into reverse. As the distance from an obstacle behind the vehicle decreases, the au- dible alert becomes more frequent. Interaction with trailer towing the rear park assist system is automatically deactivated when a trailer ...

  • Page 129

    Audible and visual signals supplied by the rear park assist system signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loudspeaker) • sound pulses emitted at a rate that increases as the distance decreases. • emits continuous...

  • Page 130

    While audible signals are emitted, the audio system is not muted. The audible signal is turned off immediately if the distance increases. The tone cycle remains constant if the distance measured by the inner sensors is constant. If this condition occurs for the external sensors, the signal is turned...

  • Page 131

    Cm) from the sensors. Do not scratch or poke the sensors. Otherwise, you could damage the sensors. Park assist system usage precautions note: • ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the rear park ass...

  • Page 132

    Caution! (continued) • the vehicle must be driven slowly when using rear park assist in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using rear park assist. Warning! • drivers must be careful when backing up even wh...

  • Page 133

    Parkview rear back up camera — if equipped your vehicle may be equipped with the parkview rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed in the touchscreen display along ...

  • Page 134

    The following table shows the approximate distances for each zone: zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm) yellow 1 ft - 3 ft (30 cm - 1 m) green 3 ft or greater (1 m or greater) warning! Drivers must be careful when backing up even when using the parkview rear back up came...

  • Page 135

    Note: if snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Garage door opener — if equipped homelink replaces up to three remote controls (hand- held transmitters) that operate devices such as ga...

  • Page 136

    Before you begin programming homelink be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the de...

  • Page 137

    1. Place the ignition in the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink button you wish to program while keeping the homelink indicator light in view. 3. Push and hold the homelink button you want to program while you push and hold the hand-h...

  • Page 138

    Firmly push and release the “learn” or “train- ing” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the learn/train mode. Note: you have 30 seconds in which to initiate the next step after the learn button has been pushed. 6. Retu...

  • Page 139

    2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink button you wish to program while keeping the homelink indicator light in view. 3. Push and hold the homelink button you want to program while you push and hold the hand-held transmitter button. 4. Continue to hold bo...

  • Page 140

    Canadian/gate operator programming for programming transmitters in canada/united states that require the transmitter signals to “time-out” after several seconds of transmission. Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission ...

  • Page 141

    Note: • if the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the homelink button is pushed. • to program the two remaining homelink buttons, repeat each step for each remaining button. Do not erase the channels. If you unplugged the ga...

  • Page 142

    Security it is advised to erase all channels before you sell or turn in your vehicle. To do this, push and hold the two outside buttons for 20 seconds until the red indicator flashes. Note that all channels will be erased. Individual channels cannot be erased. The homelink universal transceiver is d...

  • Page 143

    Warning! (continued) required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features. Call toll-free 1-800-355-3515 or, on the internet at homelink.Com for safety information or assistance. Gene...

  • Page 144

    The power sunroof and power sun blind switches are located in the overhead console. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle or in a location accessible to children. Occupants, particularly unattended ch...

  • Page 145

    To open • pull the power sunroof switch for approximately one second and the sunroof will stop at the vented posi- tion. Pull the power sunroof switch a second time for approximately one second and release, the sunroof will open fully, then stop automatically. This is called “express open”. Note: du...

  • Page 146

    Note: during the automatic opening and closing stages, if the power sun blind switch is pulled again it will stop the blind movement. Power outlets passenger compartment power socket the power outlet is located on the central tunnel, in front of the shift lever, between the two cup holders. It only ...

  • Page 147

    Cigar lighter — if equipped this is located on the central tunnel, next to the parking brake lever. To activate the cigar lighter, push and release the knob. After a few seconds the knob automatically returns to its initial position, and the cigar lighter is ready for use. Cigar lighter — if equippe...

  • Page 148

    Warning! When the cigar lighter is in use it becomes very hot. To avoid serious injury, handle the cigar lighter with care. Always check that the cigar lighter has turned off. Note: • always check that the cigar lighter is switched off. • do not connect devices with power higher than 180 w to the so...

  • Page 149

    Storage glove compartment your vehicle is equipped with a upper and lower glove compartment which is located on the right side of the instrument panel. Push the latch button upward on the upper glove compartment door to open it. Pull outward on the lower glove compartment latch to open the lower glo...

  • Page 150

    Front center armrest storage — if equipped the front center armrest contains a storage compartment. To open the storage compartment push in the upper release latch on the front of the armrest. Lift upward on the armrest to gain access to the storage area. The front center armrest can also be lifted ...

  • Page 151

    Rear cargo storage features the car features a load platform which can be adjusted to three different heights, permitting modular luggage com- partment volume: • position 1 (platform completely lowered) permits maximum luggage compartment capacity. • position 2 (platform at threshold level) permits ...

  • Page 152

    The area below the luggage compartment. In this position also the plan guarantees the correct locking of any objects present inside the cargo area, avoiding that they move in the event of sudden braking. Caution! The dimension of the cargo floor permit a maximum capacity of a distributed weight of 1...

  • Page 153

    2. Place the desired objects in compartment. Load platform 1 — handle 2 — platform load compartment 3 understanding the features of your vehicle 151.

  • Page 154

    3. Then reposition the platform correctly in the housings on the side panels and rear crossmember. Note: movements of the load platform must take place in a central position relative to the luggage compartment. Moving the load platform to move the load platform from lower to upper position, proceed ...

  • Page 155

    2. Position the platform correctly on housing on the side panels. Load platform 1 — handle 2 — platform raised position 1 — front housing locations 2 — rear housing locations 3 understanding the features of your vehicle 153.

  • Page 156

    Securing your load there are two tie downs inside the luggage compartment for attaching cables which can secure the load carried. A further two tie downs located on the rear crossmember. Two hooks are also available on the side panels to fix loads which are not excessively heavy (e.G. Bags). To use ...

  • Page 157

    Caution! The maximum load admitted per each bag hook is 22 lbs (10 kg). Storage compartments there are two storage compartments located on the rear side panels. Storage compartment 3 understanding the features of your vehicle 155.

  • Page 158

    Rear window features rear window defroster the rear window defroster button is located with the climate controls on the instrument panel. Push this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster ...

  • Page 159

    Roof luggage rack-if equipped the crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 110 lbs (50 kg), and should be uniformly distributed over the luggage rack crossbars. Their are two attachment points inside the door jambs th...

  • Page 160

    Warning! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the roof rack cautions when carrying cargo on your roof rack. Rear window features rear window de...

  • Page 161: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .162 䡵 instrument cluster . . . . . . . . . . . . . . . . .163 䡵 warning and indicator lights . . . . . . .165 ▫ red telltale indicator lights . . . . . . . . . . . . . .166 ▫ yellow telltale indicator lights ...

  • Page 162

    ▫ values displayed . . . . . . . . . . . . . . . . . . . . . .193 ▫ personal settings (customer-programmable features). . . . . . . . . . . . . . . . . . . . . . . . . . . .194 䡵 cybersecurity. . . . . . . . . . . . . . . . . . . . . . .208 䡵 uconnect settings . . . . . . . . . . . . . . . . . .210 ...

  • Page 163

    ▫ navigation (6.5a/6.5an) . . . . . . . . . . . . . . . .257 ▫ voice text reply . . . . . . . . . . . . . . . . . . . . . .258 ▫ general information . . . . . . . . . . . . . . . . . . .259 ▫ additional information . . . . . . . . . . . . . . . . .260 4 understanding your instrument panel 161.

  • Page 164

    Instrument panel features 1 — side vent 7 — fixed upper air vent 13 — climate controls 2 — steering wheel audio control — lo- cated on back side of steering wheel 8 — passenger advanced front air bag 14 — usb port/sd card/aux socket 3 — multifunction lever – light control 9 — upper glove compartment...

  • Page 165

    Instrument cluster evic instrument cluster 4 understanding your instrument panel 163.

  • Page 166

    1. Speedometer • indicates vehicle speed 2. Fuel gauge • the pointer shows the level of fuel in the fuel tank when the ignition switch is in the on/run position 3. Temperature gauge • the temperature gauge shows engine coolant tem- perature. Any reading within the normal range indi- cates that the e...

  • Page 167

    4. Tachometer • indicates the engine speed in revolutions per minute (rpm x 1000). 5. Electronic vehicle information center (evic) • when the appropriate conditions exist, this display shows the electronic vehicle information center (evic) messages. Refer to “electronic vehicle infor- mation center”...

  • Page 168

    Red telltale indicator lights brake warning light red telltale light what it means united states canada brake warning light this light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is ap...

  • Page 169

    The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the brake warning light, which will turn on when the brake fluid level in the master cylinder has dropped below a...

  • Page 170

    The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the parking brake is applied. It does not show the degree of brake application. Engine temperature warning light red warning light what it means engine te...

  • Page 171

    Seat belt reminder warning light red telltale light what it means seat belt reminder warning light when the ignition switch is first turned to on/run, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound....

  • Page 172

    Air bag warning light red telltale light what it means air bag warning light this light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspe...

  • Page 173

    Oil pressure warning light red telltale light what it means oil pressure warning light this light indicates low engine oil pressure. If the light turns on while driving, stop the ve- hicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the ve...

  • Page 174

    Electronic throttle control (etc) warning light red telltale light what it means electronic throttle control (etc) warning light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected while the engine is running, the light will either stay on ...

  • Page 175

    Anti-lock brake (abs) indicator light yellow telltale light what it means anti-lock brake (abs) indicator light after the ignition is turned on, the anti-lock brake system (abs) light illuminates to indi- cate function check at vehicle startup. If the light remains on after startup or comes on and s...

  • Page 176

    Yellow telltale indicator lights electronic stability control (esc) activation / malfunction indicator light yellow telltale light what it means electronic stability control (esc) indicator light the esc activation/malfunction indicator light in the instrument cluster will come on for four seconds w...

  • Page 177

    Electronic stability control (esc) off indicator light yellow telltale light what it means electronic stability control (esc) off indicator light this light indicates the electronic stability control (esc) is off. Rear defrost light yellow telltale light what it means rear defrost light this indicat...

  • Page 178

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 179

    Low fuel indicator light yellow telltale light what it means low fuel indicator light when the fuel level reaches approximately 3.0 gal (11.0 l) this light will turn on, and remain on until fuel is added. Passenger air bag indicator light yellow telltale light what it means passenger air bag indicat...

  • Page 180

    Engine check/malfunction indicator light (mil) yellow telltale light what it means engine check/malfunction indicator light (mil) the engine check/malfunction indicator light (mil) is a part of an onboard diagnostic system called obd ii that monitors engine and automatic transmission control systems...

  • Page 181

    Caution! Prolonged driving with the malfunction indicator light (mil) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the mil is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. Warni...

  • Page 182

    Tire pressure monitoring indicator light yellow telltale light what it means tire pressure monitoring indicator light the warning light switches on and a message is displayed to indicate that the tire pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these ...

  • Page 183

    One or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and ...

  • Page 184

    Caution! (continued) warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket...

  • Page 185

    Glow plug light — if equipped yellow telltale light what it means glow plug light — if equipped this vehicle will inhibit engine cranking when the ambient temperature is less than –22° f (–30° c) and the oil temperature sensor reading indicates an engine block heater has not been used. The glow plug...

  • Page 186

    Green telltale indicator lights turn signal indicator lights green tell- tale light what it means turn signal indicator lights the instrument cluster arrow will flash independently for the left or right turn signal as se- lected, as well as the exterior turn signal lamp(s) (front and rear) as select...

  • Page 187

    Park/headlight on indicator light green telltale light what it means park/headlight on indicator light this indicator will illuminate when the park lights or headlights are turned on. White telltale indicator light electronic speed control set light white telltale light what it means electronic spee...

  • Page 188

    Blue telltale indicator light high beam indicator light blue telltale light what it means high beam indicator light this indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch...

  • Page 189

    Evic screen the evic will display the following: • time • date or trip distance display in miles or kilometers • outside temperature • gear indicator • odometer (display of distance travelled in miles/ kilometers) • car status indication (e.G. Doors open, possible ice on road, service, etc.) evic co...

  • Page 190

    Electronic vehicle information center (evic) setup menu the menu comprises a series of functions arranged in a cycle. The menu includes the following functions: note: some of the menu items could be managed by uconnect (if equipped). In that case, some of these are not present in evic but in uconnec...

  • Page 191

    • tire reset • city brake control • selecting an option of the main menu without submenu briefly push and release the menu button to select the main menu option to set. Push and release the up or down button (by single pushes) to select the new setting. Briefly push and release the menu button to st...

  • Page 192

    Change engine oil indicator system your vehicle is equipped with an engine oil change indicator system. The “oil change required” message will flash in the evic display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil ch...

  • Page 193

    • a short button push displays the different values. • a long button push resets the system and then starts a new trip. New trip to reset: • push and hold the trip button to reset the system manually. • when the “trip distance” reaches 99999.9 miles or kilometers or when the “travel time” reaches 99...

  • Page 194

    Start of trip procedure with the ignition on, push and hold the trip button for over one second to reset. Exit trip to exit the trip function, wait until all the values have been displayed or hold the menu button for longer than one second. Briefly push and release the menu button to go back to the ...

  • Page 195

    Values displayed range this indicates the distance which may be traveled with the fuel remaining in the tank, assuming that driving conditions will not change. The message “----” will appear on the display in the following cases: • distance less than 30 miles (or 50 km). • the vehicle is parked for ...

  • Page 196

    Personal settings (customer-programmable features) dimmer note: the brightness of ipc will change automatically only if the external light has changed: external light on= night mode, external light off= day mode. In both case (day or night) is possible to adjust the display brightness as described i...

  • Page 197

    Note: selection is possible between 20 – 125 mph or (32 – 201 km/h), depending on the selected unit. The setting will increase/decrease by five units each time the up/ down button is pushed. Push and hold the up/down button to increase/decrease the setting rapidly. Save the setting by briefly pushin...

  • Page 198

    Proceed as follows to set: • push menu button briefly. The level set previously flashes on the display; • push the up or down button to make the adjust- ment; • push the menu button briefly to return to the menu screen or hold the button down to return to the standard screen without storing. Corneri...

  • Page 199

    Trip b data (trip b on) through this option, it is possible to activate (on) or deactivate (off) the trip b (partial trip) display. For further information, see “trip computer.” for activation / deactivation, proceed as follows: 1. Briefly push and release the menu button. 2. Push and release the up...

  • Page 200

    7. Push and release the up or down button for setting. Note: • the setting will increase or decrease by one unit each time the up or down button is pushed. Push and hold the button to increase/decrease the setting rapidly. Save the setting by briefly pushing the button when you approach the required...

  • Page 201

    3. Briefly push and release the menu button and “month” will flash on the display. 4. Push and release the up or down button for setting. 5. Briefly push and release the menu button and “day” will flash on the display. 6. Push and release the up or down button for setting. Note: the setting will inc...

  • Page 202

    • briefly push the menu button to go back to the menu screen or hold the button down to go back to the standard screen without saving. When the key is turned to mar/on and the initial check stage is over, the display will show the information selected via the ⬙first page⬙ menu function. Audio repeti...

  • Page 203

    Autoclose with this function active, the doors will automatically lock at when the vehicle’s speed exceeds 15 mph (24 km/h). To change the setting proceed as follows: 1. Briefly push and release the menu button. Push the up or down button to highlight autoclose. Push and release the menu button to e...

  • Page 204

    4. When accessing the “distance” submenu, briefly push and release the menu button. Either “mi” or “km” will appear on the display (according to the previous setting). 5. Push and release the up or down button for setting. 6. Briefly push and release the menu button to return to the sub-menu. 7. Whe...

  • Page 205

    Language (selecting the language) the messages can be displayed in the following lan- guages: italian, english, turkce, nederlands, spanish, french, dutch, polish, brasilian. To set the required language, proceed as follows: 1. Briefly push and release the menu button. Push and release the up or dow...

  • Page 206

    Seat belt buzzer (buzzer activation for beltalert indication) this function will only be displayed after a fiat group automobiles dealership has deactivated the beltalert system. Refer to “enhanced seat belt use reminder system beltalert” in “occupant restraints” for further information. To reactiva...

  • Page 207

    Note: the “scheduled servicing plan” includes car maintenance at fixed intervals. This is displayed auto- matically, with ignition key at mar/on, 2000 km (or equivalent value in miles) before servicing or, where provided, 30 days before servicing. It is also displayed each time the key is turned to ...

  • Page 208

    • push the menu button briefly; a message confirming the selection is displayed and you return to the menu screen; hold down the button to return to the standard screen without storing. Daytime running lamps (drl) this function may be used to activate / deactivate the daytime running lamps. Proceed ...

  • Page 209

    2. Push and release the up or down button for setting. 3. Briefly push and release the menu button to go back to the menu screen, or push and hold the button (approximately one second) to go back to the main screen without storing the settings. City brake control (collision mitigation) this function...

  • Page 210

    • briefly push the menu button. The display will show ⬙confirm.⬙ • push the up or down buttons to select ⬙yes⬙ to reset or ⬙no⬙ to exit the page. • hold the menu button down again to return to the standard screen or to the main menu. Exit menu this function closes the initial menu screen. Briefly pu...

  • Page 211

    The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent version of vehicle software (such as uconnect software) is installed. Warning! • it is not possible to know or to predict all of the possible outcomes if your vehicle’s systems are breached....

  • Page 212

    Privacy of any wireless and wired communications can- not be assured. Third parties may unlawfully intercept information and private communications without your consent. For further information, refer to “onboard di- agnostic system (obd ii) cybersecurity” in “maintaining your vehicle”. Uconnect set...

  • Page 213

    Customer programmable features — uconnect 6.5n settings press the settings button to display the menu setting screen. In this mode the uconnect system allows you to access programmable features that may be equipped such as display, clock, safety & driving assistance, lights, doors & locks, auto-on c...

  • Page 214

    Note: when day or night is selected for the display mode, the usage of the parade mode feature will cause the radio to activate the display brightness day control even though the headlights are on. • display brightness with headlights on this feature will allow you to select the brightness with the ...

  • Page 215

    Designated turn within a programmed route. To make your selection, press the “navigation turn-by-turn in cluster” button on the touchscreen. Press the “on” or “off” button on the touchscreen to turn the navigation turn-by-turn in cluster on or off. Units • units when in this display, you may select ...

  • Page 216

    • pressure set to: “bar.” • temperature set to: “°c.” custom units can be customized independently from: • distance select from: “mi” or “km.” • fuel consumption select from: “mpg” (us), “mpg” (uk), “l/100 km” or “km/l” according to distance unit measure cho- sen. • pressure select from: “psi,” “kpa...

  • Page 217

    • sync time with gps this feature will allow you to automatically have the radio set the time. To change the sync time setting, press the “sync time with nav” button on the touchscreen. Press the “on” or “off” button on the touchscreen to turn the sync time with gps on or off. • set time hours this ...

  • Page 218

    Safety & driving assistance after pressing the “safety & driving assistance” button on the touchscreen the following settings will be avail- able: • parkview backup camera delay when the vehicle is shifted out of reverse (with camera delay turned off), the rear camera mode is exited and the navigati...

  • Page 219

    Lights after pressing the “lights” button on the touchscreen the following settings will be available: • interior ambient lights when this feature is selected, it allows the adjustment of the brightness of the interior ambient lighting. To change the interior ambient lights setting, press the “+” or...

  • Page 220

    • daytime running lights when this feature is selected, the headlights will turn on while the engine is running. To make your selection, press the “daytime running lights” button on the touch- screen, then choose “yes” or “no.” the button will highlight indicating that the setting has been selected....

  • Page 221

    • flash headlights with lock when this feature is selected, the exterior lights will flash when the doors are locked or unlocked with the remote keyless entry (rke) transmitter. This feature may be selected with or without the sound horn on lock feature selected. To make your selection, press the “f...

  • Page 222

    • sound horn with remote lock when this feature is selected, the horn will sound when the door locks are activated. To make your selection, press the “sound horn with remote lock” button on the touchscreen, then choose “yes” or “no.” the button will highlight indicating that the setting has been sel...

  • Page 223

    Entry (rke) transmitter lock or unlock buttons. To make your selection, press the “passive entry” button on the touchscreen, then choose “yes” or “no.” the button will highlight indicating that the setting has been selected. • memory linked to key fob on/off — if equipped this feature provides autom...

  • Page 224

    Seats” button on the touchscreen, then select either “off,” “remote start” or “all starts.” the button will highlight indicating that the setting has been selected. Press the back arrow button on the touchscreen to return to the previous menu. Engine off options after pressing the “engine off option...

  • Page 225

    • radio off delay when this feature is selected, the radio will stay on for a preset time after the ignition key is turned to stop. To change the radio off delay status, press the “0 min” or “20 min” button on the touchscreen to select your desired time interval. Audio after pressing the “audio” but...

  • Page 226

    • aux volume match — if equipped this feature provides the ability to tune the audio level for portable devices connected through the aux input. To make your selection, press the “aux volume match” button on the touchscreen, select on or off. • loudness — if equipped loudness improves sound quality ...

  • Page 227

    Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touch- screen, the following settings will be available: • channel skip siriusxm can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scannin...

  • Page 228

    Clear personal data after pressing the “clear personal data settings” button on the touchscreen the following settings will be avail- able: • clear personal data when this feature is selected it will remove personal data including bluetooth devices and presets. To clear per- sonal data press the “ye...

  • Page 229

    Steering wheel audio controls the remote sound system controls are located at the rear of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pushing th...

  • Page 230

    Radio operation pushing the top of the switch will “seek” up for the next listenable station and pushing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gramme...

  • Page 231

    Note: if you experience difficulty in playing a particular disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. Radio operation and mobile phone...

  • Page 232

    1. Temperature control rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the scale indicates cooler temperatures, while rotating to the right into the red area indicates warmer temperatures. 2. Recirculati...

  • Page 233

    Max a/c for maximum cooling, use the a/c and recirculation modes at the same time. Economy mode if economy mode is desired, push the a/c button to turn off the indicator light and the a/c compressor. Then, move the temperature control to the desired temperature. 5. Rear defrost control push and rele...

  • Page 234

    Require extra heat to the windshield. This setting is good for maintaining comfort while reducing mois- ture on the windshield. • defrost air is directed through the windshield and side window demister outlets. Use this mode with maximum blower and temperature settings for best windshield and side w...

  • Page 235

    Do not use the function for a long time, particularly if there are many passengers on board, to prevent the windows from misting up. Note: internal air recirculation makes it possible to reach the required heating or cooling conditions more quickly depending on the mode selected. Do not use the inte...

  • Page 236

    Button off ). This logic guarantees optimum visibility at the windows. The user can always set air recirculation and climate control system compressor. Additional electric heater (if equipped) the additional electric heater ensures more rapid passen- ger compartment heating. It activates in cold wea...

  • Page 237

    Automatic dual zone climate control system (if equipped) controls 1. Driver temperature control provides the driver with independent temperature con- trol. Rotate adjustment knob to set desired temperature. Note: in sync mode, this button will also automatically adjust the passenger temperature sett...

  • Page 238

    If the recirculation indicator is on, the recirculation setting is manual and recirculation is on. 3. Rear defrost control push and release the rear defrost control button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear wi...

  • Page 239

    Indicator illuminates when this feature is on. Perform- ing this function will cause the atc to switch into manual mode. The blower speed may increase when defrost mode is selected, the air conditioning compressor is switched on (led on button on) and the air recircu- lation is switched off (led on ...

  • Page 240

    The climate control system can recognize extremely cold (or extremely hot) conditions in the passenger compart- ment and consequently provide optimal management of the system’s capabilities. Note: the reference temperature is 72° f (22° c) for optimal comfort management. The automatically controlled...

  • Page 241

    The system allows the following to be set or adjusted manually: • driver/passenger side air temperature • fan speed (continuous variation) • air distribution to seven positions • compressor enablement • rapid defrosting/demisting function • air recirculation • heated rear window • system deactivatio...

  • Page 242

    During automatic operation, you can change the set temperatures, air distribution and fan speed at any time by using the relevant buttons or knobs: the system will automatically change the settings to adjust to the new requirements. During completely automatic operation (auto), varying the air flow ...

  • Page 243

    To deactivate these functions, turn the temperature knob to the desired temperature. Air distribution selection by pushing the mode control buttons (up/down/right arrows), it is possible to set one of the seven possible air distributions manually: • up arrow – air flow to the windshield and front si...

  • Page 244

    • up/right/down arrows – air flow distribution to all diffusers on the car. Note: air always flows from the side dashboard diffus- ers: it is, however, possible to interrupt the air flow by operating the wheel located near the corresponding vents. In auto mode, the climate control system automatical...

  • Page 245

    If the auto button is pushed when the auto led is on, the system switches to completely manual mode; it displays the current flow and distribution status, which will no longer be managed automatically. If a manual intervention is made on at least the air distribution, on compressor button or on the ...

  • Page 246

    • forced deactivation (air recirculation always off, air intake from the outside), signalled by the led on the recirculation control button switching off forced activation/deactivation can be selected by push- ing the recirculation control button. When the on/off button is pushed, the climate contro...

  • Page 247

    The system remembers that the compressor has been switched off, even after the engine has stopped. When the compressor is switched off, the system deacti- vates air recirculation to prevent the windows from misting up. Pushing the a/c button will stop the auto mode (the auto led will switch off). To...

  • Page 248

    Note: the front defrost control (max-def) function remains on for about three minutes from when the engine coolant reaches the appropriate temperature. When the function is activated, the led on the auto button switches off. With the function activated the only possible manual adjustments are adjust...

  • Page 249

    Note: do not affix stickers to the inside of the heated rear window over the heating filaments, to avoid damage that might cause them to stop working properly. Switching off the climate control system push the on/off button. With climate control system off: • air recirculation is on, thus isolating ...

  • Page 250

    Uconnect voice recognition quick tips introducing uconnect start using uconnect voice recognition with these help- ful quick tips. It provides the key voice commands and tips you need to know to control your uconnect 5.0 or 6.5a/6.5an system. Uconnect 5.0n 248 understanding your instrument panel.

  • Page 251

    Key features: • 5.0-inch color touchscreen display with am/fm/ usb/bluetooth • bluetooth with integrated voice control • gps navigation (if equipped) uconnect 6.5an 4 understanding your instrument panel 249.

  • Page 252

    Key features: • 6.5-inch color touchscreen display with am/fm/ usb/sd card/bluetooth • bluetooth with integrated voice control • gps navigation (if equipped) get started all you need to control your uconnect system with your voice are the buttons on your steering wheel. 1. Visit uconnectphone.Com to...

  • Page 253

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect system. Push the vr button . After the beep, say ѧ • cancel to stop a current voice session. • help to hear a list of suggested voice commands. • repeat to listen to the system prompts again. Noti...

  • Page 254

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio stations you would like to hear. (subscrip- tion or included siriusxm satellite radio trial required.) push the vr button . After the beep, say ѧ uconnect 5.0 uconnect 6.5a/6.5an 252 understanding your instrument panel.

  • Page 255

    • tune to ninety-five-point-five fm. • tune to satellite channel hits 1. Tip: at any time, if you are not sure of what to say or want to learn a voice command, push the vr button and say “help.” the system will provide you with a list of commands. Uconnect 5.0 radio 4 understanding your instrument p...

  • Page 256

    Media uconnect offers connections via usb port, bluetooth and auxiliary ports (if equipped). Voice operation is only available for connected usb and ipod devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands and...

  • Page 257

    Tip: press the browse button on the touchscreen to see all of the music on your ipod or usb device. Your voice command must match exactly how the artist, album, song and genre information is displayed. Uconnect 5.0 media uconnect 6.5a/6.5an media 4 understanding your instrument panel 255.

  • Page 258

    Phone making and answering hands-free phone calls is easy with uconnect. When the phonebook button is illumi- nated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Push the phone button . After the beep, say one of the follo...

  • Page 259

    Navigation (6.5a/6.5an) the uconnect navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. 1. To enter a destination, push the vr button . After the beep, say: • for the 6.5an uconnect system, say: “navigate to 800 chrysler drive ...

  • Page 260

    Voice text reply uconnect will announce incoming text messages. Push the phone button and say “listen.” (must have compatible mobile phone paired to uconnect system.) 1. Once an incoming text message is read to you, push the phone button . After the beep, say: “reply.” 2. Listen to the uconnect prom...

  • Page 261

    Pre-defined voice text reply responses i’ll call you later. I need directions. See you in of minutes. I’m on my way. Can’t talk right now. I’m lost. Thanks. Tip: your mobile phone must have the full implementa- tion of the message access profile (map) to take advan- tage of this feature. For details...

  • Page 262

    Additional information © 2015 fca us llc. All rights reserved. Mopar and uconnect are registered trademarks and mopar owner connect is a trademark of fca us llc. Android is a trademark of google inc. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. Uconnect system suppo...

  • Page 263: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .265 ▫ manual transmission — if equipped . . . . . . .265 ▫ automatic transmission — if equipped . . . . .265 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .265 ▫ cold weather operation . . . . . . . ....

  • Page 264

    䡵 driving on slippery surfaces . . . . . . . . .291 ▫ acceleration . . . . . . . . . . . . . . . . . . . . . . . . .291 ▫ traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .291 䡵 driving through water . . . . . . . . . . . . .292 ▫ flowing/rising water . . . . . . . . . . . . . . . . . ...

  • Page 265

    ▫ tire inflation pressures . . . . . . . . . . . . . . . . .319 ▫ tire pressures for high speed operation . . . .321 ▫ radial ply tires . . . . . . . . . . . . . . . . . . . . . .321 ▫ tire types . . . . . . . . . . . . . . . . . . . . . . . . . . .322 ▫ run flat tires — if equipped . . . . . . . . ...

  • Page 266

    䡵 recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . . . .345 ▫ towing this vehicle behind another vehicle . .345 264 starting and operating.

  • Page 267

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 268

    Turn the ignition switch to the avv/acc (start) position and release it when the engine starts. If the engine fails to start within 10 seconds, turn the ignition switch to the stop (off/lock) position, wait 10 to 15 seconds, then repeat the “normal starting” procedure. Cold weather operation to prev...

  • Page 269

    3. If the engine fails to start within ten seconds, cycle the ignition to the stop (off/lock) position, wait five seconds to allow the starter to cool, then repeat the extended park starting procedure. 4. If the engine fails to start after eight attempts, allow the starter to cool for at least 10 mi...

  • Page 270

    After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Turbo charger “cool down” this vehicle is equipped with an after-run pump to cool the turbocharger after the engine is shut off. Depending on the type of driving and the amount of cargo, the pump w...

  • Page 271

    Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can result from starting in third. For most city driving you will find it easier to use only the lower gears. For steady highway ...

  • Page 272

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 273

    Note: you must press and hold the brake pedal while shifting out of park. Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You c...

  • Page 274

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock/ off (key removal) position. The key can only be re- moved from the ignition when the ignition is in the lock/o...

  • Page 275

    This transmission is programmed to prevent shifting from reverse to drive or drive to reverse, if vehicle speed is above 6 mph (10 km/h). This safety feature helps protect your transmission from damage. Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle i...

  • Page 276

    Note: if the shift lever cannot be moved to the park, reverse, or neutral position (when pushed for- ward) it is probably in the autostick (+/-) position (beside the drive position). In autostick mode, the transmission gear (1, 2, 3, etc.) is displayed in the instrument cluster. Move the shift lever...

  • Page 277

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not in park. Check by trying to move the gear...

  • Page 278

    Warning! (continued) number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector. • do not leave the ignition key in or near the vehicle (or in a location accessible to children). A child could...

  • Page 279

    Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral (n) use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake an...

  • Page 280

    To a manual transmission. Therefore, you should become familiar with some of the normal operational character- istics of this transmission: • during low-speed driving conditions in first gear, vehicle momentum changes may feel exaggerated in response to changes in accelerator pedal position. This be...

  • Page 281

    During extremely cold temperatures, the transmission will not operate if the oil temperature is -22°f (-30°c) or below. Allow the engine to idle briefly with the transmis- sion in park in order to warm the fluid. Normal operation will resume once the transmission temperature has risen to a suitable ...

  • Page 282

    Message description shift to neutral – then drive or reverse the transmission has shifted itself into neutral (due to a fault condition, or overheat due to excessive idling when stopped in drive with the brakes re- leased), but the shift lever remains in gear. Shift into neutral and then back into g...

  • Page 283

    Message description transmission getting hot press brake the transmission driving clutch is overheating, usu- ally due to repeated launches in stop-and-go traffic. Pull over and allow the transmission to cool in neu- tral until “transmission cool ready to drive” is displayed. Trans. Hot stop safely ...

  • Page 284

    Message description set park brake the sensor that confirms park engagement is not functioning properly. Engage the parking brake to en- sure that the vehicle will not roll when in park. Transmission limp home mode transmission function is monitored electronically for abnormal conditions. If a condi...

  • Page 285

    Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required...

  • Page 286

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has park, reverse, neu- tral, drive, and autostick (+/-) shift positions. Manual sh...

  • Page 287

    When parking on a level surface, you may shift the transmission into park first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting the transmission to park, otherwise the load on the transmission locking mechanism may make it difficult to move the shif...

  • Page 288

    Warning! (continued) the engine off, apply the parking brake, and remove the ignition key. When the ignition is in the lock/off (key removal) position, an automatic transmission is locked in park, securing the ve- hicle against unwanted movement. • when leaving the vehicle, always remove the igni- t...

  • Page 289

    • look at the transmission gear position display and verify that it indicates the park position (p). • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a ...

  • Page 290

    Drive position provides optimum driving characteris- tics under all normal operating conditions. When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading condi- tions, in hilly terrain, or traveling into strong head winds), use the autostick shift control (r...

  • Page 291

    1. Stop the vehicle. 2. Shift the transmission into park. 3. Turn the ignition switch to the off position. 4. Wait approximately 10 seconds. 5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even...

  • Page 292

    Note: in autostick mode, the transmission will only shift up or down when the driver moves the shift lever rearward (+) or forward (-), except as described below. • the transmission will automatically upshift when nec- essary to prevent engine over-speed. • the transmission will automatically downsh...

  • Page 293

    Position at any time without taking your foot off the accelerator pedal. Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Driving on slippery surfaces acceleration...

  • Page 294

    2. Slow down if the road has standing water or puddles. 3. Replace the tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. Driving through w...

  • Page 295

    Warning! • driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • driving through standing water limits your vehi- cle’s braking capabilities, which increases stopping distances. Therefore, after driving throu...

  • Page 296

    Caution! (continued) damage is not covered by the new vehicle limited warranty. • getting water inside your vehicle’s engine can cause it to lock up and stall out, and cause serious internal damage to the engine. Such damage is not covered by the new vehicle limited warranty. Electric power steering...

  • Page 297

    When the parking brake is applied with the ignition switch in the mar (acc/on/run) position, the brake warning light in the instrument cluster will illuminate. When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill gra...

  • Page 298

    Warning! (continued) • be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury. Also be certain to leave a manual transmis- ...

  • Page 299

    Electronic brake control system your vehicle is equipped with a advanced electronic brake control system that includes the anti-lock brake system (abs), brake assist system (bas), traction con- trol system (tcs), hill start assist (hsa), dynamic steering torque (dst), and electronic stability contro...

  • Page 300

    Warning! (continued) • the abs cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • the capabilities of an abs-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize t...

  • Page 301

    Warning! • the brake assist system (bas) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevail- ing road conditions. • the bas cannot prevent collisions, including those resulting from excessive speed in turns, driving on very sli...

  • Page 302

    Short period of time, the system will release brake pressure and the vehicle will roll down the hill. The system will release brake pressure in proportion to the amount of throttle applied as the vehicle starts to move in the intended direction of travel. Hsa activation criteria the following criter...

  • Page 303

    In critical situations (braking with different grip condi- tions), through the dst function the esc system controls the steering to implement an additional torque contribu- tion on the steering wheel, to suggest the most correct manoeuvre to the driver. The coordinated action of brakes and steering ...

  • Page 304

    Warning! (continued) hydroplaning. Esc also cannot prevent collisions resulting from loss of vehicle control due to inap- propriate driver input for the conditions. Only a safe, attentive, and skillful driver can prevent acci- dents. The capabilities of an esc equipped vehicle must never be exploite...

  • Page 305

    On after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. The esc activation/malfunction indicator light (located in the instrument ...

  • Page 306

    Partial off the “esc off” button is located in the switch bank above the climate control. To enter the “partial off” mode, momentarily push the “esc off” button and the “esc activation/malfunction indicator light” will illu- minate. To turn the esc on again, momentarily push the “esc off” button and...

  • Page 307

    Note: to improve the vehicle’s traction when driving with snow chains, or when starting off in deep snow, sand, or gravel, it may be desirable to switch to the “partial off” mode by momentarily pushing the “esc off” button. Once the situation requiring “partial off” mode is overcome, turn esc back o...

  • Page 308

    Warning! Many factors, such as vehicle loading, road condi- tions, and driving conditions, influence the chance that wheel lift or rollover may occur. Erm cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. The capabili...

  • Page 309

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ...

  • Page 310

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or ⴖ....Blank....ⴖ = passenger car tire based on european design standards, or lt = light truck tire based o...

  • Page 311

    Example: service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions – the maximum speed corres...

  • Page 312

    Tire identification number (tin) the tin may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full tin, including the date code, located on the white sidewall side of the tire. Look for the tin on the outboard side of...

  • Page 313

    Example: dot ma l9 abcd 0301 01 = number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – prior to july 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represen...

  • Page 314

    Term definition maximum inflation pressure the maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire. The maximum inflation pressure is molded into the sidewall. Recommended cold tire inflation pressure vehicle manufacturer’s recommended cold tire inflation...

  • Page 315

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) 5 starting and operating 313.

  • Page 316

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. Example tire placard location (b-pillar) tire and loading information p...

  • Page 317

    4. Cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and co...

  • Page 318

    “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 lbs (68 kg) = 750 lbs (340 kg), and 1400 lbs (635 kg) – 750 lbs (340 kg) = 650 lbs [295 kg]). 5. Determi...

  • Page 319

    5 starting and operating 317.

  • Page 320

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 321

    Warning! (continued) • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering. Note: • unequal tire press...

  • Page 322

    Judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and ...

  • Page 323

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 324

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed symbol). Tire ...

  • Page 325

    Warning! Do not use summer tires in snow/ice conditions. You could lose vehicle control, resulting in severe injury or death. Driving too fast for conditions also creates the possibility of loss of vehicle control. Snow tires some areas of the country require the use of snow tires during the winter....

  • Page 326

    Run flat tire reaches the run flat mode it has limited driving capabilities and needs to be replaced immedi- ately. A run flat tire is not repairable. It is not recommended driving a vehicle loaded at full capacity or to tow a trailer while a tire is in the run flat mode. See the tire pressure monit...

  • Page 327

    Compact spare tire — if equipped the compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on the tire and loading information placard located on the driver’s side door opening or on the sidewall ...

  • Page 328

    Spare tire needs to be replaced. Since it is not the same as your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the first opportunity. Limited-use spare — if equipped the limited-use spare tire is for temporary emergency use only. This tire ...

  • Page 329

    Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels fast...

  • Page 330

    Worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. Life of tire the service life of a tire is dependent upon varying factors including, but not limited to: • driving style. • tire pressure - improper cold tire inflati...

  • Page 331

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance w...

  • Page 332

    Warning! (continued) braking of your vehicle. This can cause unpredict- able handling and stress to steering and suspen- sion components. You could lose control and have a collision resulting in serious injury or death. Use only the tire and wheel sizes with load ratings approved for your vehicle. •...

  • Page 333

    Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device cleara...

  • Page 334

    Tire rotation recommendations the tires on the front and rear of your vehicle operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation a...

  • Page 335

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12°f (6.5°c). This means that when the outsi...

  • Page 336

    Driven for up to 20 minutes above 15 mph (24 km/h) in order for the tpms to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) tire pressure of 30 psi (207 kpa). If the ambient temperature is 68°f (20°c) and the measured tire pressure i...

  • Page 337

    Caution! (continued) stem, which could damage the tire pressure moni- toring sensor. Note: • the tpms is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • the tpms should not be used as a tire pressure gauge while adjusting your tire pr...

  • Page 338

    Note: it is particularly important for you to check the tire pressure in all of the tires on your vehicle regularly and to maintain the proper pressure. The tpms consists of the following components: • receiver module. • four tire pressure monitoring sensors. • tire pressure monitoring telltale ligh...

  • Page 339

    • installing some form of aftermarket window tinting that affects radio wave signals. • snow or ice around the wheels or wheel housings. • using tire chains on the vehicle. • using wheels/tires not equipped with tpm sensors. Note: your vehicle may be equipped with a compact spare wheel and tire asse...

  • Page 340

    General information this device complies with part 15 of the fcc rules and rss-210 of industry canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may caus...

  • Page 341

    Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before consid- ering service for the vehicle. Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referre...

  • Page 342

    Are not the responsibility of the manufacturer and may void or not be covered under new vehicle limited warranty. Mmt in gasoline methylcyclopentadienyl manganese tricarbonyl (mmt) is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended wit...

  • Page 343

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gasoline is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition ...

  • Page 344

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 345

    5. Remove the fuel nozzle and close the fuel door. Note: a funnel is provided (located in the tool bag or cargo floor area in the rear cargo area) to open the flapper door to allow for emergency refueling with a gas can. Funnel location inside of tool kit funnel location for vehicle with optional sp...

  • Page 346

    Caution! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Warning! • never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled. • never add fuel when the engine is running. This is in violation of most stat...

  • Page 347

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmis- sion euro twin clutch transmission automatic trans- mission (aisin aw6f25 transmission ) flat tow none transmission in neutral transmission in neutral not a...

  • Page 348

    Vehicles equipped with a manual transmission, or a euro twin clutch transmission, may be flat towed (with all four wheels on the ground) at any legal highway speed, for any distance, if the transmission is in neutral. To place the euro twin clutch transmission in neu- tral, follow the procedure belo...

  • Page 349: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .349 䡵 if your engine overheats . . . . . . . . . . . .349 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .350 ▫ torque specifications . . . . . . . . . . . . . . . . . . .351 䡵 tire se...

  • Page 350

    ▫ euro twin clutch transmission. . . . . . . . . . . .374 ▫ automatic transmission . . . . . . . . . . . . . . . . .375 䡵 ignition key removal override . . . . . . .376 䡵 cap-less fuel fill funnel . . . . . . . . . . . .378 348 what to do in emergencies.

  • Page 351

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the radio. Push the switch to turn on the hazard warning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the ...

  • Page 352

    Supplement to the radiator and aids in removing heat from the engine cooling system. Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at...

  • Page 353

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/ bolt socket size 63 ft-lbs (86 n·m) steel wheels only 89 ft-lbs (120 n·m) aluminum wheels only m12 x 1.25 17 mm **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. ...

  • Page 354

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten...

  • Page 355

    Tire punctures of up to 1/4” (6mm) can be repaired; the kit can be used in all weather conditions. Do not remove the foreign object from the punctured tire,i.E., screw or nail. Remove the tire service kit from the vehicle, take it out from the bag and place it near the punctured tire. Screw the clea...

  • Page 356

    Warning! (continued) – if the tire has any sidewall damage. – if the tire has any damage from driving with extremely low tire pressure. – if the tire has any damage from driving on a flat tire. – if the wheel has any damage. – if you are unsure of the condition of the tire or the wheel. • keep tire ...

  • Page 357

    Push the tire service kit power button to the “i” position. The electric compressor will be turned on, sealant and air will inflate the tire. Minimum 26 psi (1.8 bar) of pressure should be reached within 20 minutes. If the pressure has not been reached, turn off and remove the tire service kit, driv...

  • Page 358

    Warning! The metal end fitting from power plug may get hot after use, so it should be handled carefully. Note: replace the sealant canister prior to the expira- tion date at your authorized dealer. Warning! Store the sealant canister in its special compartment, away from sources of heat. Failure to ...

  • Page 359

    Jacking and tire changing — if equipped warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehi...

  • Page 360

    Jack location the spare tire jack is located in the rear cargo area underneath the cargo floor. Jack location 1 — emergency fuel fill funnel 2 — jack 3 — jack handle 4 — emergency allen key 5 — emergency spare tire bag 6 — emergency screwdriver 358 what to do in emergencies.

  • Page 361

    Spare tire removal the spare tire is stowed in underneath the rear cargo area on the outside of the car. 1. Remove the cargo floor to access the winch. 2. Remove the jack handle and use the wrench end to lower the spare tire. 3. When the spare is clear, replace the jack tools. Spare tire location wi...

  • Page 362

    Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the whe...

  • Page 363

    Warning! (continued) • turn on the hazard warning flasher. • block the wheel diagonally opposite the wheel to be raised. • set the parking brake firmly and set an euro twin clutch transmission in park; a manual transmis- sion in reverse. • never start or run the engine with the vehicle on a jack. • ...

  • Page 364

    3. Before raising the vehicle, use the wheel bolt wrench to loosen, but not remove, the wheel bolts on the wheel with the flat tire. Turn the wheel bolts counter- clockwise one turn while the wheel is still on the ground. Note: there are front and rear jacking locations on each side of the body (as ...

  • Page 365

    Engage the jack saddle with the lift area of the sill flange, centering the jack saddle between the locating notches on the sill flange. 5. Raise the vehicle just enough to remove the flat tire and install the spare tire. Warning! Raising the vehicle higher than necessary can make the vehicle less s...

  • Page 366

    Warning! • to avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. • to avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp...

  • Page 367

    Cover the flat tire with the emergency spare tire bag and stow the flat tire into the trunk. Caution! The winch mechanism is designed for use with the jack wrench extension tool only. Use of air wrench or power tool may damage the winch. Jump-starting procedure if your vehicle has a discharged batte...

  • Page 368

    Preparations for jump-start the battery in your vehicle is located on the drivers side of the engine compartment. Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove an...

  • Page 369

    3. Remove the protective cover over the remote positive (+) battery post. To remove the cover, pull upward on the cover. 4. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not al...

  • Page 370

    Follow these steps to disconnect the negative (-) battery cable: 1. Pull outward on the negative (-) battery cable terminal release lever to the open position. 2. Lift up on the negative (-) battery cable terminal and set aside. Connecting the jumper cables 1. Connect the positive (+) end of the jum...

  • Page 371

    Disconnecting the jumper cables 1. Disconnect the negative (-) jumper cable from the negative (-) battery cable terminal of the vehicle with the discharged battery. 2. Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery. 3. Disconnect the po...

  • Page 372

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse (with automatic or euro twin clutch transmis...

  • Page 373

    Caution! • when “rocking” a stuck vehicle by shifting be- tween drive/2nd gear and reverse, do not spin the wheels faster than 15 mph (24 km/h), or drive- train damage may result. • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damag...

  • Page 374

    4. Press and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool into the shift lever override access hole (at the right rear corner of the shift lever assembly) and push and hold the override release lever down. 6. Move the shift lever to the neutral position. 7...

  • Page 375

    Towing a disabled vehicle note: this section describes procedures for towing a disabled vehicle using a commercial towing service. Towing condition wheels off the ground manual trans- mission euro twin clutch trans- mission automatic (ai- sin aw6f25) transmission flat tow none trans in neutral trans...

  • Page 376

    Caution! • do not use sling-type equipment when towing. Vehicle damage may occur. • when securing the vehicle to a flatbed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. If you must use the accessories (wipers, defroster, etc.) wh...

  • Page 377

    Section for instructions on shifting the transmission out of park for towing. Caution! • towing this vehicle in violation of the above re- quirements can cause severe transmission damage. Damage from improper towing is not covered un- der the new vehicle limited warranty. Automatic transmission • ve...

  • Page 378

    Ignition key removal override this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock/ off (key removal) position. To remove the key manually, proceed as follows: 1. Firmly apply the parking brak...

  • Page 379

    6. Pull the release tab downwards using one hand and with the other one remove the key, sliding it outwards. 7. Once the key is removed, reinstall the steering column cover. Caution! It is advisable to contact your authorized dealer to have the reinstall procedure carried out. If you would like to p...

  • Page 380

    Cap-less fuel fill funnel the funnel for the cap-less fuel system is located in the rear cargo area inside the tool bag (if equipped), or on the left side in the cargo box. If your vehicle is out of fuel and an auxiliary fuel can is needed, insert the funnel into the filler neck and proceed to fill ...

  • Page 381: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 1.4l turbo . . . .381 䡵 onboard diagnostic system — obd ii . .382 ▫ onboard diagnostic system (obd ii) cybersecurity . . . . . . . . . . . . . . . . . . . . . . . .382 䡵 replacement parts . . . . . . . . . . . . . . . . . .383 䡵 dealer service...

  • Page 382

    ▫ euro twin clutch transmission — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .407 ▫ automatic transmission — aisin aw6f25 transmission — if equipped . . . . . . . . . . . . .409 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .411 ...

  • Page 383

    Engine compartment — 1.4l turbo 1 — air cleaner filter 4 — battery 7 — coolant pressure cap 2 — engine oil dipstick 5 — front distribution unit (fuses) 8 — coolant pressure bottle 3 — brake fluid reservoir 6 — washer fluid reservoir 9 — oil fill cap 7 maintaining your vehicle 381.

  • Page 384

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and euro twin clutch transmission control systems. When these sys- tems are operating properly, your vehicle will p...

  • Page 385

    Access this information to assist with the diagnosis and service of your vehicle and emissions system. Warning! • only an authorized service technician should con- nect equipment to the obd ii connection port in order to diagnose or service your vehicle. • if unauthorized equipment is connected to t...

  • Page 386

    Note: intentional tampering with emissions control systems may void your warranty and could result in civil penalties being assessed against you. Warning! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If...

  • Page 387

    Caution! (continued) transmission, or air conditioning. Such damage is not covered by the new vehicle limited warranty. If a flush is needed because of component malfunc- tion, use only the specified fluid for the flushing procedure. Engine oil checking oil level to assure proper engine lubrication,...

  • Page 388

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” for further informa- tion. Note: under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve month...

  • Page 389

    The engine oil. Engine oil is an engineered product and its performance may be impaired by supplemental addi- tives. Disposing of used engine oil and oil filters care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discard...

  • Page 390

    Warning! (continued) vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury. Engine air cleaner filter selection the quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be us...

  • Page 391

    Warning! (continued) • the battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented). Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and th...

  • Page 392

    Warning! (continued) • the air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. Caution! Do not use chemical flushes...

  • Page 393

    3. Pivot the glove compartment downward. 4. Disengage the retaining tabs that secure the air filter access door to the hvac housing. 5. Open the air filter access door. A/c air filter access door a/c air filter access door open 7 maintaining your vehicle 391.

  • Page 394

    6. Remove the particulate air filters from the hvac air inlet housing. Pull the filter elements straight out of the housing. 7. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. Caution! The a/c air filter is identified with an arrow to ind...

  • Page 395

    Should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mecha- nism and safety catch sh...

  • Page 396

    Service position strategy the service position allows the wiper blades to be placed in a position that allows the wiper blades to be easily changed. To enable the service position strategy the wipers must be in the park position before placing the ignition in the stop/off position. Service mode must...

  • Page 397

    Front wiper blade removal/installation 1. Lift the front wiper arm upward to raise the wiper blade off of the windshield. 2. Push the release button on the arm of the wiper blade. 3. Push the wiper blade up the and remove it. 4. Install the wiper blade and firmly push the wiper blade until it snaps ...

  • Page 398

    Rear wiper blade removal/installation 1. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 2. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder. 3. Install the wiper blade pivot pin into the wiper blade...

  • Page 399

    Adding washer fluid the windshield washer fluid reservoir is located in the engine compartment, and the fluid level should be checked at regular intervals. Fill the reservoir with wind- shield washer solvent (not engine coolant/ antifreeze). Refer to “engine compartment” in this section for fur- the...

  • Page 400

    Warning! (continued) to know before starting your vehicle” for further information. • a hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your ve- hicle in areas w...

  • Page 401

    Note: intentional tampering with emissions control systems can result in civil penalties being assessed against you. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn ...

  • Page 402

    Coolant checks check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- freeze). Check...

  • Page 403

    Caution! (continued) hybrid organic additive technology (hoat) en- gine coolant (antifreeze) or any “globally compat- ible” coolant (antifreeze). If a non-oat engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and r...

  • Page 404

    • mix a minimum solution of 50% oat engine coolant that meets the requirements of fca material standard ms.90032 and distilled water. Use higher concentra- tions (not to exceed 70%) if temperatures below −34°f (−37°c) are anticipated. • use only high purity water such as distilled or deion- ized wat...

  • Page 405

    The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. Warning! • do not open hot engine cooling system. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat ...

  • Page 406

    When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine co...

  • Page 407

    Only the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emis- sions. Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “mai...

  • Page 408

    Brake fluid reservoir is low and the brake system does not indicate any leaks or other problems, it may be a result of a leak in the hydraulic clutch release system. See your local authorized dealer for service. Use only manufacturer’s recommended brake fluid. Re- fer to “fluids, lubricants, and gen...

  • Page 409

    Caution! Use of improper brake fluids will affect overall clutch system performance. Improper brake fluids may damage the clutch system resulting in loss of clutch function and the ability to shift the transmis- sion. Manual transmission — if equipped lubricant selection use only the manufacturers r...

  • Page 410

    The transmission fluid at the correct level using the recommended fluid. No chemical flushes should be used in any transmission; only the approved lubricant should be used. Special additives the manufacturer strongly recommends against using any special additives in the transmission. Transmission fl...

  • Page 411

    Caution! If a transmission fluid leak occurs, visit your autho- rized dealer immediately. Severe transmission dam- age may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid changes under normal operating conditions, the fluid installed at the factory will...

  • Page 412

    Caution! (continued) in transmission shift quality and/or torque converter shudder. Refer to “fluids, lubricants, and genuine parts” in this section for fluid specifications. Special additives the manufacturer strongly recommends against using any special additives in the transmission. Automatic tra...

  • Page 413

    Caution! If a transmission fluid leak occurs, visit your autho- rized dealer immediately. Severe transmission dam- age may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid and filter changes under normal operating conditions, the fluid installed at the f...

  • Page 414

    • insects, tree sap and tar. • salt in the air near seacoast localities. • atmospheric fallout/industrial pollutants. Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar car wash, or a mild car wash soap, and rinse the panels completely with clear water. • if i...

  • Page 415

    • it is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is ...

  • Page 416

    Caution! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s pro- tective finish. Only mopar wheel...

  • Page 417

    Can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar total clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cl...

  • Page 418

    Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses ...

  • Page 419

    Instrument panel bezels caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Cleaning plastic instrument cluster lenses the...

  • Page 420

    Warning! (continued) damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (i.E., bent retractor, torn web- bing, etc.). Fuses warning! • when replacing a blown fuse, always use an ap- pr...

  • Page 421

    Underhood fuses the front distribution unit is located on the right side of the engine compartment, next to the battery. To access the fuses, push the release tabs and remove the cover. The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Fron...

  • Page 422

    Cavity maxi fuse mini fuse description f01 70 amp tan – body controller f02 60 amp blue – body controller rear distribution unit f03 20 amp yellow – ignition switch f04 40 amp orange – anti-lock brake pump f05 70 amp tan – electric power steering f06 30 amp green – radiator fan - low speed f07 50 am...

  • Page 423

    Cavity maxi fuse mini fuse description f16 – 7.5 amp brown transmission powertrain f17 – 10 amp red powertrain f18 – 5 amp tan powertrain (multiair – if equipped) f19 – 7.5 amp brown air conditioning f20 – 30 amp green rear defroster f21 – 15 amp blue fuel pump f22 – 20 amp yellow powertrain f23 – 2...

  • Page 424

    Interior fuses the interior fuse panel is part of the body control module (bcm) and is located on the driver’s side under the instrument panel. Interior fuse panel 422 maintaining your vehicle.

  • Page 425

    Fuse panel cavity locations 7 maintaining your vehicle 423.

  • Page 426

    Cavity vehicle fuse number mini fuse description 1 f12 7.5 amp brown right low beam 2 f32 7.5 amp brown front and rear ceiling lights trunk and door courtesy lights 3 f53 7.5 amp brown instrument panel node 4 f38 20 amp yellow central door locking 5 f36 15 amp blue diagnostic socket, vehicle radio, ...

  • Page 427

    Cavity vehicle fuse number mini fuse description 13 f43 20 amp yellow bi-directional washer 14 f48 20 amp yellow passenger power window 15 f13 7.5 amp brown left low beam, headlamp leveling 16 f50 7.5 amp brown airbag 17 f51 5 amp tan vehicle radio switch, climate control sys- tem, stop light, clutc...

  • Page 428

    Rear interior fuses the rear interior fuse panel is located on the driver’s side in the rear compartment. Cavity vehicle fuse number mini fuse description 1 f61 15 amp blue lumbar regulation seats 2 f62 15 amp blue heated seats 3 f64 20 amp yellow hi fi system rear fuse panel 426 maintaining your ve...

  • Page 429

    Cavity vehicle fuse number mini fuse description 4 f65 20 amp yellow sun blind 5 f66 20 amp yellow sunroof vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • disconnect the negative cable from the battery. • anyt...

  • Page 430

    Replacement bulbs interior bulbs bulb number overhead lamp c5w sun visors c5w courtesy lamp w5w glove compartment c5w rear courtesy lamp c5w exterior bulbs bulb number front low and high beam headlamp hir2ll front turn signal lamps wy21w front parking/daytime running lamps w21/5w front side marker l...

  • Page 431

    Bulb number rear tail/stop lamps p21/5w rear tail lamp led (see authorized dealer) rear turn signal lamps p21w rear backup lamps w16w rear side marker lamps led (see authorized dealer) center high mounted stop lamp led (see authorized dealer) front fog lamps h11 rear fog lamps - if equipped w16w lic...

  • Page 432

    Bulb replacement note: lens fogging can occur under certain atmo- spheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. Headlamps low beam and high beam 1....

  • Page 433

    2. Rotate the bulb counterclockwise. 3. Remove the bulb when all the tabs are aligned with the openings in the metal holder. 4. Disconnect the electrical connector from the bulb. Bulb removal procedure electrical connector removal 7 maintaining your vehicle 431.

  • Page 434

    5. Install the new bulb and rotate clockwise to lock in place. 6. Reinstall the plastic cap. New bulb installation headlamp sealing cap installation 432 maintaining your vehicle.

  • Page 435

    Front turn signal, parking and daytime running lamps 1. Turn front wheels inboard to access upper cover in wheel liner. 2. Open the upper cover on the front of the wheel liner. 3. Remove the cap from the back of the lower headlamp housing. 4. Rotate the bulb counterclockwise and remove. 5. Install t...

  • Page 436

    5. Remove the two screws that secure the backplate to the tail lamp housing. 6. Separate the backplate from the tail lamp housing. 7. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counterclockwise. 8. Remove the backup lamp bulb by pulling straight out. 9. Replace ...

  • Page 437

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant – 1.4l turbo engine we recommend you use mopar antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of fca material standard ms-...

  • Page 438

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 439

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped we recommend you use mopar c series manual & dual dry clutch transmission fluid. Euro twin clutch transmission – if equipped gearbox: use only mopar c series manual & dual dry clutch transmission fluid or equivalen...

  • Page 441: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . . .440 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .442 8.

  • Page 442

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate in th...

  • Page 443

    Once a month or before a long trip: • check engine oil level. • check windshield washer fluid level. • check the tire inflation pressures and look for unusual wear or damage. • check the fluid levels of the coolant reservoir, and brake master cylinder reservoir, and fill as needed. • check function ...

  • Page 444

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176...

  • Page 445

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 446

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 447

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 448

    Warning! (continued) service job, take your vehicle to a competent me- chanic. • failure to properly inspect and maintain your ve- hicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident. 446 maintenance schedules.

  • Page 449: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .449 ▫ prepare for the appointment. . . . . . . . . . . . .449 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .449 ▫ be reasonable with requests ....

  • Page 450

    ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .455 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .455 448 if you need consumer assistance.

  • Page 451

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 452

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 453

    Has access to a tdd or a conventional teletypewriter (tty) in the united states, can communicate with the manufacturer by dialing 1-800-380-chry. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by bell canada. For tty teletypewrite...

  • Page 454

    Sincere efforts to resolve any warranty issues or related concerns. Warning! Engine exhaust (internal combustion engines only), some of its constituents, and certain vehicle compo- nents contain, or emit, chemicals known to the state of california to cause cancer and birth defects, or other reproduc...

  • Page 455

    You can also obtain other information about motor vehicle safety from http://www.Safercar.Gov. In canada if you believe that your vehicle has a safety defect, you should contact the customer service department imme- diately. Canadian customers who wish to report a safety defect to the canadian gover...

  • Page 456

    Problems the first time, using step-by-step troubleshoot- ing and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment. Owner’s manuals these owner’s manuals have been prepared with the assistance of service and engineering specialists to ac- quaint you with...

  • Page 457

    Significantly from the norm due to variations in driving habits, service practices, and differences in road charac- teristics and climate. Traction grades the traction grades, from highest to lowest, are aa, a, b, and c. These grades represent the tire’s ability to stop on wet pavement, as measured ...

  • Page 458

    Warning! (continued) excessive speed, under-inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure. 456 if you need consumer assistance.

  • Page 459: Index

    Index 10

  • Page 460

    Adding engine coolant (antifreeze) . . . . . . . . . . . .401 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .342 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .397 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .340 air bag . . . . . . . . ....

  • Page 461

    Automatic transmission . . . . . . . . . . .270, 283, 409, 411 adding fluid . . . . . . . . . . . . . . . . . . . . . . .410, 411 autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289 fluid and filter changes . . . . . . . . . . . . . . . . . .411 fluid change . . . . . . . . . . . ...

  • Page 462

    Cellular phone . . . . . . . . . . . . . . . . . . . . . . . . . . .229 center high mounted stop light . . . . . . . . . . . . . .434 chains, tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .330 changing a flat tire . . . . . . . . . . . . . . . . . . . . . . .357 chart, tire sizing . ....

  • Page 463

    Adding coolant (antifreeze) . . . . . . . . . . . . . . .401 coolant level . . . . . . . . . . . . . . . . . . . . . .400, 403 disposal of used coolant . . . . . . . . . . . . . . . . .403 drain, flush, and refill . . . . . . . . . . . . . . . . . . .400 inspection . . . . . . . . . . . . . . . . . ...

  • Page 464

    Electronic throttle control warning light . . . . . . . .172 electronic vehicle information center (evic) . .131, 186 exit trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192 start of trip procedure . . . . . . . . . . . . . . . . . . .192 emergency deck lid release . . . . . . . . ....

  • Page 465

    Filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .387 air conditioning . . . . . . . . . . . . . . . . . . . . . . .390 engine fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .435 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .387 engine oil disposa...

  • Page 466

    Gear ranges . . . . . . . . . . . . . . . . . . . . . . . . .274, 284 gear select lever override . . . . . . . . . . . . . . . . . .371 general maintenance. . . . . . . . . . . . . . . . . . . . . . .384 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .416 hazard driving through f...

  • Page 467

    Passive entry programming . . . . . . . . . . . . . . . .219 unlock liftgate . . . . . . . . . . . . . . . . . . . . . . . . .219 key, replacement . . . . . . . . . . . . . . . . . . . . . . . . . .15 keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 key, sentry (immobiliz...

  • Page 468

    Locks child protection . . . . . . . . . . . . . . . . . . . . . . . . .25 door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 lubrication, body . . . . . . . . . . . . . . . . . . . . . . . . .392 lug nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .350 mainten...

  • Page 469

    Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .385 disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .387 filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .387 filter disposal . . . . . . . . . . . . . . . . . . . . . . . . .387 materials added...

  • Page 470

    Rear window features . . . . . . . . . . . . . . . . . .156, 158 reclining rear seats . . . . . . . . . . . . . . . . . . . . . . .101 recorder, event data . . . . . . . . . . . . . . . . . . . . . . .58 recreational towing . . . . . . . . . . . . . . . . . . . . . . .345 reformulated gasoline . . ....

  • Page 471

    Seat belt maintenance . . . . . . . . . . . . . . . . . . . . . .417 seat belt reminder . . . . . . . . . . . . . . . . . . . . . . . . .33 seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32, 83 child restraint . . . . . . . . . . . . . . . . . . . . . . . . . .59 front seat . . ...

  • Page 472

    Steering tilt column . . . . . . . . . . . . . . . . . . . . . . . . . . .120 wheel, tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 steering wheel audio controls . . . . . . . . . . . . . . .227 steering wheel mounted sound system controls . . .227 storage . . . . . . . . . . . . . ...

  • Page 473

    Spare tire . . . . . . . . . . . . . . . . . . . . . .324, 325, 326 spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .326 tread wear indicators . . . . . . . . . . . . . . . . . . . .327 tire safety information . . . . . . . . . . . . . . . . . . . . .306 towing . . . . . . . . . . ....

  • Page 474

    Unleaded gasoline . . . . . . . . . . . . . . . . . . . . . . . .338 untwisting procedure, seat belt . . . . . . . . . . . . . . . .39 vehicle identification number (vin) . . . . . . . . . . . . .7 vehicle loading . . . . . . . . . . . . . . . . . . . . . . . . . .315 vehicle modifications/alteratio...

  • Page 475

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 476

    First edition printed in u.S.A. ©2015 fca us llc. All rights reserved. Fiat is a registered trademark of fca group marketing s.P.A., used under license by fca us llc. 16bf-126-aa 16bf-126-aa first edition rev. 1.