1. DL manuals
  2. Fiat
  3. Automobile
  4. 2016 500X
  5. Owner's Manual

Fiat 2016 500X Owner's Manual

Other manuals for 2016 500X: User Manual

Summary of 2016 500X

  • Page 1

    O w n e r ’ s m a n u a l 2 0 1 6 fiat 500x.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 customer assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 5: Introduction

    Introduction contents ! Introduction . . . . . . . . . . . . . . . . . . . . . . . .4 ! How to use this manual . . . . . . . . . . . . . .5 ! Warnings and cautions . . . . . . . . . . . . . .7 ! Vehicle modifications/alterations . . . .7 ! Rollover warning . . . . . . . . . . . . . . . . . . .7 1.

  • Page 6

    Introduction congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engineering spe...

  • Page 7

    How to use this manual consult the table of contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index ...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss importan...

  • Page 10

    Do not attempt sharp turns, abrupt maneuvers, or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in a collision, rollover of the vehicle, and severe or fatal injury. Drive carefully. Failure to use the driver and passenger seat b...

  • Page 11: Customer Assistance

    Customer assistance contents ! Suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . .11 ▫ prepare for the appointment . . . . . . . . . . . . .11 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . . .11 ▫ be reasonable with requests . . . . . . . . . ....

  • Page 12

    ! Department of transportation uniform tire quality grades . . . . . . . . .16 ▫ treadwear . . . . . . . . . . . . . . . . . . . . . . . . . . .17 ▫ traction grades. . . . . . . . . . . . . . . . . . . . . . . .17 ▫ temperature grades . . . . . . . . . . . . . . . . . . . .18 10 customer assistance.

  • Page 13

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 14

    Are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an ...

  • Page 15

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 16

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You will be pleased with their sincere efforts to re...

  • Page 17

    To contact nhtsa, you may either call the auto safety hotline toll free at 1-888-327-4236 (tty: 1-800-424- 9153), or go to http://www.Safercar.Gov; or write to: adminis- trator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.C. 20590. You can also obtain other information about mot...

  • Page 18

    Diagnostic procedure manuals diagnostic procedure manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and cor...

  • Page 19

    Treadwear the treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relativ...

  • Page 20

    Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the mater...

  • Page 21: Contents

    Graphical table of contents contents ! Front view . . . . . . . . . . . . . . . . . . . . . . . . . .20 ! Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . .21 ! Instrument panel . . . . . . . . . . . . . . . . . . . .22 ! Interior. . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 22

    Front view front view 1 — engine compartment 2 — headlights 3 — windshield 4 — outside mirrors 5 — doors 6 — wheels 20 graphical table of contents.

  • Page 23

    Rear view rear view 1 — rear lights 2 — rear windshield wiper 3 — liftgate 3 graphical table of contents 21.

  • Page 24

    Instrument panel instrument panel 1 — air vents 7 — upper switch bank 13 — lower switch bank 2 — multifunction lever 8 — upper storage compartment 14 — driver side knee air bag 3 — instrument cluster 9 — passenger front air bag 15 — ignition 4 — speed controls 10 — air vents 16 — driver side front a...

  • Page 25

    Interior interior features 1 — power window switches 2 — headlight switch 3 — instrument cluster 4 — audio system 5 — glove compartment 6 — seats 7 — switch panel 8 — transmission shift lever (automatic/manual options) 9 — electronic speed controls 10 — evic controls 3 graphical table of contents 23.

  • Page 27: Contents

    Getting to know your vehicle contents ! Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 ▫ mechanical key fob . . . . . . . . . . . . . . . . . . . .30 ▫ electronic key fob . . . . . . . . . . . . . . . . . . . . .31 ▫ key fob operation . . . . . . . . . . . . . . . . . . . . ....

  • Page 28

    ▫ remote start windshield wiper de–icer activation — if equipped . . . . . . . . . . . . . . . .47 ! Sentry key® . . . . . . . . . . . . . . . . . . . . . . . . .47 ▫ general information . . . . . . . . . . . . . . . . . . . .48 ! Vehicle security alarm. . . . . . . . . . . . . . .48 ▫ to arm the sy...

  • Page 29

    ▫ auto dimming mirror — if equipped. . . . . . . .80 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . .81 ▫ heated mirrors — if equipped . . . . . . . . . . . .83 ! Blind spot monitoring (bsm) — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .83 ▫ rear cross path (rcp) . ...

  • Page 30

    ▫ rain sensor — if equipped . . . . . . . . . . . . . .106 ▫ rear window wiper/washer . . . . . . . . . . . . .108 ▫ windshield wiper de-icer — if equipped . . . .109 ! Climate controls . . . . . . . . . . . . . . . . . . .110 ▫ air outlet and diffuser locations — passenger compartment . . . . . . ....

  • Page 31

    ! Internal equipment . . . . . . . . . . . . . . . . .148 ▫ glove compartments . . . . . . . . . . . . . . . . . . .148 ▫ sun visors “slide-on-rod” . . . . . . . . . . . . . .149 ▫ power outlets . . . . . . . . . . . . . . . . . . . . . . .151 ▫ cigar lighter — optional. . . . . . . . . . . . . . . ...

  • Page 32

    Keys mechanical key fob the metal insert of the key fob operates: • the ignition system • driver’s door lock mechanical key fob 1 — mechanical key 2 — door lock button 3 — door unlock button 4 — panic button 5 — mechanical key button (open/close) 30 getting to know your vehicle.

  • Page 33

    Electronic key fob on versions equipped with #keyless enter-n-go™,# the car is equipped with an electronic key fob. The key fob with remote control contains a remote keyless entry (rke) transmitter. The rke system allows you to lock or unlock the doors and liftgate or activate the panic alarm from d...

  • Page 34

    Key fob operation unlocking doors and liftgate the driver’s door may be unlocked by inserting the vehicle key into the exterior driver’s door lock cylinder. To unlock all the doors, push the interior power door unlock button on the door panel. Push and release the unlock button on the rke transmitte...

  • Page 35

    1st press of key fob unlocks this feature lets you program the system to unlock either the driver’s door or all doors on the first push of the unlock button on the rke transmitter. To change the current setting, refer to “uconnect® settings” in “multi- media” for further information. Note: if the ve...

  • Page 36

    Vehicles with keyless enter-n-go™ if one or more doors are open, or the liftgate is open, the doors will lock. The doors will unlock again only if the key is inside the passenger compartment. Note: • the current setting can be changed within the elec- tronic vehicle information center (evic) menu or...

  • Page 37

    2. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar surface. Then, replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located...

  • Page 38

    Separating keyless enter-n-go™ transmitter case 1. Remove the emergency key by sliding the mechanical latch on the back of the rke transmitter sideways with your thumb. Then, pull the key out with your other hand. 2. Separating rke halves requires screw removal (if equipped) and gently prying the tw...

  • Page 39

    Located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. To assemble the rke transmitter case, snap the two halves together and insert the emergency key. Request for additional keys ...

  • Page 40

    Note: when having the sentry key® immobilizer sys- tem serviced, bring all vehicle keys with you to an authorized dealer. Ignition switch operation your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a key fob with a remote keyle...

  • Page 41

    1 — stop/off • the engine is stopped. • the key can be removed from the ignition. • the steering column can be locked (with the ignition key removed). • some electrical devices (e.G. Power locks, alarm, etc.) are still available. 2 — mar/run • driving position. • electrical devices are available. 3 ...

  • Page 42

    Electronic key this keyless enter-n-go system feature allows the driver to operate the ignition switch with the push of a button as long as the remote keyless entry (rke) transmitter is in the passenger compartment. The keyless push button ignition has three operating positions. The three positions ...

  • Page 43

    The keyless push button ignition can be placed in the following positions: stop • the engine is stopped. • some electrical devices (e.G. Central locking, alarm, etc.) are still available. Run • driving position. • all the electrical devices are available. Start • start the engine. Note: the vehicle ...

  • Page 44

    Caution! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. Note: refer to #starting the engine# in #starting and operating# for further information. General information key fob (keyless enter-n-go) this device com...

  • Page 45

    The device is covered by: • us: continental fcc id kr5a2c91227100 • canada: model: a2c91227100 / ic: 7812d-91227100 • mexico: rlvcos114-1252 control unit (keyless enter-n-go) this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: • this device may n...

  • Page 46

    Remote start cancel message — if equipped the following messages will display in the instrument cluster if the vehicle fails to remote start or exits remote start prematurely: • remote start cancelled — door ajar • remote start cancelled — hood ajar • remote start cancelled — fuel low • remote start...

  • Page 47

    • ignition in off position for keyless enter-n-go™ vehicle • fuel level meets minimum requirement warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Carbon monoxide is poisonous and can cause seri...

  • Page 48

    To exit remote start mode without driving the vehicle push and release the remote start button one time or allow the engine to run for the entire 15-minute cycle. Note: to avoid unintentional shutdowns, the system will disable the one time push of the remote start button for two seconds after receiv...

  • Page 49

    Remote start windshield wiper de–icer activation — if equipped when remote start is active and the outside ambient temperature is less than 40° f (4.4° c), the windshield wiper de-icer will be enabled. Exiting remote start will resume previous operation, except if the windshield wiper de-icer is act...

  • Page 50

    Caution! (continued) • the sentry key® immobilizer system is not com- patible with some aftermarket remote starting sys- tems. Use of these systems may result in vehicle starting problems and loss of security protection. General information the sentry key® system complies with fcc rules part 15 and ...

  • Page 51

    To arm the system follow these steps to arm the vehicle security alarm: 1. Make sure the vehicles ignition is cycled to the stop/ off position (refer to #starting the engine# in #start- ing and operating# for further information). • for vehicles equipped with keyless enter-n-go™, make sure the vehic...

  • Page 52

    3. If any doors are open, close them. Note: • if a second chime is heard after approximately four seconds from arming the alarm, disarm the alarm by pushing the unlock button. Check for the correct closure of doors and liftgate, then reactivate the system by following steps 1 and 2. • if a second ch...

  • Page 53

    Note: • the driver’s door key cylinder cannot arm or disarm the vehicle security alarm. • when the vehicle security alarm is armed, the interior power door lock switches will not unlock the doors. The vehicle security alarm is designed to protect your vehicle. However, you can create conditions wher...

  • Page 54

    If the lock symbol is visible when the door is shut, the door will lock. Therefore, make sure the key fob is not inside the vehicle before closing the door. Note: the manual lock knob unlocks each individual door separately as well as the liftgate. Warning! • when leaving the vehicle, always remove ...

  • Page 55

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n-go™ in the mar/run mode. A child could operate power windows, other controls, or move the vehicle. • do not leave ...

  • Page 56

    Locking/unlocking from the inside push the lock button on the driver or passenger door trim panel to lock the doors. With the doors locked, push the unlock button to unlock the doors. The doors can also be locked and unlocked with the keyless enter-n-go™ (passive entry) system if equipped. For furth...

  • Page 57

    Keyless enter-n-go™ the passive entry system is an enhancement to the vehicle’s remote keyless entry (rke) system and a feature of keyless enter-n-go™. This feature allows you to lock and unlock the vehicle’s door(s) without having to push the rke transmitter lock or unlock buttons. Note: • passive ...

  • Page 58

    Note: if “unlock all doors 1st press” is programmed, all doors will unlock when you grab hold of the front driver’s door handle. To select between “unlock driver door 1st press” and “unlock all doors 1st press,” refer to “uconnect® settings” in “multimedia” for further infor- mation. To unlock from ...

  • Page 59

    Do not grab the door handle when pushing the door handle lock button. This could unlock the door(s). Note: the passive entry system will not operate if the rke transmitter battery is dead. The vehicle doors can also be locked by using the lock button located on the vehicle’s interior door panel. Pus...

  • Page 60

    Preventing inadvertent locking of passive entry rke transmitter in vehicle (fobik-safe) to minimize the possibility of unintentionally locking a passive entry rke transmitter inside your vehicle, the passive entry system is equipped with an automatic door unlock feature which will function if the ig...

  • Page 61

    Emergency unlocking driver door if the remote keyless entry (rke) transmitter battery is low or dead, the emergency key can be used to unlock the driver side door lock cylinder. To release the emergency key, proceed as follows: 1. Slide the emergency key release button to the side. 2. Remove the eme...

  • Page 62

    Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be severely injured or killed. Children should be warned not to touch the parking brake, brake peda...

  • Page 63

    Note: if “unlock all doors 1st press” is programmed in evic/did, if equipped, all doors will unlock when you push the electronic release. If #unlock driver door 1st press# is programmed in uconnect®, the liftgate will unlock when you push the electronic lock/unlock button on the liftgate. For furthe...

  • Page 64

    Child locks to provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a child-protection door lock system. To use the system, open each rear door, use a flat blade screwdriver (or ignition key) and rotate the dial to the lock or unlock position. Whe...

  • Page 65

    Note: • when the child lock system is engaged, the door can only be opened by using the outside door handle even though the inside door lock is in the unlocked position. • after disengaging the child-protection door lock system, always test the door from the inside to make certain it is in the desir...

  • Page 66

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 67

    Manual front seat forward/rearward adjustment on models equipped with manual seats, the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have reached the desired position....

  • Page 68

    Recline adjustment to adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired position and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Power adjustment (front) — if equipped the power seat controls are ...

  • Page 69

    Forward or rearward adjustment the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Height adjustment the height of the seats can be adjusted up ...

  • Page 70

    Heated seats — if equipped the heated seat switches are located on the instrument panel. You can choose between two heating levels: • push the heated seat button once to turn the hi setting on. • push the heated seat button a second time to turn the lo setting on. • push the heated seat button a thi...

  • Page 71

    Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially ...

  • Page 72

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. Removing shelf — if equipped proceed as follows: 1. Disconnect the two links that support the...

  • Page 73

    3. Clear the pins placed outside of the shelf, and then remove the rear shelf pulling it upwards. 4. The rear shelf can be stored in the cargo area, or behind the front seatbacks. Partial enlargement of cargo area enlargement of the left side of the cargo area allows you to carry a single passenger ...

  • Page 74

    Cargo area enlargement folding both sides of the rear seat provides additional storage in the rear cargo area. Proceed as follows: 1. Remove the rear shelf (if equipped). 2. Fully lower the rear seat head restraints. 3. Move the safety belts to the outboard side of the seat. 4. Pull the seatback rel...

  • Page 75

    Warning! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. Head restraints head restraints are de...

  • Page 76

    Front head restraints your vehicle is equipped with driver and passenger head restraints. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjust- ment button, located on the base of the head restraint, and push downward on the head restraint. To ...

  • Page 77

    Note: do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head. Warning! • a loose head restraint thrown forward in a colli- sion or hard stop could cause serious injury or death to occupants of the vehicle. Always ...

  • Page 78

    To reinstall the head restraint, put the head restraint posts into the holes and push downward. Then adjust it to the appropriate height. Note: do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head. Warning! • a ...

  • Page 79

    Steering wheel tilt/telescoping steering column this feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located below the steering wheel at the end of the steering column. Tilt/telescoping st...

  • Page 80

    To unlock the steering column, push the tilt/telescoping lever downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steeri...

  • Page 81

    Auto on comfort — if equipped if the external temperature is below 40 °f (4.4 °c) at each start-up of the vehicle the heated steering wheel func- tionality is turned on. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury,...

  • Page 82

    Note: the mirror will automatically release in the event of heavy contact with a passenger. Auto dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to...

  • Page 83

    Note: this feature is disabled when the vehicle is moving in reverse. Outside mirrors power adjustment mirrors the power mirror switch is located on the drivers door panel. To adjust the mirror, push the mirror adjustment switch in the four directions indicated by arrows. Note: • to adjust the power...

  • Page 84

    Folding mirror the exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The mirror has three detent positions: full forward, normal and full rearward. Power mirror switch 1 — mirror adjustment switch 2 — mirror selector switch folding exterior mirror 82 ...

  • Page 85

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster. Blind spot monitoring (bsm) — if equipped the blind spot monitoring (bsm) system uses two radar- based sensors, located inside the rear bumper fas...

  • Page 86

    The bsm detection zone covers approximately one lane width on both sides of the vehicle, 10 ft (3 m). The zone length starts at the outside mirror and extends approxi- mately 20 ft (6 m) beyond the rear bumper of the vehicle. The bsm system monitors the detection zones on both sides of the vehicle w...

  • Page 87

    The bsm system notifies the driver of objects in the detection zones by illuminating the bsm warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “modes of operation” for further information. The bsm system monitors the...

  • Page 88

    Entering from the side vehicles that move into your adjacent lanes from either side of the vehicle. Entering from the rear vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 31 mph (50 km/h). Side monitoring rear monitor...

  • Page 89

    Overtaking traffic if you pass another vehicle slowly with a relative speed less than 15 mph (25 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (25 km/h),...

  • Page 90

    The bsm system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. Overtaking/passing stationary objects 88 getti...

  • Page 91

    The bsm system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes. Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicy- clists, or ...

  • Page 92

    Rear cross path (rcp) the rear cross path (rcp) feature is intended to aid the driver when backing out of parking spaces where their vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed. The rcp system will th...

  • Page 93

    Note: in a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When rcp is on and the vehicle is in reverse, the driver is alerted using both the visua...

  • Page 94

    Blind spot alert lights/chime when operating in blind spot alert lights/chime mode, the bsm system will provide a visual alert in the appro- priate side view mirror based on a detected object. If the turn signal is then activated, and it corresponds to an alert present on that side of the vehicle, a...

  • Page 95

    Note: the rear bumper must be clean and free of any obstructing debris. System not available in the case of the system being temporary unavailable: • bsm mirror warning lights are turned on continu- ously. • a chime will turn on. • a instrument cluster message will display “blind spot monitoring tem...

  • Page 96

    Exterior lights headlights the headlight switch is located on the left side of the instrument panel. The headlight switch controls the operation of the headlights, side marker lights, daytime running lights, fog lights and the dimming of the instru- ment cluster and interior lighting. Turning on the...

  • Page 97

    Automatic lighting — if equipped light sensor the light sensor is equipped with an infrared led, located on the windshield. It detects changes in light intensity outside the vehicle, based on the sensitivity of light set by using the menu on the display or on the uconnect® system. The higher the sen...

  • Page 98

    Front fog lights — if equipped the front fog light switch is built into the headlight switch. To activate the front fog lights, turn on the parking lights or the low beam headlights and push the headlight switch. To turn off the front fog lights, push the headlight switch a second time or turn off t...

  • Page 99

    Headlight delay disable the feature is disabled by turning on the headlights, the parking lights or by placing the ignition in the mar/ run position. If you shut off the lights before the ignition is turned on, they will turn off in the normal manner. Note: the lights must be turned off within two m...

  • Page 100

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. When the daytime running lights are on and a turn signal is activated, the daytime running lamp will turn off on the sid...

  • Page 101

    Note: • before exiting the vehicle, make sure that the interior lights are turned off. This will prevent the battery from discharging once the doors are closed. • if a light is left on it will automatically be turned off after approximately 15 minutes after the ignition is in the stop/off position. ...

  • Page 102

    Timing exiting the vehicle the dome light will illuminate under the following conditions when the ignition is turned to the stop/off position and the key is removed: • the dome light will illuminate for 27 seconds after the key is removed from the ignition. • the opening of one of the doors (approxi...

  • Page 103

    Lower glove compartment light an interior light is located is the lower glove compart- ment. This light automatically turn on/off when the glove compartment is opened and closed, regardless of the position of the ignition. Note: in order to preserve the life of the battery, the light will turn off a...

  • Page 104

    Rear dome light — if equipped push the button on the rear dome light once to turn the light on, the light will remain on at all times. Push the button a second time to turn the light off, the lights will remain off until a door is opened. Vehicles with retractable roof for vehicles equipped with a r...

  • Page 105

    Cargo area lights an interior light is located on the left side panel in the cargo area. This light automatically turn on/off when the liftgate is opened and closed, regardless of the position of the ignition. Note: in order to preserve the life of the battery, the light will turn off after 15 minut...

  • Page 106

    Wipers and washers front wiper operation the windshield wiper/washer controls are located on the lever on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. Headlight switch 1 — ambient light control — if equipped 2 — instrumen...

  • Page 107

    Caution! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur. Windshield wiper operation rotate the wi...

  • Page 108

    Mist use this feature when weather conditions make occa- sional usage of the wipers necessary. Push the lever upward to the mist position and release for a single wiping cycle. Note: the mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The...

  • Page 109

    Wiper sensitivity. Setting two can be used if the driver desires more sensitivity. Place the wiper switch in the off position when not using the system. Note: • the rain sensing feature will not operate when the wiper switch is in the low or high-speed position. • the rain sensing feature may not fu...

  • Page 110

    Remote start mode inhibit — on vehicles equipped with remote starting system, rain sensing wipers are not operational when the vehicle is in the remote start mode. Once the operator is in the vehicle and has placed the ignition switch in the mar/run position, rain sensing wiper operation can resume,...

  • Page 111

    Rear window defroster the rear window defroster button is located with the climate controls on the instrument panel. Push this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns o...

  • Page 112

    • activation by rear defrost — the windshield wiper de-icer will be activated automatically when the rear defrost is turned on and the ambient temperature is below 40° f (4.4° c). • activation by remote start operation — when re- mote start is active and the outside ambient tempera- ture is less tha...

  • Page 113

    Center air outlets 1 — air flow outlet adjustment 2 — adjustable air outlet 3 — air vane adjustment right side air outlets 1 — fixed air outlet 2 — adjustable air outlet 3 — air vane adjustment 4 — air flow outlet adjustment 4 getting to know your vehicle 111.

  • Page 114

    Manual climate controls — if equipped the manual climate controls consist of a series of rotary dials with inner push buttons. 1. Blower control rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control clo...

  • Page 115

    • panel air is directed through the outlets in the instrument panel. These outlets can be ad- justed to direct airflow. Note: the center instrument panel outlets can be ad- justed so that they are directed toward the rear seat passengers for maximum airflow to the rear. • bi-level air is directed th...

  • Page 116

    4. Rear defrost button push and release the rear defrost control button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 20 minutes. 5. A/c but...

  • Page 117

    Rear window defrosting push and release the rear window defrost button to turn the function on/off. Activation of this function is indicated by the rear defrost indicator light on the instrument panel turning on. The function is automatically deactivated after 20 minutes. If equipped, push the rear ...

  • Page 118

    System maintenance in winter, the climate control system must be turned on at least once a month for approximately 10 minutes. Have the system inspected at an authorized dealership before the summer. Note: the system uses r-1234yf (refrigerant) which does not pollute the environment in the event of ...

  • Page 119

    1. Driver temperature control provides the driver with independent temperature con- trol. Rotate the adjustment knob to set desired tempera- ture shown in the temperature display. Rotate fully counter-clockwise for maximum a/c (lo). 2. A/c button push the a/c control button to change the current set...

  • Page 120

    6. Auto button pushing this button will automatically control the inte- rior cabin temperature by adjusting airflow distribution and amount. Performing this function will cause the automatic climate controls to change between manual mode and automatic modes. 7. Passenger temperature control provides...

  • Page 121

    10. Mode buttons airflow distribution modes can be adjusted so air comes from the instrument panel outlets, floor outlets, de-mist outlets and defrost outlets by selecting these buttons. One, two or all modes may be selected at any one time. 11. Blower control blower control is used to regulate the ...

  • Page 122

    Display, respectively. To deactivate these functions, turn the temperature knob to the desired temperature. Description the automatic dual zone climate control system regu- lates the air temperatures in the passenger compartment in two zones: driver side and passenger side. The system maintains comf...

  • Page 123

    The amount of air introduced into the passenger com- partment is not affected by car speed; it is regulated by the fan, which is controlled electronically. The air temperature is always automatically controlled according to the temperature set on the display (except for when the system is off or in ...

  • Page 124

    During automatic operation, you can change the set temperatures, air distribution and blower speed at any time by using the relevant buttons or knobs: the system will automatically change the settings to adjust to the new requirements. During automatic operation (auto), varying the air flow and/or d...

  • Page 125

    Air distribution selection by pushing the mode control buttons (defrost/panel/ floor buttons), it is possible to set one of the seven possible air distributions manually by activating one or more mode buttons: • defrost mode – air flow to the windshield and front side window diffusers to defrost the...

  • Page 126

    In auto mode, the climate control system automatically manages air distribution (leds on the mode control buttons are off). When set manually, the air distribution is indicated by the leds on the selected buttons turning on. In combined function mode, functions are enabled to- gether with those alre...

  • Page 127

    Auto button when the auto button is pushed (led illuminated), the climate control system automatically adjusts the follow- ing settings in the corresponding zones: • quantity and distribution of the air introduced into the passenger compartment. • climate control system compressor. • air recirculati...

  • Page 128

    Air recirculation the air recirculation is managed by the following: • forced activation (air recirculation always on): indi- cated by the led on the recirculation control button. • forced deactivation (air recirculation always off, air intake from the outside), signalled by the led on the recircula...

  • Page 129

    Climate control system compressor push the a/c control button to activate/deactivate the compressor (activation is indicated by the led on the button turning on). The system remembers that the compressor has been turned off, even after the engine has stopped. Pushing the a/c button will stop auto mo...

  • Page 130

    Rapid window demisting (max-defrost function) push the max-defrost button to activate (led on) the windshield and side window demisting function. The climate control system carries out the following operations: • turns on the air conditioning compressor when envi- ronmental conditions are suitable. ...

  • Page 131

    Rear window defrosting push and release the rear window defrost button to turn the function on/off. Activation of this function is indicated by the rear defrost indicator light on the instrument panel turning on. The function is automatically deactivated after 20 minutes. If equipped, push the rear ...

  • Page 132

    • blower increase • auto to restart the climate control system in fully automatic mode, push the auto button. System maintenance in winter, the climate control system must be turned on at least once a month for approximately 10 minutes. Have the system inspected at an authorized dealership before th...

  • Page 133

    There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate only when the ignition is in the mar/run or avv/start position. Note: for vehicles equipped with uconnect®, the power window switches will remain active for ...

  • Page 134

    Warning! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n- go™ in the mar/run mode. Occupan...

  • Page 135

    The driver and passenger power window switches have an auto-down feature. Push the switch for half a second and release it; the window will go down auto- matically. To partially open the window, push the window switch and release it when you want the window to stop. To stop the window from going all...

  • Page 136

    To partially close the window, lift the window switch and release it when you want the window to stop. Note: • if the window runs into any obstacle during auto- closure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window. • any im...

  • Page 137

    Power sunroof — if equipped the sunroof has two glass panels (the front one is operational and the rear one fixed) and is equipped with two manual operated sun blinds, front and rear. The power sunroof can be operated only with the ignition key turned to the mar/run position. The power sunroof switc...

  • Page 138

    Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle or in a location accessible to children. Occupants, particularly unattended children, can become entrapped by the power sun- roof while operating the power sunroo...

  • Page 139

    Note: during the open/close or vent operation any push on the switches will stop the closing of the panel. Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, o...

  • Page 140

    Caution! • when refitting sunroof, be careful to avoid fingers, scarves, ties and items of clothing from getting caught under the panel. • do not open the roof in the presence of snow or ice. There is risk of damage. Power sunroof relearn procedure as a result of any abnormal behavior of the roof or...

  • Page 141

    3. Bring the ignition to the position mar/run. 4. Pull the open/close button and hold it for at least 10 seconds, after which you should feel the mechanical stop of the electric motor of the roof. 5. Within 5 seconds, pull to close and hold the open/ close button, the roof makes a complete cycle of ...

  • Page 142

    3. Push the safety latch release lever toward the passen- ger side of the vehicle. The safety latch is located behind the center front edge of the hood. 4. Remove the support rod from the locking tab and insert it into the seat located on the underside of the hood. Safety latch location hood prop sy...

  • Page 143

    Note: • before lifting the hood, check that the wiper arms are not in motion and not in the lifted position. • while lifting the hood, use both hands. • vehicle must be at a stop and the automatic transmis- sion must be in park. Manual transmission vehicles must have the electric park brake engaged....

  • Page 144

    Liftgate the liftgate release function is disabled when the vehicle is in motion. Opening opening from outside to unlock the liftgate from the outside, squeeze the electronic liftgate release and pull the liftgate open with one fluid motion. When opening the door, the turn signal lights will flash t...

  • Page 145

    Internal emergency release proceed as follows: 1. Lower the headrests and tilt the seatbacks. 2. Using the supplied screwdriver (located under cargo floor in tool kit), remove the yellow tab. 3. Insert the screwdriver into the release tab slot to trigger the release tab of the liftgate. 1 — yellow t...

  • Page 146

    Closing grasp the liftgate closing handle and lower the liftgate. Note: before closing the liftgate, make sure to be in possession of the key because the liftgate will be locked automatically. Cargo area features cargo load floor the vehicle is equipped with a load floor that can be adjusted as need...

  • Page 147

    Position 2 (elevated position): when the rear seatbacks and front passenger seat is folded flat, it will allow for loading objects of long dimensions. It is recommended to use this position only during the actual transporting of the objects, then bring the load floor in position 1. Note: with a full...

  • Page 148

    Caution! The load floor must be arranged in a central position with respect to cargo area. Displacement load floor to position the load from the lower to the upper position, proceed as follows: 1. Grasp the load floor handle and lift up the load floor. 2. Correctly place the load floor on the side p...

  • Page 149

    Anchoring of the load the cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. Cargo box — if equipped the cargo area contains a preformed cargo box that can be used for the storage of objects that allows you to obtain a uniform level wh...

  • Page 150

    Note: the cargo box is sized for a maximum capacity of distributed weight equal to 242 lbs (110 kg). Internal equipment glove compartments the glove compartments is located on the passengers side of the instrument panel. Upper glove compartment to open the upper compartment, push in the button locat...

  • Page 151

    Lower glove compartment to open the lower glove compartment, pull outward on the latch and lower the glove compartment door. Once the glove compartment is open, a light will turn on to illuminate the compartment. Note: • do not insert objects in the glove compartments that will not allow the compart...

  • Page 152

    The visors also have illuminated vanity mirrors to allow use in low light conditions. Lift upward on the mirror cover to access the mirror. Extendible sun visor to extend the sun visor, proceed as follows: 1. Place the sun visor against the door glass by detaching it from the hook and turning it tow...

  • Page 153

    Power outlets the front power outlet is located under the center stack of the instrument panel. It only operates with the ignition in the mar/run position. Note: the power outlet can be changed to “battery” powered all the time by switching the power outlet engine compartment fuses/distribution unit...

  • Page 154

    Models equipped with the optional #smoker kit,# will have a cigar lighter instead of the power outlet. Caution! Do not connect devices with power higher than 180 watts (15 amps) to the socket. Do not damage the socket by using unsuitable adaptors. If the 180 watt (15 amp) power rating is exceeded th...

  • Page 155

    Caution! (continued) • accessories that draw higher power (i.E., coolers, vacuum cleaners, lights, etc.) will degrade the bat- tery even more quickly. Only use these intermit- tently and with greater caution. • after the use of high power draw accessories, or long periods of the vehicle not being st...

  • Page 156

    Warning! When the cigar lighter is in use it becomes very hot. To avoid serious injury, handle the cigar lighter with care. Always check that the cigar lighter has turned off. Caution! Do not connect devices with power higher than 180 watts (15 amps) to the socket. Do not damage the socket by using ...

  • Page 157

    Front armrest the front armrest is located between the front seats. The armrest can be adjusted by moving it in the direction indicated by the arrows. Push the storage handle and lift up the armrest to access the storage compartment. Front armrest handle storage compartment 4 getting to know your ve...

  • Page 158

    Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Cupholders there are two cupholders for the front seat passengers, located in the center console. Front cupholders 156 gettin...

  • Page 159

    Grab handles the grab handles are located immediately above the doors. The rear handles are equipped with hooks for dress hangers. Roof luggage rack — if equipped your vehicle may be equipped with a roof luggage rack for transporting accessories. Crossbars should always be used whenever cargo is pla...

  • Page 160

    Do not use the sunroof when using the crossbars. Caution! • to avoid damage to the roof luggage rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as possible and secure the load appropriately. • long loads, which extend over the windshield, ...

  • Page 161: Contents

    Getting to know your instrument cluster contents ! Instrument cluster . . . . . . . . . . . . . . . . .160 ! Onboard diagnostic system (obd ii) . . .162 ! Electronic vehicle information center (evic) . . . . . . . . . . . . . . . . . . . . . . . .163 ▫ evic description. . . . . . . . . . . . . . . ....

  • Page 162

    Instrument cluster 160 getting to know your instrument cluster.

  • Page 163

    1. Speedometer • indicates the speed of the car 2. Fuel level gauge • the fuel gauge in the evic indicates the amount of fuel left in the tank. • the light comes on, together with a chime and the display of a message in the evic, when the gas tank has 1.5 to 2 gallons (5 to 7 liters) of fuel remaini...

  • Page 164

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 165

    Electronic vehicle information center (evic) evic description the vehicle can be equipped with multifunctional dis- play (evic) which offers useful information to the driver. With the ignition in the stop/off position (and the key removed, for vehicles with mechanical key), opening/ closing of a doo...

  • Page 166

    The display shows the following information, if equipped: • zone (1) – date (centered) – compass (centered) – time (centered) – external temp. (centered) • zone (2) – actual gear indication (centered) – prnd (centered) • zone (3) – date (centered) – compass (centered) – time (centered) – external te...

  • Page 167

    • zone (5) – trip and fuel label (left) – trip and fuel units (left) – trip and fuel value (right) – trip and fuel progress bar (centered) – text (left) • zone (6) – odometer digits (left) – odometer unit (right) – cruise control speed set (center) – speed buzzer (right) • red telltales (left) • amb...

  • Page 168

    • up arrow button push and release the up arrow button to scroll upward through the main menu and submenus. • down arrow button push and release the down arrow button to scroll downward through the main menu and submenus. • right arrow button push and release the right arrow button to access the inf...

  • Page 169

    Unless reset, this message will continue to display each time you turn the ignition switch to the mar/run position. To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure. 1. Turn the ignition switch to the mar/run position. (do not st...

  • Page 170

    Evic menu/submenu items the menu is composed of the following items: • trip – speedometer – instantaneous info – trip a – trip b – best consumption • drive mode selector – auto mode – sport mode – traction/all weather mode • vehicle info – tire pressure – oil temperature – battery voltage • driver a...

  • Page 171

    Trip this evic menu item allows you to view and select information about the #trip computer#: • speedometer – view and change the speedometer scale from mph to km/h (km/h to mph). • instantaneous info – view and change the distance (miles or km) – view and change the instantaneous consumption (mpg, ...

  • Page 172

    Drive mode selector this evic menu/submenu items allows you to view and select information about the #drive mode#: • auto mode – drive style – instantaneous consumption – auto mode description • sport mode – acceleration – turbo boost or engine torque – sport mode description • traction/all weather ...

  • Page 173

    Driver assist this menu item allows you to change the settings (#no- tice lanesense# and #intensity lanesense#) relating to the lanesense system (if equipped). • notice lanesense • by selecting this function, you can select the #readi- ness# of lanesense, choosing between the options # near,# #mediu...

  • Page 174

    The background color of the display varies according to the priorities of the failure: • failed messages with low priority displays in yellow • failed messages with high priority displays in red settings this menu item allows you to change the settings for the following: • display • units • clock an...

  • Page 175

    • phone repetition: the instrument cluster display can also display the information concerning phone mode. The information that can be displayed is the connec- tion status of the mobile phone (phone connected or disconnected), the active telephone calls/incoming/on hold, and the management of double...

  • Page 176

    Security by selecting the item “security,” you can make the following adjustments: • speed warning: set the vehicle speed limit (mph or km/h), which the driver is notified through a visual and acoustic signaling (display of a message and a symbol on the display). • seat belt buzzer: this function is...

  • Page 177

    • auto park brake — if equipped: enable/disable auto- insertion of the electric parking brake lights by selecting the item #lights,# you can make the follow- ing adjustments: • headlight off delay: set the delay for headlight shut- off after engine shutoff • headlight sensor: adjust the sensitivity ...

  • Page 178

    • horn with remote start: activate/deactivate the horn at the remote starting of the engine with the rke. • unlock on first press of key fob (vehicles without passive entry): allows you to choose whether to un- lock all the doors or only the driver’s side door on the first push of the unlock button ...

  • Page 179

    Quantities displayed distance travelled indicates the distance travelled by the start of the new trip. Average consumption represents the average fuel consumption since the start of the new trip. Travel time elapsed time since the start of the new trip. Ok button short push of the button: display of...

  • Page 180

    Warning lights and messages the evic display consists of three sections: 1. The reconfigurable top line where compass, direction, and outside temperature are displayed. • right side default to ignition status for those with push button ignition. 2. The main display area where the menus and pop up me...

  • Page 181

    • unstored messages this message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are #turn signal on# (if a turn signal is left on) and #lights on# (if driver leaves the vehicle). • unstored messages until run these messages ...

  • Page 182

    Electric park brake (epb) engaged • what does it mean the light comes on with electric park brake (epb) engaged. • what to do switch off the epb and check that the indicator light goes off. If the light remains on, see an authorized dealer. Electronic brake force distribution (ebd) failure • what do...

  • Page 183

    Air bag • what does it mean by placing the ignition switch in mar/ run, the indicator light illuminates but should go out after a few seconds. If the indicator illuminates, this indicates a fail- ure of the air bag system. The dedicated message shows in the display. For more details, refer to #occup...

  • Page 184

    Seat belt reminder • what does it mean the light comes on as a steady light with the car stopped as a seat belt reminder. • what to do for the permanent deactivation of the horn (buzzer) system s. B. R. (seat belt reminder), contact your authorized dealer. It is possible to reactivate the system thr...

  • Page 185

    In the case of heavy use of the car (e.G. In terms of performance): slow down and, if the light stays on, stop the car. For two or three minutes, keep the engine running and slightly accelerate to help the flow of coolant in the system. Then, turn the engine off. Check for the correct level of coola...

  • Page 186

    Tpms failure • what does it mean each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recom- mended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (if your vehicle has tires of a different size ...

  • Page 187

    As the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. Tpms malfunctions may occur for a variety of rea- sons, including the installation of replacement or alternate tires or wheels on the vehicle that p...

  • Page 188

    Esc system • what does it mean intervention esc system: the light will start to flash as soon as the tires lose traction and the esc system becomes ac- tive. If the “esc activation/malfunction indicator light” begins to flash during ac- celeration, ease up on the accelerator and apply as little thro...

  • Page 189

    Engine malfunction • what does it mean the light is an integral part of the diagnostic system of the vehicle, called obd ii. This system monitors the performance of the emis- sions, engine, and automatic transmission control systems. The light comes on briefly (as a bulb check) when the ignition is ...

  • Page 190

    Park/headlight on indicator • what does it mean the light comes on by activating the park- ing lights or headlights. This feature allows you to maintain the lights for a period of 30, 60, or 90 seconds after placing the ignition in the stop posi- tion. In some conditions, such as the poor quality of...

  • Page 191

    Headlights on • what does it mean the indicator light comes on by turning on the headlights. Cruise set indicator — if equipped • what does it mean this light will turn on when the electronic speed control is set. Glow plug icon • what does it mean this icon blinking indicates that the engine cranki...

  • Page 192

    Air bag warning light • what does it mean illumination of the air bag warning light indicates a failure of the air bag system when the ignition switch is placed in the mar/run position. The display shows the message dedicated. • what to do if the light is either not on during starting, stays on, or ...

  • Page 193

    Hood open warning light • what does it mean the light will illuminate when the engine hood is not completely closed. With the hood open and the vehicle in motion, a chime will sound. • what to do properly close the hood. Liftgate open warning light • what does it mean this light will illuminate when...

  • Page 194

    If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough idle or en- gine stall, and your vehicle may require towing. Automatic transmission failure • what does it mean this light will illuminate when the system det...

  • Page 195

    Sentry key® / vehicle security alarm system failure • what does it mean system failure sentry key® after placing the ignition to the mar/ run position, if there is a problem with the system, the vehicle security light will illuminate. This condition will result in the engine being shut off after two...

  • Page 196

    Light sensor failure • what does it mean the light illuminates in a the light sensor failure. • what to do please contact an authorized dealer. Exterior light failure • what does it mean this light illuminates to indicate a failure of any of the following lights: 1. Daytime running lights (drl) 2. P...

  • Page 197

    Keyless enter-n-go™ system failure • what does it mean the light illuminates in case of failure of the keyless enter-n-go™. • what to do please contact an authorized dealer. Enhanced accident response system failure • what does it mean the light illuminates in case of failure of the enhanced acciden...

  • Page 198

    Loose fuel filler cap/flapper message indicator • what does it mean this light will illuminate when fuel filler cap is loose. For capless fuel systems, the fuel flapper or the door are not closed properly. • what to do properly close the filler cap. For capless fuel systems, ensure the fuel flapper ...

  • Page 199

    Power steering system warning • what does it mean this light will illuminate to indicate a fail- ure in the electronic power steering system (eps). Although it will still be possible to steer the car, additional effort may be needed to operate the steering wheel. • what to do please contact an autho...

  • Page 201: Safety

    Safety contents ! Brake system . . . . . . . . . . . . . . . . . . . . . . .201 ! Electronic brake control system . . . .202 ▫ electronic brake force distribution (ebd) . . . .202 ▫ brake system warning light. . . . . . . . . . . . . .202 ▫ anti-lock brake system (abs) . . . . . . . . . . . .202 ▫ a...

  • Page 202

    ! Safety tips . . . . . . . . . . . . . . . . . . . . . . . . .270 ▫ transporting passengers . . . . . . . . . . . . . . . . .270 ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . .271 ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 203

    Brake system your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still function. However, there will be some loss of overall braking effectiveness. This will be evident by increased pedal travel during ...

  • Page 204

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system (ebc). This system includes elec- tronic brake force distribution (ebd), anti-lock brake system (abs), brake assist system (bas), hill start assist (hsa), traction control system (tcs), electron...

  • Page 205

    The abs performs a self-check cycle to ensure that the abs is working properly each time the vehicle is started and driven. During this self-check you may hear a slight clicking sound as well as some related motor noises. Abs is activated during braking when the system detects one or more wheels beg...

  • Page 206

    Warning! (continued) • the abs cannot prevent the natural laws of phys- ics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • the abs cannot prevent collisions, including th...

  • Page 207

    Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce...

  • Page 208

    Hill start assist (hsa) the hsa system is designed to mitigate roll back from a complete stop while on an incline. If the driver releases the brake while stopped on an incline, hsa will continue to hold the brake pressure for a short period. If the driver does not apply the throttle before this time...

  • Page 209

    Warning! (continued) brake operation to ensure safe operation of the vehicle under all road conditions. Your complete attention is always required while driving to maintain safe control of your vehicle. Failure to follow these warnings can result in a collision or serious personal injury. Disabling ...

  • Page 210

    8. Turn the ignition switch to the off position and then back to the on position. If the sequence was com- pleted properly, the “esc off indicator light” will blink several times to confirm hsa is disabled. 9. Repeat these steps if you want to return this feature to its previous setting. Traction co...

  • Page 211

    Esc uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match the intended path, esc applies the brake of the appro- priate wheel to assist in counteracting the oversteer or understeer condi...

  • Page 212

    Warning! Electronic stability control (esc) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slipper...

  • Page 213

    Warning! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur. Erm cannot prevent all wheel lift or roll overs, especially those that involve leaving the roadway or striking objects or other vehicles. The capabili...

  • Page 214

    Occupant restraint systems some of the most important safety features in your vehicle are the restraint systems: • seat belt systems • supplemental restraint systems (srs) air bags • child restraints important safety precautions please pay close attention to the information in this section. It tells...

  • Page 215

    6. All occupants should always wear their lap and shoulder belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the advanced front air bags room to inflate. 8. Do not lean against the door or window. If your vehicle has side air bags, and deployme...

  • Page 216

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 217

    Beltalert warning sequence the beltalert warning sequence is activated when the vehicle is moving above a specified vehicle speed range and the driver or outboard front seat passenger is un- buckled (the outboard front passenger seat beltalert is not active when the outboard front passenger seat is ...

  • Page 218

    Note: if beltalert has been deactivated and the driver or outboard front seat passenger is unbelted the seat belt reminder light will turn on and remain on until the driver and outboard front seat passenger seat belts are buckled. Lap/shoulder belts all seating positions in your vehicle are equipped...

  • Page 219

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. • wearing your seat belt incorrectly could make your injuries in a collision much worse. You ...

  • Page 220

    Warning! (continued) • a seat belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • a seat belt that is worn under your arm is danger- ous. Your body could strike the inside surfaces...

  • Page 221

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the sea...

  • Page 222

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 223

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the belt, push the red button on the buckle. The seat belt will automatically ret...

  • Page 224

    3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted. Adjustable upper shoulder belt anchorage in the driver and...

  • Page 225

    Note: the adjustable upper shoulder belt anchorage is equipped with an easy up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- ton. To verify the shoulder belt anchorage is latched, pull downward on the shou...

  • Page 226

    2. Grasp the mini-latch plate and pull the seat belt over the seat. 3. Route the shoulder belt to the inside of the left head restraint. 4. When the seat belt is long enough to fit, insert the mini-latch plate into the mini-buckle until you hear a “click.” pulling out the latch plate inserting latch...

  • Page 227

    5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. 6. When the seat belt is long enough to fit, insert the mini-latch plate into the mini-buckle until you hear a “click.” 7. Position the lap belt so that it is snug and ...

  • Page 228

    Warning! (continued) • when reattaching the mini-latch plate and mini- buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding procedure to detach the mini-latch plate and mini- buckle, untwist the webbing, and reattach the mini-latch plate and mini-buckl...

  • Page 229

    Keep the lap part of the seat belt low so that it does not come across the abdomen. Place the lap belt so that it will interact with the strong bones of the hips, which will take the force if there is a collision. Seat belt pretensioner the front seat belt system is equipped with pretensioning devic...

  • Page 230

    Switchable automatic locking retractor (alr) — if equipped the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) which is used to secure a child restraint system. For additional information, refer to “installing child restraints using the ...

  • Page 231

    If the passenger seating position is equipped with an alr and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt r...

  • Page 232

    How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the seat belt assembly must be replaced if the switchable automati...

  • Page 233

    Supplemental restraint system (srs) air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • knee impact bolsters • advanced front air bags • sup...

  • Page 234

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 235

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 236

    Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away f...

  • Page 237

    Supplemental driver knee air bag this vehicle is equipped with a supplemental driver knee air bag mounted in the instrument panel below the steering column. The supplemental driver knee air bag provides enhanced protection during a frontal impact by working together with the seat belts, pretensioner...

  • Page 238

    When the sab deploys, it opens the seam on the out- board side of the seatback’s trim cover. The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not ...

  • Page 239

    Sabics may help reduce the risk of head or other injuries to front and rear seat outboard occupants in certain side impacts and/or vehicle rollover events, in addition to the injury reduction potential provided by the seat belts and body structure. The sabics deploy downward, covering the side win- ...

  • Page 240

    Warning! • your vehicle is equipped with left and right supplemental side air bag inflatable curtains (sabics). Do not stack luggage or other cargo up high enough to block the deployment of the sabics. The trim covering above the side win- dows where the sabic and its deployment path are located sho...

  • Page 241

    Seat belts (and child restraints where appropriate) are necessary for your protection in all collisions. They also help keep you in position, away from inflating side air bags. To get the best protection from the side air bags, occupants must wear their seat belts properly and sit upright with their...

  • Page 242

    Side impacts in side impacts, the side impact sensors aid the orc in determining the appropriate response to impact events. The system is calibrated to deploy the side air bags on the impact side of the vehicle during impacts that require side air bag occupant protection. In side impacts, the side a...

  • Page 243

    If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or al...

  • Page 244

    Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the seat belt retractor assemblies replaced by an authorized dealer imme- diately. Also, have the occupant restraint controller system serviced as well. Not...

  • Page 245

    Enhanced accident response system reset procedure after the event occurs, when the system is active, a message regarding fuel cutoff is displayed. Turn the ignition switch from ignition avv/start or mar/ acc/on/run to ignition stop/off/lock. Care- fully check the vehicle for fuel leaks in the engine...

  • Page 246

    Customer action customer will see 6. Turn left turn signal switch on. Left turn light is on solid. Right turn light is on solid. 7. Turn left turn signal switch off. (turn signal switch must be placed in neutral state). Left turn light is off. Right turn light is off. 8. Turn ignition off. 9. Turn h...

  • Page 247

    The mar/acc/on/run position. After the self-check, the air bag warning light will turn off. If the orc detects a malfunction in any part of the system, it turns on the air bag warning light, either momentarily or continuously. A single chime will sound to alert you if the light comes on again after ...

  • Page 248

    Redundant air bag warning light if a fault with the air bag warning light is detected, which could affect the supplemental restraint system (“srs”), the redundant air bag warn- ing light will illuminate on the instrument panel. The redundant air bag warning light will stay on until the fault is clea...

  • Page 249

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion,...

  • Page 250

    These data can help provide a better understanding of the circumstances in which crashes and injuries occur. Note: edr data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the edr under normal driving conditions and no per- sonal data (e.G., name, g...

  • Page 251

    Warning! In a collision, an unrestrained child can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in you...

  • Page 252

    Summary of recommendations for restraining children in vehicles child size, height, weight or age recommended type of child restraint infants and toddlers children who are two years old or younger and who have not reached the height or weight limits of their child restraint either an infant carrier ...

  • Page 253

    Infants and child restraints safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and conv...

  • Page 254

    Older children and child restraints children who are two years old or who have outgrown their rear-facing convertible child seat can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who are over two years...

  • Page 255

    Warning! (continued) • when your child restraint is not in use, secure it in the vehicle with the seat belt or latch anchor- ages, or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or accident, it could strike the occupants or seatbacks and cause serious personal ...

  • Page 256

    If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check seat belt fit periodically and make sure the seat belt buckle is latched. A child’s squirming or slouching can move the belt out of p...

  • Page 257

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 258

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 259

    Latch positions for installing child restraints in this vehicle • — lower anchorage symbol 2 anchorages per seating position • — top tether anchorage symbol 6 safety 257.

  • Page 260

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 261

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 262

    Locating latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if...

  • Page 263

    Locating tether anchorages there are tether strap anchorages behind each rear seatback, near the floor. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighte...

  • Page 264

    Center seat latch: warning! • do not install a child restraint in the center posi- tion using the latch system. This position is not approved for installing child seats using the latch attachments. You must use the seat belt and tether anchor to install a child seat in the center seating position. •...

  • Page 265

    3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 266

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 267

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor • = top tether anchorage symbol 6 safety 265.

  • Page 268

    What is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint, ...

  • Page 269

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 270

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 271

    1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another p...

  • Page 272

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 273

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 274

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 275

    Floor mat safety information always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in o...

  • Page 276

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. C...

  • Page 277: Starting And Operating

    Starting and operating contents ! Starting the engine . . . . . . . . . . . . . . . .279 ▫ tip start feature . . . . . . . . . . . . . . . . . . . . . .280 ▫ if engine fails to start . . . . . . . . . . . . . . . . .280 ▫ cold weather operation . . . . . . . . . . . . . . . .282 ▫ extended park star...

  • Page 278

    ▫ key ignition park interlock. . . . . . . . . . . . . . .308 ▫ brake/transmission shift interlock system. . . .308 ! Speed control — if equipped . . . . . . . . .309 ▫ activation. . . . . . . . . . . . . . . . . . . . . . . . . . .310 ▫ setting a desired speed . . . . . . . . . . . . . . . . .310 ▫...

  • Page 279

    ▫ enabling and disabling parksense® . . . . . . . .326 ▫ service the rear park assist system . . . . . . . .327 ▫ park assist system usage precautions . . . . . . .328 ! Lanesense — if equipped . . . . . . . . . . . . .330 ▫ lanesense operation . . . . . . . . . . . . . . . . . . .330 ▫ turning lane...

  • Page 280

    ! Driving on slippery surfaces . . . . . . . . .356 ▫ acceleration . . . . . . . . . . . . . . . . . . . . . . . . .356 ▫ traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .356 ! Driving through water . . . . . . . . . . . . .357 ▫ flowing/rising water . . . . . . . . . . . . . . . . . ...

  • Page 281

    Starting the engine before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allo...

  • Page 282

    3. Cycle the ignition to the avv/start position and release it as soon as the engine is started. 4. If the engine does not start, place the ignition in the stop/off position and wait 10-15 seconds before attempting to restart the engine. Automatic transmission proceed as follows: 1. Set the electric...

  • Page 283

    Floor and hold it there. Crank the engine for no more than 15 seconds. This should clear any excess fuel in case the engine is flooded. Leave the ignition key in the mar/ run position, release the accelerator pedal and repeat the “normal starting” procedure. Caution! To prevent damage to the starter...

  • Page 284

    Cold weather operation to ensure reliable starting under extreme cold conditions an externally powered electric block heater (available from your authorized dealer) is required for the 1.4l turbo engine below -20°f (-29°c) and for the 2.4l engine below -29°f (-34°c) and is recommended for the 2.4l e...

  • Page 285

    Caution! To prevent damage to the starter, do not continuously crank the engine for more than 10 seconds at a time. Wait 10 to 15 seconds before trying again. After starting — warming up the engine proceed as follows: • travel slowly, letting the engine run at a reduced rpm, without accelerating sud...

  • Page 286

    Vehicles equipped with electronic key (keyless enter-n-go™): to shut off the engine with vehicle speed greater than 5 mph (8 km/h) you must push and hold the ignition or push the start/stop button three times consecutively within a few seconds. The engine will shut down and the ignition will be plac...

  • Page 287

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 288

    Electric park brake (epb) your vehicle is equipped with an electric park brake system (epb) that offers simple operation, and some additional features that make the parking brake more convenient and useful. The parking brake is primarily intended to prevent the vehicle from rolling while parked. Bef...

  • Page 289

    Switch will illuminate. If your foot is on the brake pedal while you apply the epb, you may notice a small amount of brake pedal movement. The epb can be applied even when the ignition switch is in the stop/off position but the brake warning lamp will not illuminate, how- ever, it can only be releas...

  • Page 290

    Note: • when parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. Apply the epb before placing the shift lever in park, otherwise the load on the transmission locking mechanism may make it difficult to move the shi...

  • Page 291

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave a vehicle equipped with keyless enter-n-go™ in the mar/run mode. A child could operate power win- dows, other controls, or move the vehicle. • be sure the parking brake i...

  • Page 292

    Warning! Driving the vehicle with the parking brake engaged, or repeated use of the parking brake to slow the vehicle may cause serious damage to the brake sys- tem; failure to do so can lead to brake failure and a collision. In the unlikely event of a malfunction of the epb system, a yellow epb fau...

  • Page 293

    Safehold safehold is a safety feature of the epb system that will engage the park brake automatically if the vehicle is left unsecured while the ignition switch is in mar/run. For automatic transmissions, the epb will automatically engage if all of the following conditions are met: • vehicle speed i...

  • Page 294

    Brake service mode we recommend having your brakes serviced by your authorized dealer. You should only make repairs for which you have the knowledge and the right equipment. You should only enter brake service mode during brake service. When servicing your rear brakes, it may be necessary for you or...

  • Page 295

    When brake service work is complete, the following steps must be followed to reset the parking brake system to normal operation: • ensure the vehicle is at a standstill. • press the brake pedal with moderate force. • apply the epb switch. Note: a dedicated message will appear in the evic if brake se...

  • Page 296

    To shift the gears, press the clutch pedal to the floor and put the shift lever to the desired position (the diagram for the engagement of the gears is displayed on the handle of the lever). To engage reverse gear from the neutral position lift the reverse ring, located below the knob and simultane-...

  • Page 297

    Manual transmission shift speeds in mph (km/h) all engines gear selection 2 to 3 3 to 4 4 to 5 5 to 6 accel. 24 (39) 34 (55) 47 (76) 56 (90) cruise 19 (31) 27 (43) 37 (60) 41 (66) downshifting moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hill...

  • Page 298

    Caution! (continued) • when descending a hill, be very careful to downshift one gear at a time to prevent overspeeding the engine which can cause engine damage, and/or clutch dam- age, even if the clutch pedal is pressed. If transfer case is in low range the vehicle speeds to cause engine and clutch...

  • Page 299

    Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage to the clutch and the transmission can result from skipping a gear while downshifti...

  • Page 300

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine stop/off, ...

  • Page 301

    Caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into or out of park or reverse only after the vehicle has come to a complete stop. • do not shift between park, reverse, neu- tral, or drive when the engine is above idle speed. • before shifting i...

  • Page 302

    The transmission gear range (prnd) is displayed both beside the shift lever and in the electronic vehicle infor- mation center (evic). To select a gear range, press the shift lever lock button on the shift lever and move the lever rearward or forward. You must also press the brake pedal to shift the...

  • Page 303

    Do not race the engine when shifting from park or neutral into another gear range. Caution! After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Gear ranges park (p) this range supplements the el...

  • Page 304

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 305

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the stop/off position to the mar/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear...

  • Page 306

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 307

    If the transmission temperature exceeds normal operat- ing limits, the transmission controller may modify the transmission shift schedule, reduce engine torque, and/or expand the range of torque converter clutch engagement. This is done to prevent transmission dam- age due to overheating. If the tra...

  • Page 308

    Note: in autostick mode, the transmission will only shift up or down when the driver moves the shift lever rearward (+) or forward (-), except as described below. • the transmission will automatically upshift when nec- essary to prevent engine over-speed. • the transmission will automatically downsh...

  • Page 309

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Transmission limp home mode transmission function is electronically monitored for abnormal conditions. If a condit...

  • Page 310

    Key ignition park interlock vehicles equipped with keyless enter-n-go™: this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition can be turned to the stop/off position. Also, the transmission is locked in park when- ever the igni...

  • Page 311

    Speed control — if equipped when engaged, the speed control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The speed control buttons are located on the right side of the steering wheel. Speed control buttons 1 — on/off 4 — set-/decel 2 — set+/accel 5 — cancel 3 — resume 7...

  • Page 312

    Note: in order to ensure proper operation, the speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the speed control system can be reactivated by pushing the speed control on/off button and resetting the desired vehic...

  • Page 313

    Deactivation a soft tap on the brake pedal, pushing the cancel button, esc intervention, forward collision mitigation, electronic park brake intervention, or normal brake pressure while slowing the vehicle will deactivate the speed control without erasing the set speed from memory. Pushing the on/of...

  • Page 314

    Metric speed (km/h) • pushing the set + button once will result in a 1 km/h increase in set speed. Each subsequent tap of the button results in an increase of 1 km/h. • if the button is continually pushed, the set speed will continue to increase until the button is released, then the new set speed w...

  • Page 315

    Accelerating for passing push the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. All wheel drive (awd) — if equipped this feature provides on-demand all-wheel drive (awd). The system is automatic with no driver inputs or additional driving sk...

  • Page 316

    Dynamic selector — if equipped the dynamic selector combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance in all driving conditions. The dynamic selector consists of the following positions: auto mode – this mode is designed for comfort an...

  • Page 317

    Warning messages in the event of a system fault, the system automatically defaults to #auto# mode and a message will appear in the evic display. Refer to “electronic vehicle information center (evic)” in “getting to know your instrument cluster” for further information. Forward collision warning (fc...

  • Page 318

    Vehicles with a manual transmission : after the end of the intervention of automatic braking, the engine could stall, unless the driver can depress the clutch pedal. Vehicles with automatic transmission : after the end of the intervention of automatic braking, the transmission may remain in last gea...

  • Page 319

    Note: • the minimum speed for fcw activation is 4 mph (7 km/h). • the maximum speed for fcw activation is 124 mph (200 km/h). • the fcw alerts may be triggered on objects other than vehicles such as guard rails or sign posts based on the course prediction. This is expected and is a part of normal fc...

  • Page 320

    • changing the fcw status to “off” deactivates the system, so no warning or active braking will be available in case of a possible collision • changing the fcw status to “only warning” prevents the system from providing limited active braking, or additional brake support if the driver is not braking...

  • Page 321

    By changing the option to #near#, the system will warn the driver of a possible accident with the vehicle ahead of it when the latter is a reduced distance. This setting offers a reaction time to the driver lower than the settings # medium# and #far#, in the case of a potential accident, while a mor...

  • Page 322

    The “fcw unavailable wipe front radar sensor” mes- sage can sometimes be displayed while driving in highly reflective areas (i.E. Tunnels with reflective tiles, or ice and snow). The system will recover after the vehicle has left these areas. Under rare conditions, when the radar is not tracking any...

  • Page 323

    Precautions while driving with fcw in certain driving conditions, such as: • driving in the vicinity of a curve • small vehicles and/or not aligned to the lane • lane changing of other vehicles • passing of vehicles in an oncoming intersection the intervention of the system could be unexpected or de...

  • Page 324

    Small vehicles and/or not aligned to the lane the system is not able to detect the presence of vehicles that are in front of the car but placed outside the field of action of the radar sensor and could therefore not react in the pres- ence of small vehicles such as bicycles or motorcycles. Lane chan...

  • Page 325

    Passing of vehicles in an oncoming intersection the system could temporarily react to a vehicle that crossed the range of the radar sensor, in an oncoming intersection. General information this vehicle has systems that operate on radio frequency that comply with part 15 of the federal communications...

  • Page 326

    Parksense® rear park assist — if equipped the parksense® rear park assist system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Refer to parksense® system usage precautions for limitations of th...

  • Page 327

    Chime by shifting the vehicle in reverse and in the case of the presence of a rear obstacle, an acoustic signal that varies with the distance of the obstacle from the bumper is activated. The frequency of the acoustic signal: • increases with the distance between car and object decreases. • becomes ...

  • Page 328

    If an obstacle is detected in the left and/or right rear region, the display will show a single flashing arc in the left and/or right rear region and will produce a fast sound tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the...

  • Page 329

    Caution! After turning off the ignition, the parksense® re- mains in this setting until the next key cycle, even in the case of changing the setting of starting mar/ run to stop/off and then again in mar/run. Service the rear park assist system during vehicle start up, when the parksense® rear park ...

  • Page 330

    Park assist system usage precautions note: • ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the rear park assist system operating properly. • jackhammers, large trucks, and other vibrations could affect the p...

  • Page 331

    Caution! (continued) • the vehicle must be driven slowly when using rear park assist in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using rear park assist. Warning! • drivers must be careful when backing up even wh...

  • Page 332

    Lanesense — if equipped lanesense operation the lanesense system is operational at speeds above 37 mph (60 km/h) and below 112 mph (180 km/h). The lanesense system uses a forward looking camera to detect lane markings and measure vehicle position within the lane boundaries. When both lane markings a...

  • Page 333

    Turning lanesense on or off the default status of lanesense is “off”. The lanesense button is located on the end of the turn signal stalk located on the steering column. To turn the lanesense system on, push the lane assist button (led turns off). A “lane sense on” message is shown in the evic. To t...

  • Page 334

    Left lane departure — only left lane detected • when the lanesense system is on, the lane assist indicator is solid white when only the left lane mark- ing has been detected and the system is ready to provide visual warnings in the evic if an uninten- tional lane departure occurs. • when the lanesen...

  • Page 335

    Left lane departure — both lanes detected • when the lanesense system is on, the lane lines turn from gray to white to indicate that both of the lane markings have been detected. The lanesense indicator is solid green when both lane markings have been detected and the system is “armed” to provide vi...

  • Page 336

    • for example: if approaching the left side of the lane the steering wheel will turn to the right. • when the lanesense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off) and the left thin line remains solid yellow. The l...

  • Page 337

    • for example: if approaching the left side of the lane the steering wheel will turn to the right. Note: the lanesense system operates with the similar behavior for a right lane departure. Changing lanesense status the lanesense system has settings to adjust the intensity of the torque warning and t...

  • Page 338

    Parkview® rear back up camera — if equipped the parkview® rear back up camera that allows you to see an on-screen image of your vehicle’s rear surround- ings when the shift lever is put into reverse. The image will be displayed on the touchscreen display along with a note to “check entire surroundin...

  • Page 339

    When the vehicle is shifted out of reverse (with camera delay turned on), the camera image will continue to be displayed for up to 10 seconds after shifting out of reverse unless the vehicle speed exceeds 8 mph (13 km/h), the vehicle is shifted into park or the ignition is switched to the stop/off p...

  • Page 340

    Note: if snow, ice, mud, or any foreign substance builds up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Warning! Drivers must be careful when backing up even when using the parkview® rear back up camera. Always check carefully behind your v...

  • Page 341

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12° f (6.5° c). This means that when the out...

  • Page 342

    For example, your vehicle may have a recommended cold (parked for more than three hours) tire pressure of 30 psi (207 kpa). If the ambient temperature is 68° f (20° c) and the measured tire pressure is 27 psi (186 kpa), a temperature drop to 20° f (-7° c) will decrease the tire pressure to approxima...

  • Page 343

    Caution! (continued) • after inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the tire pressure moni- toring sensor. Note: • the tpms is not intended to replace normal tire care and ma...

  • Page 344

    Base system this is the tpms warning indicator located in the instrument cluster. The tpms uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure lev- els. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver m...

  • Page 345

    Check tpms warnings the tire pressure monitoring telltale light will flash on and off for 75 seconds and remain on solid when a system fault is detected, an audible chime will be activated and the “service tire pressure monitoring system” text mes- sage will display. If the ignition key is cycled, t...

  • Page 346

    • this occurs for each subsequent ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will flash on and off for 75 seconds and then remain on solid. • once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare ti...

  • Page 347

    Fuel requirements 1.4l turbo engine this engine is designed to meet all emis- sion regulations and provide satisfactory fuel economy and performance when us- ing high-quality unleaded #regular# gaso- line having an octane rating of 87 using the (r+m)/2 method. For optimum performance and fuel econom...

  • Page 348

    Making a heavy knocking sound, see your dealer imme- diately. Use of gasoline with an octane number lower than 87 can cause engine failure and may void or not be covered by the new vehicle warranty. Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you exp...

  • Page 349

    E-85 usage in non-flex fuel vehicles non-flex fuel vehicles (ffv) are compatible with gaso- line containing up to 15% ethanol (e15). Gasoline with higher ethanol content may void the new vehicle lim- ited warranty. If a non-ffv vehicle is inadvertently fueled with e-85 fuel, the engine will have som...

  • Page 350

    Materials added to fuel besides using unleaded gasoline with the proper octane rating, gasolines that contain detergents, corrosion and stability additives are recommended. Using gasolines that have these additives will help improve fuel economy, reduce emissions, and maintain vehicle perfor- mance....

  • Page 351

    Caution! (continued) • the use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle perfor- mance problems resulting from the use of such fuels or additives is not the respon...

  • Page 352

    Warning! (continued) • guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Adding fuel the capless fuel system uses a flapp...

  • Page 353

    2. Insert the fuel nozzle in the filler pipe and proceed with filling the fuel tank. 3. Before removing the nozzle, wait at least 10 seconds to allow the fuel to flow inside of the tank. 4. Pull the nozzle from the filler pipe and then close the door. Emergency refueling procedure if the vehicle is ...

  • Page 354

    2. Open the fuel door. 3. Insert the emergency fuel fill funnel in the filler pipe and proceed to fill the fuel tank. 4. Remove the emergency fuel fill funnel, and close the door. 5. Store the emergency fuel fill funnel in the cargo area. Emergency fuel fill funnel — if equipped with full size spare...

  • Page 355

    Warning! • do not to affix objects/plugs to the end of the filler neck other than is provided on the car. • the use of objects/plugs do not comply with the vehicle and may cause pressure increases inside the tank, creating dangerous conditions. • do not approach the neck of the tank with open flames...

  • Page 356

    Rear axle systems (gawr). Total load must be limited so gvwr and front and rear gawr are not exceeded. Payload the payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo. Gross axle weight rating (gawr) th...

  • Page 357

    Curb weight the curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a comm...

  • Page 358

    Driving on slippery surfaces acceleration rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the driving wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. Warning! ...

  • Page 359

    Driving through water driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow...

  • Page 360

    Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • determine the condition of the road or the path that is under water and if there are any obstacles in the wa...

  • Page 361

    Power steering the electric power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will vary its assist to provide light efforts while parking and good feel while driving. If the electric steering system experiences a fault that re...

  • Page 362

    You will lose power steering assistance momentarily until the over temperature condition no longer exists. Once driving conditions are safe, then pull over and let vehicle idle for a few moments until the light turns off. Refer to “electronic vehicle information (evic)” in “getting to know your inst...

  • Page 363

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle front wheel drive (fwd) all-wheel drive (awd) towing condition wheels off the ground automatic transmission manual transmission manual/ automatic transmission flat tow none not allowed not allowed not allowed dol...

  • Page 364

    Note: you must ensure that the auto park brake feature is disabled before towing this vehicle, to avoid inadver- tent electric park brake engagement. The auto park brake feature is enabled or disabled via the customer programmable features in the uconnect® settings. Recreational towing front-wheel d...

  • Page 365

    Caution! • do not flat tow this vehicle. Damage to the drive- train will result. If this vehicle requires towing, make sure the drive wheels are off the ground. • towing this vehicle in violation of the above re- quirements can cause severe transmission damage. Damage from improper towing is not cov...

  • Page 367: In Case Of Emergency

    In case of emergency contents ! Hazard warning flashers . . . . . . . . . . .367 ! Bulb replacement . . . . . . . . . . . . . . . . . . .367 ▫ general information. . . . . . . . . . . . . . . . . . . .367 ▫ replacement bulbs . . . . . . . . . . . . . . . . . . . .368 ▫ replacing exterior bulbs . . ....

  • Page 368

    ! Tire service kit storage . . . . . . . . . . . . . .412 ▫ tire service kit . . . . . . . . . . . . . . . . . . . . . . .413 ! Jump starting . . . . . . . . . . . . . . . . . . . . . .417 ▫ preparations for jump start . . . . . . . . . . . . . .418 ▫ jump starting procedure . . . . . . . . . . . . ...

  • Page 369

    Hazard warning flashers the hazard warning flasher switch is located on the switch bank below the radio. Push the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the switch...

  • Page 370

    Replacement bulbs interior bulbs lamps bulb number front courtesy light c5w front courtesy lights (sun visors) c5w rear dome light (models without retractable roof) c5w rear interior lights (models with retractable roof) c5w interior lights w5w dome light (glove box) w5w 368 in case of emergency.

  • Page 371

    Exterior bulbs lamps bulb number low beam/high beam headlamps hir2 front position/daytime running lights (drl ) p21/5 front direction indicator lamps py21w front fog lamps h8 side indicators (side view mirror) wy5w tail/brake lights/turn indicators p21w center high mounted stop lamp (chmsl) led (ser...

  • Page 372

    Replacing exterior bulbs headlamps hi/lo beam light halogen to replace the bulbs proceed as follows: 1. Open the engine compartment and remove the head- lamp bulb cap. Front lamps 1 — headlamps 2 — daytime running lamps 3 — directional indicators 4 — fog lamps — if equipped headlamp bulb cap 370 in ...

  • Page 373

    2. Rotate the headlamp bulb socket counterclockwise then pull outwards. 3. Release the locking tab on the headlamp bulb connec- tor and remove the bulb and socket. 4. Install the new headlamp bulb making sure it is properly locked. 5. Install the headlamp bulb and socket; align the tabs and turn it ...

  • Page 374

    Warning! Carry out the operation of replacing lamps only with the engine off. Also make sure that the engine is cold, to avoid the danger of burns. Position lights/daytime running lights/fog lights to replace the bulbs proceed as follows: 1. Turn the front wheels completely. 2. Use a suitable tool t...

  • Page 375

    3. Remove the electrical connectors. 4. Rotate in a counterclockwise direction and remove the bulb and bulb socket. 5. To replace the bulb gently push bulb and rotate counterclockwise. Position light/daytime running light/fog light access 1 — screws 2 — access door position light/daytime running lig...

  • Page 376

    6. Insert the new bulb by pushing on it and turning it clockwise. Make sure the bulb is correctly locked in place. 7. Install the bulb and sockets and rotate them clockwise, making sure that it is properly locked. 8. Reconnect the electrical connectors. 9. Reinstall the access door. Front fog lights...

  • Page 377

    3. By pushing the electrical connector tab remove the electrical connector. 4. Rotate the bulb counterclockwise, and then replace the bulb. 5. Insert the new bulb in the socket, making sure the bulb is locked into place. Position light/daytime running light/fog light access 1 — screws 2 — access doo...

  • Page 378

    6. Reconnect the electrical connector. 7. Reinstall the access door. Side indicators on external rear view mirrors – (if equipped) caution! The procedure is described as a guideline. For the replacement of the lamp it is recommended that you contact your authorized dealer. To replace the bulb procee...

  • Page 379

    3. Remove the bulb socket and bulb from the transparent lens assembly by rotating the socket counterclockwise. 4. Remove the bulb from the bulb socket by pulling the bulb straight out. 5. Insert the new bulb, making sure that it is locked into place 6. Reinstall the socket in to the transparent lens...

  • Page 380

    3. Remove the rear tail lamp, sliding it toward the outside as shown. 4. Remove the screws and remove the rear tail lamp holder. 5. Replace the bulb as necessary. Tail lamp removal rear lamp assembly 1 — screws 378 in case of emergency.

  • Page 381

    6. Insert the new bulb, making sure it is properly locked. 7. Reassemble the lamp assembly on the rear tail lamp housing, tightening the screws. 8. Reposition the rear tail lamp on the car. 9. Secure the rear tail lamp and reconnect the electrical connector. 10. Finally close the liftgate. 3th stop ...

  • Page 382

    License plate lights to replace the bulbs proceed as follows: 1. Using a suitable tool remove the license plate lens. 2. Remove the bulbs from the individual side contacts. 3. Insert the new bulbs, and ensure that they are properly locked between the contacts. 4. Reinstall the license plate lens. Li...

  • Page 383

    Note: if removal the license plate lens using a suitable tool, be sure to cover the tip of the suitable with a cloth so no damage is done to the lenses or the vehicle paint. Replacing interior bulbs front courtesy light to replace the bulbs proceed as follows: 1. Using a suitable tool remove the fro...

  • Page 384

    3. Replace the bulbs by pulling straight out of bulb housing. 4. Insert the new bulbs, making sure that they are properly locked. Front courtesy bulb housing 1 — retaining clips 2 — bulb housing front courtesy bulb housing 382 in case of emergency.

  • Page 385

    5. Reassemble the bulb housing and courtesy light hous- ing making sure that they are properly locked. 6. Install the front courtesy light making sure that it is properly locked. Dome light vanity mirror to replace the bulbs proceed as follows: 1. Lift the cover of the mirror and pull out the visor ...

  • Page 386

    Dome light glove compartment to replace the bulb proceed as follows: 1. Open the glove compartment; 2. Place your fingers inside the light assembly, pull the bulb to replace it. 3. Insert the new bulb, making sure it is properly locked. Rear dome light — without retractable roof to replace the bulbs...

  • Page 387

    3. Insert the new bulb, locking it between the contacts. 4. Reinstall the dome light. Dome light to replace the bulbs proceed as follows: 1. Lower the handle in the direction shown remove the dome light. 2. Replace the bulb by removing it from the side contacts. Rear dome light retractable roof ligh...

  • Page 388

    3. Insert the new bulb, locking it between the contacts. 4. Reinstall the dome light. Interior cargo lights to replace the bulbs proceed as follows: 1. Open the luggage compartment and remove the dome light assembly. 2. Open the light cover and replace the bulb. Bulb light cover 386 in case of emerg...

  • Page 389

    3. Close the light cover over the bulb. 4. Reinstall the dome light in its correct position. Warning! • before proceeding with the replacement of the lamp wait for the exhaust pipes are cool: danger of burns! • modifications or repair of the electrical system performed incorrectly and without taking...

  • Page 390

    Fuses warning! • when replacing a blown fuse, always use an appro- priate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Failure to use proper fuses may re...

  • Page 391

    Fuse removal to replace a fuse use the extractor attached to the fuse cover (located on the inside of the engine compartment fuse cover. Blade fuses 1 — electrical circuit 2 — blade fuse with good electrical circuit 3 — blade fuse with bad electrical circuit fuse extractor location 8 in case of emer...

  • Page 392

    Access to the fuses the fuses are grouped into four controllers located in the engine compartment, under the instrument panel and on the inside of the left side cargo trim panel. Engine compartment fuses/distribution unit the engine compartment fuse panel is located on the left side of the engine co...

  • Page 393

    Removing fuse cover and locking screw proceed as follows: 1. Slowly turn the screw counterclockwise. 2. Slowly release the screw. 3. Remove the fuse cover by sliding it upward. Fuse panel and cover location 1 — mounting screw 2 — fuse cover 8 in case of emergency 391.

  • Page 394

    Mounting fuse cover and locking screw proceed as follows: 1. Properly secure the fuse cover to the box, slide com- pletely from top to bottom. 2. Fully depress the screw, using the special screwdriver supplied. 3. Slowly turn the screw clockwise. 4. Release the screw. Battery fuse cover location 1 —...

  • Page 395

    Cavity maxi fuse cartage fuse mini fuse description f01 70 amp tan – – module body computer f02 60 amp blue – – module body computer, rear distribution units f03 – 20 amp blue – controller power supply body computer f04 – 30 amp pink – brake control electronics module f05 70 amp tan – – electric pow...

  • Page 396

    Cavity maxi fuse cartage fuse mini fuse description f15 40 amp orange – – brake control module pump f16 – – 5 amp tan engine control module power, automatic transmission f17 – – 10 amp red 15 amp blue supply primary loads (1.4l) supply primary loads (2.4l) f18 – – 30 amp green – f19 – – 7.5 amp brow...

  • Page 397

    Cavity maxi fuse cartage fuse mini fuse description f83 – 40 amp green – air conditioning fan f84 – – 20 amp yellow power outlet (ignition powered) f87 – – 5 amp tan shift lever automatic transmission f88 – – 7.5 amp brown heated outside mirrors f89 – 30 amp pink – heated rear window f90 – – 5 amp t...

  • Page 398

    Body controller fuse cavities 396 in case of emergency.

  • Page 399

    Cav- ity mini fuse description f31 7.5 amp brown fan air conditioning, power socket f33 20 amp yellow power window front (passenger side) f34 20 amp yellow power window front (drivers side) f36 15 amp blue supply uconnect® system, air conditioning, usb port, rear lat- eral ceiling light in case of o...

  • Page 400

    Cav- ity mini fuse description f47 20 amp yellow power rear window (driver side) f48 20 amp yellow power rear window (passenger side) f49 7.5 amp brown supply parksense, spot lights front dome, internal electocromic mirror, heated front seats f50 7.5 amp brown supply air bag cav- ity mini fuse descr...

  • Page 401

    Rear cargo fuse/relay distribution unit to access the fuses, remove the access door from the left rear panel of the rear cargo area. Push on the left side of the access door to unhinge and remove. Cavity mini fuse description f2 20 amp yellow audio system f3 20 amp yellow my sky access door location...

  • Page 402

    Cavity mini fuse description f5 30 amp green power seat (driver side) f6 7.5 amp brown power seat (driver side) lumbar adjustment f8 20 amp yellow heating front seats jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far eno...

  • Page 403

    Jack location/spare tire stowage the jack and tools are located in the rear storage com- partment if equipped, inside a special container. 1. Open the liftgate. 2. Lift the access cover using the load floor handle. 3. Remove the fastener securing the spare tire. Jack and tools location load floor ha...

  • Page 404

    4. Remove the jack, wheel bolt wrench, and wheel chocks. Spare tire fastener jack and tools 1 — wheel bolt wrench 2 — jack 3 — emergency funnel 4 — wheel chocks 5 — screwdriver 6 — emergency allen key 402 in case of emergency.

  • Page 405

    5. Remove the spare tire. Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Preparations for jac...

  • Page 406

    6. Chock both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, chock the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jacking instructions warning! Carefully follow thes...

  • Page 407

    Warning! (continued) • to assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remo...

  • Page 408

    3. Before raising the vehicle, use the wheel bolt wrench to loosen, but not remove the wheel bolts on the wheel with the flat tire. Turn the wheel bolts counterclock- wise one turn while the wheel is still on the ground. 4. Place the jack underneath the lift area that is closest to the flat tire. Tu...

  • Page 409

    Front jacking location front jacking engagement point 8 in case of emergency 407.

  • Page 410

    5. Raise the vehicle just enough to remove the flat tire. Rear jacking location rear jacking engagement point 408 in case of emergency.

  • Page 411

    Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire. 7. Mount the spare tire. Caution! Be sure to mount the spare tire with the v...

  • Page 412

    Note: • your vehicle may be equipped with a compact spare tire or a limited — use spare tire. For further infor- mation refer to “tires — general information” in “maintaining and caring for your vehicle”. • for vehicles so equipped, do not attempt to install a center cap or wheel cover on the compac...

  • Page 413

    Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Road tire installation 1. Mount the road tire ...

  • Page 414

    5. Lower the jack until it is free. Remove the wheel chocks. Stow the jack and tools back in the proper storage location. Release the electric park brake before driving the vehicle. 6. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel bolts are properly...

  • Page 415

    Tire service kit if a tire is punctured, you can make a first emergency repair using the tire service kit located in the rear storage compartment inside the storage container. Tire punctures of up to 1/4” (6 mm) can be repaired; the kit can be used in all weather conditions. Do not remove the foreig...

  • Page 416

    Warning! (continued) • do not use tire service kit or drive the vehicle under the following circumstances: – if the puncture in the tire tread is approximately 1/4” (6 mm) or larger. – if the tire has any sidewall damage. – if the tire has any damage from driving with extremely low tire pressure. – ...

  • Page 417

    Warning! (continued) • tire service kit sealant solution contains latex. In case of an allergic reaction or rash, consult a phy- sician immediately. Keep tire service kit out of reach of children. If swallowed, rinse mouth imme- diately with plenty of water and drink plenty of water. Do not induce v...

  • Page 418

    Warning! Tire service kit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using tire service kit. Do not exceed 65 mph (110 km/h) until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you...

  • Page 419

    Warning! Store the sealant canister in its special compartment, away from sources of heat. Failure to follow this warning may result in sealant canister rupture and serious injury or death. Jump starting if your vehicle has a discharged battery it can be jump- started using a set of jumper cables an...

  • Page 420

    Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations for jump start the battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. Battery posts 1 — positive battery pos...

  • Page 421

    Note: the positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post. Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan bla...

  • Page 422

    Jump starting procedure warning! Failure to follow this jump-starting procedure could result in personal injury or property damage due to battery explosion. Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Con...

  • Page 423

    5. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the...

  • Page 424

    Enhanced accident response system in the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the orc will determine whether to have the enhanced accident response sys- tem perform the following functions: • cut off fuel...

  • Page 425

    Customer action customer will see 1. Turn ignition off. (turn signal switch must be placed in neutral state). 2. Turn ignition on. Left turn light is off. Right turn light blinks. 3. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 4. Turn left turn signal swit...

  • Page 426

    Refueling in emergency the fuel filling procedure in case of emergency is de- scribed in the “emergency refueling procedure”. Refer to “adding fuel” in “starting and operating” for further information. If your engine overheats in any of the following situations, you can reduce the potential for over...

  • Page 427

    • you can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. Warning! You or others can be badly burned by hot engine...

  • Page 428

    4. Push and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool down into the shift lever override access hole (at the right front corner of the shift lever assembly), and push and hold the override release lever down. Shift lever bezel location removing shift le...

  • Page 429

    6. Move the shift lever to the neutral position. 7. The vehicle may then be started in neutral. 8. Reinstall the shift lever bezel. Ignition key removal override this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can...

  • Page 430

    4. Using the special tool supplied (located in the tool bag), remove the screws in the lower steering column trim cover and remove it. Special tool lower steering column cover 1 — trim screws 428 in case of emergency.

  • Page 431

    5. With one hand, pull down on the release tab and with the other, pull out the ignition key. 6. Once the key is removed, reinstall the steering column cover. Release tab location release tab direction 8 in case of emergency 429.

  • Page 432

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. For vehicles with automatic transmission, push and hold the lock button on the shift lever. Then...

  • Page 433

    Caution! • racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in neutral for at least one minute after every five rocking- motion cycles. This will minimize overheating and reduce the risk of clutch or transmissio...

  • Page 434

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial towing service. Fwd models all wheel drive towing condition wheels off the ground automatic transmission manual transmission automatic/manual transmission awd flat tow none not allowed not al...

  • Page 435

    Note: • you must ensure that the auto park brake feature is disabled before towing this vehicle, to avoid inadver- tent electric park brake engagement. The auto park brake feature is enabled or disabled via the customer programmable features in the uconnect settings. • vehicles with a discharged bat...

  • Page 436

    Caution! • do not use sling type equipment when towing. Vehicle damage may occur. • when securing the vehicle to a flat bed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. Front wheel drive (fwd) models the manufacturer recommends ...

  • Page 437

    Caution! • do not tow this vehicle with any of its wheels on the ground. Damage to the drivetrain will result. • front or rear wheel lifts must not be used. Internal damage to the transmission or power transfer unit will occur if a front or rear wheel lift is used when towing. • towing this vehicle ...

  • Page 438

    Tow eye usage precautions note: • ensure that the tow eye is properly seated and secure in the mounting receptacle. • the tow eye is recommended for use with an approved tow bar and or rope. • do not use the tow eye to pull the vehicle onto a flatbed truck. • do not use the tow eye to free a stuck v...

  • Page 439

    Caution! • the tow eye must be used exclusively for roadside assistance operations. Only use the tow eye with an appropriate device in accordance with the highway code (a rigid bar or rope) to flat tow the vehicle for a short distance to the nearest service location. • tow eyes must not be used to t...

  • Page 440

    Front tow eye installation the front tow eye receptacle is located behind a access door, located on the right front bumper fascia. To install the tow eye, open the access door using the vehicle key or a small screwdriver, and thread the tow eye into the receptacle. Insert the wheel bolt wrench handl...

  • Page 441

    Rear tow eye installation the rear tow eye receptacle is located behind a access door on the rear bumper fascia. To install the tow eye, open the access door using the vehicle key or a small screwdriver, and thread the tow eye into the receptacle. Insert the wheel bolt wrench handle through the eye ...

  • Page 443: Contents

    Maintaining and caring for your vehicle contents ! Emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . . .444 ! Replacement parts . . . . . . . . . . . . . . . . . .445 ! Dealer service . . . . . . . . . . . . . . . . . . . . . .446 ! Maintenance schedule . ...

  • Page 444

    ▫ cooling system . . . . . . . . . . . . . . . . . . . . . .473 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . .479 ▫ manual transmission — if equipped . . . . . . .481 ▫ automatic transmission — if equipped . . . . .482 ▫ appearance care and protection from corrosion . . . . . . . . ....

  • Page 445

    ! Tire chains (traction devices) . . . . . . .515 ! Tire rotation recommendations . . . . .516 ! Storing the vehicle . . . . . . . . . . . . . . . . .518 9 maintaining and caring for your vehicle 443.

  • Page 446

    Emissions inspection and maintenance programs in some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states that require an inspection and mainte- nance (i/m), this check verifies the...

  • Page 447

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 448

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 449

    Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “electronic vehicle information center...

  • Page 450

    Once a month or before a long trip: • check engine oil level. • check windshield washer fluid level. • check the tire inflation pressures and look for unusual wear or damage. • check the fluid levels of the coolant reservoir, and brake master cylinder reservoir, and fill as needed. • check function ...

  • Page 451

    Maintenance chart mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 16...

  • Page 452

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,...

  • Page 453

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,...

  • Page 454

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,...

  • Page 455

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,...

  • Page 456

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,...

  • Page 457

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,...

  • Page 458

    Mileage or time passed (whichever comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers 16,000 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,...

  • Page 459

    (**) the spark plug change is distance based only, yearly intervals do not apply. The following are essential to ensure correct operation and prevent serious damage to the engine: • only use spark plugs of the same make and type which are specially certified for such engines (refer to “fluids, lubri...

  • Page 460

    Engine compartment — 1.4l turbo engine 1 — air cleaner filter 4 — battery 7 — coolant pressure cap 2 — engine oil dipstick 5 — power distribution center (fuses) 8 — coolant pressure bottle 3 — brake fluid reservoir 6 — washer fluid reservoir 9 — oil fill cap 458 maintaining and caring for your vehic...

  • Page 461

    Engine compartment — 2.4l engine 1 — engine air cleaner filter 4 — brake fluid reservoir 7 — washer fluid reservoir 2 — engine oil dipstick 5 — battery 8 — coolant pressure cap 3 — engine oil fill cap 6 — power distribution center (fuses) 9 — coolant pressure bottle 9 maintaining and caring for your...

  • Page 462

    Maintenance procedures the pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the futu...

  • Page 463

    Engine oil checking oil level to assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is approximately five minutes after a fully warmed engine is shut ...

  • Page 464

    Engine oil selection — 1.4l turbo engine for best performance and maximum protection for tur- bocharged engines under all types of operating condi- tions, the manufacturer recommends synthetic engine oils that are api certified and meet the requirements of chrysler material standard ms-12991. Engine...

  • Page 465

    Lubricants which do not have both the engine oil certi- fication mark and the correct sae viscosity grade num- ber should not be used. Materials added to engine oil the manufacturer strongly recommends against the addi- tion of any additives (other than leak detection dyes) to the engine oil. Engine...

  • Page 466

    Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine comp...

  • Page 467

    Warning! (continued) • battery gas is flammable and explosive. Keep flame or sparks away from the battery. Do not use a booster battery or any other booster source with an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories...

  • Page 468

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 469

    Refrigerant recovery and recycling hfo 1234yf hfo 1234yf air conditioning refrigerant is a hydro- fluorocarbon (hfc) that is endorsed by the environmen- tal protection agency and is an ozone-saving product. The manufacturer recommends that air conditioning service be performed by authorized dealer u...

  • Page 470

    Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield or rear window. Avoid using the wiper blades to remove frost or ice from the windshield or rear window. Make s...

  • Page 471

    Function deactivation: the functionality is reset if: • turn the ignition to the mar/run position. • number of subsequent activations is three. • two minutes timer has expired after turning the ignition off. Note: when turning the ignition on, the blades will go into the parking position. Front wipe...

  • Page 472

    Rear wiper blade removal/installation 1. Carefully lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 2. Grab and hold the wiper arm closest to the wiper blade end while pushing the wiper blade towards the liftgate glass to unsnap the blade pivot pin from the wiper bl...

  • Page 473

    Have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, have the exhaust system inspected e...

  • Page 474

    Caution! (continued) • damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of ...

  • Page 475

    Cooling system warning! • when working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at any time the ignition switch is in the on position. • you or others can be badly burned by hot eng...

  • Page 476

    If the engine coolant (antifreeze) is dirty or contains visible sediment, have an authorized dealer clean and flush with oat coolant (antifreeze) (conforming to ms.90032). Refer to the “maintenance schedule” for the proper maintenance intervals. Selection of coolant refer to “fluids, lubricants, and...

  • Page 477

    Caution! (continued) • this vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (anti- freeze) is not recommended. Adding coolant your vehicle has been built with an improved engine coolant (oat coolant conformin...

  • Page 478

    Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. Note: • some vehicles require special tools to add coolant properly. Failure to fill these systems prop...

  • Page 479

    Warning! (continued) • do not use a pressure cap other than the one specified for your vehicle. Personal injury or en- gine damage may result. Disposal of used engine coolant used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your lo...

  • Page 480

    Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when th...

  • Page 481

    Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “maintenance schedule” for the proper maintenance intervals. Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot rest...

  • Page 482

    Use only manufacturer’s recommended brake fluid. Re- fer to “fluids, lubricants, and genuine parts” in the “technical data” section for further information. Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in the “technical data” section fo...

  • Page 483

    Warning! (continued) • overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire. Brake fluid can also damage painted and vinyl surfaces, care should be taken to avoid its contact with these surfaces. Caution! Use of improper ...

  • Page 484

    Frequency of fluid change under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless lubri- cant has become contaminated with water. Note: if contaminated with water, the fluid should be...

  • Page 485

    Special additives the manufacturer strongly recommends against using any special additives in the transmission. Automatic transmission fluid (atf) is an engineered product and its performance may be impaired by supplemental addi- tives. Therefore, do not add any fluid additives to the transmission. ...

  • Page 486

    Fluid and filter changes under normal operating conditions, the fluid installed at the factory will provide satisfactory lubrication for the life of the vehicle. Routine fluid and filter changes are not required. How- ever, change the fluid and filter if the fluid becomes contaminated (with water, e...

  • Page 487

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar® car wash, or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover...

  • Page 488

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as...

  • Page 489

    Caution! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s pro- tective finish. Only mopar® whee...

  • Page 490

    Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar® total clean. ...

  • Page 491

    Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses ...

  • Page 492

    Instrument panel bezels caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Cleaning plastic instrument cluster lenses the...

  • Page 493

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 494

    The vehicle lifting points on the vehicle are marked on side skirts with symbols ( see example shown). Lifting point locations 492 maintaining and caring for your vehicle.

  • Page 495

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 496

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 497

    Example: r = construction code – #r# means radial construction, or – #d# means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the r...

  • Page 498

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 499

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 500

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 501

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 9 maintaining a...

  • Page 502

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 503

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 504

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 505

    9 maintaining and caring for your vehicle 503.

  • Page 506

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 507

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 508

    Tire inflation pressures the proper cold tire inflation pressure is listed on the driver’s side b-pillar or rear edge of the driver’s side door. At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judge- ment when determining p...

  • Page 509

    Example: if garage temperature = 68°f (20°c) and the outside temperature = 32°f (0°c) then the cold tire inflation pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12°f (7°c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to...

  • Page 510

    Radial ply tires warning! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause a collision. Al- ways use radial ply tires in sets of four. Never combine them with other types of tires. Tire repair if your tire beco...

  • Page 511

    Summer or three season tires — if equipped summer tires provide traction in both wet and dry conditions, and are not intended to be driven in snow or on ice. If your vehicle is equipped with summer tires, be aware these tires are not designed for winter or cold driving conditions. Install winter tir...

  • Page 512

    Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). For speeds above 75 mph (120 km/h) refer to original equipment or an authorized tire dealer for recommended safe operating speeds, ...

  • Page 513

    Spare tires — if equipped note: for vehicles equipped with tire service kit instead of a spare tire, please refer to “tire service kit” in “in case of emergency” for further information. Caution! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a c...

  • Page 514

    Tread wear indicators tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (2 mm). When the t...

  • Page 515

    • performance tires, tires with a speed rating of v or higher, and summer tires typically have a reduced tread life. Rotation of these tires per the vehicle main- tenance schedule is highly recommended. Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining...

  • Page 516

    It is recommended to replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling. If you ever replace a wheel, make sure that the wheel’s specifications match those of the original wheels. It is recommended you contact your authorized...

  • Page 517

    Caution! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage. • traction device must be ...

  • Page 518

    Caution! (continued) • install device as tightly as possible and then re- tighten after driving about ½ mile (0.8 km). • do not exceed 30 mph (48 km/h). • drive cautiously and avoid severe turns and large bumps, especially with a loaded vehicle. • do not drive for a prolonged period on dry pave- men...

  • Page 519

    The suggested front wheel drive (fwd) rotation method is the “rearward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. The suggested four wheel drive (4wd) tire rotation method is the “forward-cross” shown in the follow...

  • Page 520

    Caution! Proper operation of four-wheel drive vehicles de- pends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the power transfer unit. Tire rotation schedule should be followed to balance tire wear. Storing the vehicle if the vehicle s...

  • Page 521

    • do not drain the engine cooling system. • whenever you leave the vehicle is stationary for two weeks or more, run the at engine idling and for approximately five minutes, with the air conditioning system on and high fan speed. This will ensure a proper lubrication of the system, thus minimizing th...

  • Page 523: Technical Data

    Technical data contents ! Vehicle identification number . . . . . . .522 ! Wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .523 ▫ torque specifications . . . . . . . . . . . . . . . . . . .523 ! Fluid capacities . . . . . . . . . . . . . . . . . . . .525 ! Fluids, lubr...

  • Page 524

    Vehicle identification number the chassis number (vin) and stamped on the plate illustrated in, located on the left front corner of the instrument panel cover, visible from the outside car through the windshield. This number is also stamped on the floor of the passenger compartment, in front of the ...

  • Page 525

    Wheel and tire torque specifications proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle the lug nuts/bolts should be torqued using a properly calibrated torque wrench. Torque speci...

  • Page 526

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten...

  • Page 527

    Fluid capacities u.S metric fuel (approximate) 1.4l turbo/2.4l engine 12.7 gallons 48 liters engine oil with filter 1.4l turbo engine (sae 5w-40 synthetic, api certified) 4.0 quarts 3.8 liters 2.4l engine (sae 0w-20, api certified) 5.5 quarts 5.2 liters cooling system * 1.4l turbo engine (mopar® ant...

  • Page 528

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/ 150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of chrysler material standard ms.90032. Engine...

  • Page 529

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped we recommend you use mopar® c series manual & dual dry clutch transmission fluid. Automatic transmission – if equipped use only mopar® zf 8&9 speed atf™ automatic transmission fluid, or equivalent. Failure to use t...

  • Page 531: Multimedia

    Multimedia contents ! Uconnect® settings. . . . . . . . . . . . . . . . . . . .531 ▫ buttons on the faceplate. . . . . . . . . . . . . . . .532 ▫ buttons on the touchscreen. . . . . . . . . . . . . .533 ▫ customer programmable features — uconnect® 5.0 settings . . . . . . . . . . . . . . . . .533 ▫ ...

  • Page 532

    ▫ basic voice commands. . . . . . . . . . . . . . . . . .577 ▫ radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .578 ▫ media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .580 ▫ phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .581 ▫ voice text reply . . . . ....

  • Page 533

    Uconnect® settings the uconnect® system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allow you to access and change the customer programmable features. Many features can vary by vehicle. Uconnect® 5.0 buttons on the ...

  • Page 534

    Buttons on the faceplate buttons on the faceplate are located below, and beside the uconnect® system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side. Turn the control knob to scroll through menus and change settings (i.E., 30, 60, 90...

  • Page 535

    Buttons on the touchscreen buttons on the touchscreen are accessible on the uconnect® touchscreen. Customer programmable features — uconnect® 5.0 settings push the settings button on the faceplate, to display the settings menu screen. In this mode the uconnect® system allows you to access programmab...

  • Page 536

    Display after pressing the “display” button on the touchscreen the following settings will be available. • display mode when in this display you may select the “auto” or “manual” display settings. To change mode status, press and release the “auto” or “manual” button on the touchscreen. Then press t...

  • Page 537

    Units after pressing the “units” button on the touchscreen you may select each unit of measure independently displayed in the electronic vehicle information system (evic). The following selectable units of measure are listed below: • us changes the evic to us units of measure. • metric changes the e...

  • Page 538

    • show command list when in this display, you may change the show com- mand list settings. To change the show command list settings, press the “show command list” button on the touchscreen and select from “always,” “with help” or “never.” press the back arrow button on the touchscreen to return to t...

  • Page 539

    • sync time — if equipped when in this display, you may sync the time with gps. Press the “sync time” button on the touchscreen and select from “on” or “off.” press the back arrow or done button on the touchscreen to return to the previous menu. Safety/assistance after pressing the “safety/assistanc...

  • Page 540

    • parkview® backup camera fixed guide lines — if equipped when this feature is enabled, fixed (static) grid lines are overlaid on the rear backup camera image to illustrate the width of the vehicle. • forward collision warning-plus (fcw+) — if equipped the front collision warning (fcw+) feature can ...

  • Page 541

    System can be enabled with sound only, or sound and display. To change the parksense® status, press and release the “sound only” or “sounds and display” button. Then press the back arrow button on the touch- screen. Refer to “parksense®” in “starting and operat- ing” for system function and operatin...

  • Page 542

    • lanesense strength — if equipped when this feature is selected, it sets the strength of the steering wheel feedback for potential lane departures. The amount of directional torque the steering system can apply to the steering wheel to correct for vehicle lane departure can be set at “low,” “medium...

  • Page 543

    • electric park brake service mode this feature provides a means for a technician or vehicle owner to utilize a vehicle integrated, menu driven sys- tem, to command the electric park brake retraction, to service the rear foundation brakes (brake pads, calipers, rotors, etc.). For further information...

  • Page 544

    • greeting lights when this feature is selected, it allows the greeting lights to be turned on or off. To change the greeting lights setting, press the “on” or “off” button on the touch- screen to select your desired greeting light setting. Press the back arrow button on the touchscreen to return to...

  • Page 545

    • flash lights with lock — if equipped when this feature is selected, the exterior lights will flash when the doors are locked or unlocked with the remote keyless entry (rke) transmitter. This feature may be selected with or without the sound horn on lock feature selected. To make your selection, pr...

  • Page 546

    • horn with lock when this feature is selected, the horn will sound when the key fob lock button is pressed. To make your selection, press the “horn w/lock” button on the touch- screen and select from #off,” “1st press,” or “2nd press” press the back arrow/done button on the touchscreen to return to...

  • Page 547

    Note: if “all” is programmed, all doors will unlock no matter which passive entry equipped door handle is grasped. If “driver” is programmed, only the driver’s door will unlock when the driver’s door is grasped. Touching the handle more than once will only result in the driver’s door opening once. I...

  • Page 548

    Note: bass/mid/treble allow you to simply slide your finger up or down to change the setting as well as press directly on the desired setting. • balance/fade when in this display you may adjust the balance and fade settings. • speed adjusted volume this feature increases or decreases volume relative...

  • Page 549

    • auto-on radio the radio automatically turns on when vehicle is in run or will recall whether it was on or off at last ignition off. To make your selection, press the “loudness” button on the touchscreen, select “on,” “off” or “recall last” followed by pressing the back arrow button on the touchscr...

  • Page 550

    Press the “subscription info” button on the touchscreen to access the subscription information screen. Write down the sirius id numbers for your receiver. To reactivate your service, either call the number listed on the screen or visit the provider online. Note: siriusxm travel link is a separate su...

  • Page 551

    Customer programmable features — uconnect® 6.5an settings press the settings button to display the menu setting screen. In this mode the uconnect® system allows you to access programmable features that may be equipped such as display, clock, safety & driving assistance, lights, doors & locks, engine...

  • Page 552

    Note: when day or night is selected for the display mode, the usage of the parade mode feature will cause the radio to activate the display brightness day control even though the headlights are on. • display brightness with headlights on this feature will allow you to select the brightness with the ...

  • Page 553

    Units • units when in this display, you may select to have the elec- tronic vehicle information system (evic), odometer, and navigation system (if equipped) changed between us and metric units of measure. Press “us” or “metric.” press the back arrow button on the touchscreen to return to the previou...

  • Page 554

    Custom units can be customized independently from: • distance select from: “mi” or “km.” • fuel consumption select from: “mpg” (us), “mpg” (uk), “l/100 km” or “km/l” according to distance unit measure cho- sen. • pressure select from: “psi,” “kpa” or “bar.” • temperature select from: “°f” or “°c.” v...

  • Page 555

    Clock after pressing the “clock” button on the touchscreen the following settings will be available: • show time in status bar this feature will allow you to turn on or shut off the digital clock in the status bar. To change the show time status setting press the “on” or “off” button on the touchscr...

  • Page 556

    • set hours this feature will allow you to adjust the hours. The sync time with gps “on” button must not be selected. To make your selection, press the “–” or “+” buttons on the touchscreen to adjust the hours up or down. Press the back arrow button on the touchscreen to return to the previous menu....

  • Page 557

    Time. To change the setting for a more dynamic driving experience, select the near setting. This warns you of a possible collision when you are much closer to the vehicle in front of you. To change the fcw+ status, press the “fwd collision warning” button and select the “near”, “medium” or “far” but...

  • Page 558

    • lanesense strength — if equipped when this feature is selected, it sets the strength of the steering wheel feedback for potential lane departures. The amount of directional torque the steering system can apply to the steering wheel to correct for vehicle lane departure can be set at “low,” “med” o...

  • Page 559

    • front parksense® volume — if equipped front park assist chime volume settings can be selected from the evic or uconnect® system (if equipped). The chime volume settings include “low,” “medium,” and “high.” the factory default volume setting is medium. • blind spot alert — if equipped when this fea...

  • Page 560

    • parkview® backup camera active guidelines — if equipped your vehicle may be equipped with the parkview® rear back up camera active guidelines that allows you to see active guidelines over the parkview back up camera display whenever the shift lever/gear selector is put into reverse. The image will...

  • Page 561

    • brakes this feature provides a means for a technician or vehicle owner to utilize a vehicle integrated, menu driven sys- tem, to command the electric park brake retraction, to service the rear foundation brakes (brake pads, calipers, rotors, etc.). For further information, refer to “service mode (...

  • Page 562

    Note: the greater the sensitivity set, the less the external light variation required to turn on the lights (e.G. With a setting on level 3 at sunset the headlights turn on earlier than in levels 1 and 2). To change the headlight sensitivity setting, press the “1,” “2” or “3” button on the touchscre...

  • Page 563

    • daytime running lights when this feature is selected, the headlights will turn on while the engine is running. To make your selection, press the “daytime running lights” button on the touch- screen, then choose “yes” or “no.” the button will highlight indicating that the setting has been selected....

  • Page 564

    Press the back arrow button on the touchscreen to return to the previous menu. Doors & locks after pressing the “doors & locks” button on the touch- screen the following settings will be available: • auto door locks when this feature is selected, all doors will lock auto- matically when the vehicle ...

  • Page 565

    • sound horn with lock when this feature is selected, the horn will sound when the door locks are activated. To make your selection, press the “sound horn with remote lock” button on the touchscreen, then choose “1st press” “2nd press” or “off.” the button will highlight indicating that the setting ...

  • Page 566

    Touchscreen, then choose “on” or “off.” the button will highlight indicating that the setting has been selected. Press the back arrow/done button on the touchscreen to return to the previous menu. • memory linked to key fob — if equipped this feature provides automatic driver seat positioning to enh...

  • Page 567

    Audio after pressing the “audio” button on the touchscreen the following settings will be available: • balance/fade when in this display you may adjust the balance and fade settings. Press and drag the speaker icon, use the arrows to adjust, or tap the speaker icon to readjust to the center. • equal...

  • Page 568

    • aux volume offset — if equipped this feature provides the ability to tune the audio level for portable devices connected through the aux input. To make your selection, press the “aux volume offset” button on the touchscreen, select any point on the scale between the “+” and “–” buttons on the touc...

  • Page 569

    Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touch- screen, the following settings will be available: • channel skip siriusxm can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scannin...

  • Page 570

    Clear personal data after pressing the “clear personal data settings” button on the touchscreen the following settings will be avail- able: • clear personal data when this feature is selected it will remove personal data including bluetooth® devices and presets. To clear per- sonal data press the “y...

  • Page 571

    Located below the heating ventilation and air condition- ing controls is the front usb port. Refer to the uconnect® radio supplement for external usb support capability. Center console usb port located in the center console is a second usb port. Note: depending on vehicle configuration, the usb port...

  • Page 572

    Steering wheel audio controls the remote sound system controls are located at the rear of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pushing th...

  • Page 573

    Radio operation pushing the top of the switch will “seek” up for the next listenable station and pushing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gramme...

  • Page 574

    Regulatory and safety information usa/canada exposure to radio frequency radiation the radiated output power of the internal wireless radio is far below the fcc radio frequency exposure limits. Nevertheless, the wireless radio will be used in such a manner that the radio is 20 cm or further from the...

  • Page 575

    Note: • this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful inter- ference in a residential installation. This equipment generates, uses and c...

  • Page 576

    Uconnect® voice recognition quick tips introducing uconnect® start using uconnect® voice recognition with these helpful quick tips. It provides the key voice commands and tips you need to know to control your uconnect® 5.0 or 6.5an system. Key features: • five-inch color touchscreen display with am/...

  • Page 577

    Key features: • 6.5-inch color touchscreen display with am/fm/ usb/sd card/bluetooth® • bluetooth with integrated voice control • gps navigation (if equipped) get started all you need to control your uconnect® system with your voice are the buttons on your steering wheel. 1. Visit uconnectphone.Com ...

  • Page 578

    3. Speak clearly at a normal pace and volume while facing straight ahead. The microphone is positioned on the rearview mirror and aimed at the driver. 4. Each time you give a voice command, you must first push either the vr or phone button, wait until after the beep, then say your voice command. 5. ...

  • Page 579

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect® system. Push the vr button . After the beep, say& • cancel to stop a current voice session. • help to hear a list of suggested voice commands. • repeat to listen to the system prompts again. Noti...

  • Page 580

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio® stations you would like to hear. (sub- scription or included siriusxm satellite radio® trial required.) push the vr button . After the beep, say& • tune to ninety-five-point-five fm. • tune to satellite channel hits 1. Ti...

  • Page 581

    Uconnect® 5.0 radio uconnect® 6.5an radio 11 multimedia 579.

  • Page 582

    Media uconnect® offers connections via usb port, bluetooth® and auxiliary ports (if equipped). Voice operation is only available for connected usb and ipod® devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands ...

  • Page 583

    Phone making and answering hands-free phone calls is easy with uconnect®. When the phonebook button is illumi- nated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Push the phone button . After the beep, say one of the foll...

  • Page 584

    Tip: when providing a voice command, push the phone button and say “call,” then pronounce the name exactly as it appears in your phone book. When a contact has multiple phone numbers, you can say “call john smith work.” uconnect® 5.0 phone uconnect® 6.5an phone 582 multimedia.

  • Page 585

    Voice text reply uconnect® will announce incoming text messages. Push the phone button and say “listen.” (must have compatible mobile phone paired to uconnect® sys- tem.) 1. Once an incoming text message is read to you, push the phone button . After the beep, say: “reply.” 2. Listen to the uconnect®...

  • Page 586

    Navigation (6.5an) the uconnect® navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. 1. To enter a destination, push the vr button . After the beep, say: • for the 6.5an uconnect® system, say: “navigate to 800 chrysler drive aub...

  • Page 587

    Register (6.5an) 1. Press the apps button on the 6.5-inch touchscreen. 2. If a pop-up message appears, press register or go to the favorite apps menu and press uconnect® regis- tration . 3. Read through the registration instructions. Enter and confirm your personal email address. Then press send . 4...

  • Page 588

    Mobile app (6.5an) securely link your mobile device to your vehicle with the uconnect® access app. Once you have downloaded the app, you may start your vehicle or lock it from virtually any distance. (vehicle must be properly equipped with factory-installed remote start.) download the uconnect® acce...

  • Page 589

    Siriusxm travel link™ (6.5an) need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? Siriusxm travel link™ is a suite of services that brings a wealth of information right to your uconnect® 6.5an system. Push the vr button . After the beep, say o...

  • Page 590

    Additional information © 2015 fca us llc. All rights reserved. Mopar and uconnect are registered trademarks and mopar owner connect is a trademark of fca us llc. Android is a trademark of google inc. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. Uconnect® system supp...

  • Page 591: Index

    Index 12.

  • Page 592

    About your brakes . . . . . . . . . . . . . . . . . . . . . . . .201 adding engine coolant (antifreeze) . . . . . . . . . . . .475 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .350 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .470 additives, fuel . . . . . . ....

  • Page 593

    Audio systems (radio) . . . . . . . . . . . . . . . . . . . . .568 automatic headlights . . . . . . . . . . . . . . . . . . . . . . .95 automatic temperature control (atc) sync temperature button . . . . . . . . . . . . . . . . .125 automatic transmission . . . . . . . . . . . . . . . . . . . .297 a...

  • Page 594

    Chains, tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .515 changing a flat tire . . . . . . . . . . . . . . . . . . . . . . .400 chart, tire sizing . . . . . . . . . . . . . . . . . . . . . . . . .494 check engine light (malfunction indicator light) . . .444 checking your vehicle for ...

  • Page 595

    Cooling system. . . . . . . . . . . . . . . . . . . . . . . . . . .473 adding coolant (antifreeze) . . . . . . . . . . . . . . .475 coolant capacity . . . . . . . . . . . . . . . . . . . . . . .525 coolant level . . . . . . . . . . . . . . . . . . . . . . . . . .473 disposal of used coolant . . . . ...

  • Page 596

    Electronic brake control system anti-lock brake system . . . . . . . . . . . . . . . . . .202 electronic roll mitigation . . . . . . . . . . . . . . . . .210 traction control system . . . . . . . . . . . . . . . . . . .208 electronic speed control (cruise control) . . . . . . . .309 electronic vehic...

  • Page 597

    Filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .463 air conditioning . . . . . . . . . . . . . . . . . . . . . . .467 engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .463 engine oil disposal . . . . . . . . . . . . . . . . . . . . .463 flashers hazard warnin...

  • Page 598

    General maintenance. . . . . . . . . . . . . . . . . . . . . . .460 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .489 gvwr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .353 hazard driving through flowing, rising, or shallow standing water . . . . . . . . . . ...

  • Page 599

    Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 jacking instructions. . . . . . . . . . . . . . . . . . . . . . . .404 jack location . . . . . . . . . . . . . . . . . . . . . . . . . . . .401 jack operation . . . . . . . . . . . . . . . . . . . . . . . . . . .400 jump start...

  • Page 600

    Dimmer switch, headlight . . . . . . . . . . . . . . . . .97 exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .274 fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 hazard warning flasher . . . . . . . . . . . . . . . . . .367 headlights . . . . . . . . . . ...

  • Page 601

    Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 modifications/alterations, vehicle . . . . . . . . . . . . . . .7 mtbe/etbe . . . . ....

  • Page 602

    Preparation for jacking . . . . . . . . . . . . . . . . . . . . .403 pretensioners seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 radial ply tires . . . . . . . . . . . . . . . . . . . . . . . . . .508 radio operation . . . . . . . . . . . . . . . . . . . . . . . . . .571 ra...

  • Page 603

    Roof type carrier . . . . . . . . . . . . . . . . . . . . . . . . .157 rotation, tires . . . . . . . . . . . . . . . . . . . . . . . . . . .516 safety checks inside vehicle . . . . . . . . . . . . . . . . .272 safety checks outside vehicle . . . . . . . . . . . . . . . .274 safety defects, reporting...

  • Page 604

    Tilting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 security alarm arm the system . . . . . . . . . . . . . . . . . . . . . . . .49 selection of coolant (antifreeze) . . . . . . . . . . . . . .526 sentry key® fcc general information . . . . . . . . . . . . . . . . . .48 sentry ...

  • Page 605

    Sun visor extension . . . . . . . . . . . . . . . . . . . . . . .149 supplemental restraint system - air bag. . . . . . . . .231 system, remote starting . . . . . . . . . . . . . . . . . . . . .43 telescoping steering column . . . . . . . . . . . . . . . . . .77 temperature control, automatic (atc) ...

  • Page 606

    Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .356 traction control . . . . . . . . . . . . . . . . . . . . . . . . . .208 trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . . .360 transfer case fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 607

    Washer adding fluid . . . . . . . . . . . . . . . . . . . . . . . . . .470 washing vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .485 water driving through . . . . . . . . . . . . . . . . . . . . . . . .357 wheel and wheel trim . . . . . . . . . . . . . . . . . . . . .486 wheel and wheel...

  • Page 609

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 610

    First edition printed in u.S.A. Fca us llc ©2015 fca us llc. All rights reserved. Fiat is a registered trademark of fiat group marketing & corporate communication s.P.A., used under license by fca us llc. 16fb-126-aa.