1. DL manuals
  2. Fiat
  3. Automobile
  4. 2016 500X
  5. User Manual

Fiat 2016 500X User Manual

Other manuals for 2016 500X: Owner's Manual

Summary of 2016 500X

  • Page 1

    Download a free electronic copy of the owner’s manual or warranty booklet by visiting: www.Fiatusa.Com/en/owners/manuals (u.S.); www.Owners.Mopar.Ca/en (canada). 16fb-926-aa first edition user guide 2 01 6 user guide 1908679_16a_500x_ug_030515.Indd 1 3/5/15 2:17 pm.

  • Page 2

    If you are the first registered retail owner of your vehicle, you may obtain a complimentary printed copy of the owner’s manual, navigation/uconnect ® manuals or warranty booklet by calling 1-888-242-6342 (u.S.) or 1-800-387-1143 (canada) or by contacting your dealer. The driver’s primary responsibi...

  • Page 3

    Introduction/welcome welcome from fiat . . . . . . . . . . . . . . .2 controls at a glance driver cockpit . . . . . . . . . . . . . . . . . .4 instrument cluster . . . . . . . . . . . . . .6 getting started key fob . . . . . . . . . . . . . . . . . . . . . . .8 remote start . . . . . . . . . . . . ....

  • Page 4

    Welcome from fiat congratulations on selecting your new fiat vehicle. Be assured that it represents preci- sion workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. Your new fiat vehicle has characteristics to enhance the driver's control under so...

  • Page 5

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution (excluding legal lines). Warning! • pedals that cannot move freely can cause loss of vehicle control and increase the risk of serio...

  • Page 6

    Driver cockpit 1. Headlight switch pg. 36 2. Electronic vehicle information center (evic) controls pg. 117 3. Turn signal/light lever pg. 38 4. Speedometer pg. 6 5. Electronic vehicle information center (evic) pg. 117 6. Electronic speed control pg. 43 7. Tachometer pg. 6 8. Wiper/washer lever pg. 3...

  • Page 7

    11. Glove compartment 12. Climate controls pg. 46 13. Media hub – playing ipod/usb/mp3/aux devices pg. 77 14. Power outlet pg. 125 15. Shift lever 16. Heated seats — if equipped pg. 30 17. Power mirror switch 18. Power window switch 19. Power door locks controls at a glance 5.

  • Page 8

    Instrument cluster 1. Speedometer 2. Fuel gauge 3. Electronic vehicle information center (evic) (see page 130 for instrument cluster warning lights information.) controls at a glance 6.

  • Page 9

    4. Temperature gauge 5. Tachometer (see page 136 for instrument cluster indicator lights information.) controls at a glance 7.

  • Page 10

    Key fob • this feature allows the driver to operate the ignition switch with the push of a button as long as the remote keyless entry (rke) transmitter is in the passen- ger compartment. • the keyless push button ignition has three operating positions. The three po- sitions are off, on/run and start...

  • Page 11

    Note: in case the ignition switch does not change with the push of a button, the rke transmit- ter (key fob) may have a low or dead battery. In this situation, a back up method can be used to operate the ignition switch. Put the nose side (side opposite of the emergency key) of the key fob against t...

  • Page 12

    • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or th...

  • Page 13

    Vehicle security alarm the vehicle security alarm monitors the vehicle doors for unauthorized entry and the keyless enter-n-go start/stop button for unauthorized operation. While the vehicle security alarm is armed, interior switches for door locks and decklid release are disabled. If something trig...

  • Page 14

    Keyless enter-n-go the keyless enter-n-go system is an enhancement to the vehicle’s remote keyless entry (rke) feature. This feature allows you to lock and unlock the vehicle's door(s) and liftgate without having to push the key fob lock or unlock buttons, as well as starting and stopping the vehicl...

  • Page 15

    To lock the vehicle: • both front door handles have buttons located on the outside of the handle. With one of the vehicle’s keyless enter-n-go key fobs located outside the vehicle and within 5 ft (1.5m) of the driver's or passenger front door handle, push the door handle but- ton to lock all four do...

  • Page 16

    Lock or unlock the liftgate to lock the liftgate with a valid passive entry rke transmitter within 5 ft (1.5 m) of the liftgate, push passive entry lock button located to the right of passive entry liftgate unlock/release button. To unlock/enter the liftgate the liftgate passive entry unlock feature...

  • Page 17

    Stopping 1. Place the shift lever in park. 2. Push the engine start/stop button once. The ignition switch will return to the off position. Note: if the shift lever is not in park, the engine start/stop button must be held for two seconds and vehicle speed must be above 5 mph (8 km/h) before the engi...

  • Page 18

    Seat belt systems lap/shoulder belts • all seating positions in your vehicle are equipped with lap/shoulder belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. • position the lap belt so that it is snug and lies low across your hips, below your abdo- men. To remove...

  • Page 19

    Supplemental restraint system (srs) — air bags air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • knee impact bolsters • advanced front air...

  • Page 20

    • if it is necessary to modify the air bag system for persons with disabilities, contact your authorized dealer. • refer to the owner's manual on the dvd for further details regarding the supple- mental restraint system (srs). Supplemental knee air bags this vehicle is equipped with a supplemental d...

  • Page 21

    Warning! • side air bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • being too close to the side air bags during deployment could cause you to be severely injured or killed. • relying on the side air bags alone could lead to more severe inju...

  • Page 22

    Enhanced accident response system reset procedure after the event occurs, when the system is active, a message regarding fuel cutoff is dis- played. Turn the ignition switch from ignition avv/start or mar/acc/on/run to igni- tion stop/off/lock. Carefully check the vehicle for fuel leaks in the engin...

  • Page 23

    Air bag warning light • the air bags must be ready to inflate for your protection in a collision. The occupant restraint controller (orc) monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. • the orc monitors the readiness of the electronic...

  • Page 24

    Note: edr data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the edr under normal driving conditions and no personal data (e.G., name, gender, age, and crash location) are recorded. However, other parties, such as law enforcement, could combine th...

  • Page 25

    Locating latch anchorages the lower anchorages are round bars that are found at the rear of the seat cush- ion where it meets the seatback, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint.You will easily feel them if ...

  • Page 26

    3. If the child restraint has a tether strap, connect it to the top tether anchorage. See below for directions to attach a tether anchor. 4. Tighten all of the straps as you push the child restraint rearward and downward into the seat. Remove slack in the straps according to the child restraint manu...

  • Page 27

    Installing the top tether strap (with either lower anchors or vehicle seat belt): when installing a forward-facing child restraint, always secure the top tether strap, up to the tether anchor weight limit, whether the child restraint is installed with the lower an- chors or the vehicle seat belt. Te...

  • Page 28

    Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. Warning! The head restraints for all occupants must be ...

  • Page 29

    Rear head restraints your vehicle is equipped with two outboard head restraints and one center head re- straint for its rear passengers. The rear head restraints can be raised or lowered. When the center seat is being occupied, the head restraint should be in the raised position. When there are no o...

  • Page 30

    Manual front seats manual front seat forward/rearward ad- justment on models equipped with manual seats, the forward/rearward adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once ...

  • Page 31

    Power adjustment (front) — if equipped the power seat controls are located on the outboard side of the seat, close to the floor. Use the switch to move the seat up/down, forward/rearward, tilt if equipped and to set the angle of the seatback. Forward or rearward adjustment the seat can be adjusted b...

  • Page 32

    Heated seats — if equipped the heated seat switches are located on the instrument panel. You can choose between two heating levels: • push the heated seat button once to turn the hi setting on. • push the heated seat button a second time to turn the lo setting on. • push the heated seat button a thi...

  • Page 33

    Rear seats the split rear seat increases the storage of the rear cargo area. Note: prior to folding the rear seat down, it may be necessary to position the front seat to its mid-track position. Be sure that the front seats are fully upright and positioned forward, this will allow the rear seat to fo...

  • Page 34

    Cargo area enlargement folding both sides of the rear seat provides additional storage in the rear cargo area. Proceed as follows: 1. Remove the rear shelf (if equipped). 2. Fully lower the rear seat head restraints. 3. Move the safety belts to the outboard side of the seat. 4. Pull the seatback rel...

  • Page 35

    Steering wheel tilt/telescoping steering column this feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located be- low the steering wheel at the end of the steering column. To unlock the ste...

  • Page 36

    Heated steering wheel — if equipped the steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel switch has been turned on, it will operate for up to 80 minutes before automaticall...

  • Page 37

    Engine break-in recommendations a long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While crui...

  • Page 38

    Exterior lights headlights the headlight switch is located on the left side of the instrument panel. The headlight switch controls the operation of the headlights, side marker lights, daytime running lights, fog lights and the dimming of the instrument cluster and interior lighting. Turning on the h...

  • Page 39

    Front fog lights — if equipped the front fog light switch is built into the headlight switch. To activate the front fog lights, turn on the parking lights or the low beam headlights and push the headlight switch. To turn off the front fog lights, push the headlight switch a sec- ond time or turn off...

  • Page 40

    High beams to turn on the high beam headlights, push the turn signal lever forward (toward the front of the vehicle) and an indicator will illuminate in the cluster. To turn off the high beams, pull the turn signal lever rearward (toward the rear of the vehicle). Note: the headlights must be on for ...

  • Page 41

    Wipers and washers front wiper operation the windshield wiper/washer controls are located on the lever on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. Caution! Always remove any buildup of snow that prevents the windshiel...

  • Page 42

    Windshield washer operation to use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the lever is released, and then resume the intermittent interval previ...

  • Page 43

    • use of rain-x or products containing wax or silicone may reduce rain sensing perfor- mance. • the rain sensing feature can be turned on and off using the uconnect system, refer to “uconnect settings” in “multimedia” for further information. The rain sensing system has protection features for the w...

  • Page 44

    Rear window defroster the rear window defroster button is located with the climate controls on the instru- ment panel. Push this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns...

  • Page 45

    Speed control when engaged, the speed control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the speed control system has been designed to shut down i...

  • Page 46

    Deactivation a soft tap on the brake pedal, pushing the cancel button, esc intervention, forward collision mitigation, electronic park brake intervention, or normal brake pressure while slowing the vehicle will deactivate the speed control without erasing the set speed from memory. Pushing the on/of...

  • Page 47

    Metric speed (km/h) • pushing the set - button once will result in a 1 km/h decrease in set speed. Each sub- sequent tap of the button results in a decrease of 1 km/h. • if the button is continually pushed, the speed will continue to decrease until the button is released, then the new set speed will...

  • Page 48

    Heated mirrors • the mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Automatic temperature controls (atc) automatic operation • push the auto button. • select the desired temperature by rotating temperature control knobs. • the syste...

  • Page 49

    Air recirculation • use recirculation for maximum a/c operation. • for window defogging, turn the recirculation off. • recirculation is not allowed in defrost, floor, defrost/floor (mix) modes. Max defrost • push the max defrost button to change the current airflow setting to defrost mode. Performin...

  • Page 50

    Electric park brake (epb) your vehicle is equipped with a new electric park brake system (epb) that offers greater convenience. The epb switch is located in the center console. To apply the park brake manually, pull up on the switch momentarily. The brake warning lamp in the instrument cluster and a...

  • Page 51

    Caution! If the brake system warning light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. Warning! • never use the park position as a substitute for the parking brake. Always apply the parking b...

  • Page 52

    Dynamic selector — if equipped the dynamic selector combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance in all driving conditions. The dynamic selector consists of the fol- lowing positions: auto mode – this mode is designed for comfort ...

  • Page 53

    The bsm detection zone covers approximately one lane width on both sides of the ve- hicle, 10 ft (3 m). The zone length starts at the outside mirror and extends approximately 20 ft (6 m) beyond the rear bumper of the vehicle. The bsm system monitors the de- tection zones on both sides of the vehicle...

  • Page 54

    Warning! The blind spot monitoring system is only an aid to help detect objects in the blind spot zones. The bsm system is not designed to detect pedestrians, bicyclists, or animals. Even if your vehicle is equipped with the bsm system, always check your vehicles mirrors, glance over your shoulder, ...

  • Page 55

    Mode of operation three selectable modes of operation are available in the uconnect system. Refer to “uconnect settings” in “multimedia” in your owner’s manual on the dvd for further information. Blind spot alert lights only when operating in blind spot alert mode, the bsm system will provide a visu...

  • Page 56

    System not available in the case of the system being temporary unavailable: • bsm mirror warning lights are turned on continuously. • a instrument cluster message will display “blind spot monitoring temporary unavailable.” in the case of the system being completely unavailable: • a chime will turn o...

  • Page 57

    Vehicles with automatic transmission: after the end of the intervention of automatic braking, the transmission may remain in last gear stored: therefore the car could lurch forward, once the brakes release a few seconds later. If the brake control event stops the vehicle completely, the system will ...

  • Page 58

    Turning brake control on or off the brake control menu setting is located in the uconnect settings. Note: the default status of brake control is “warning + active braking,” this allows the system to warn you of a possible collision with the vehicle in front of you and enable the active braking. • ch...

  • Page 59

    Brake control limited warning if the evic displays “brake control limited functionality” or “brake control limited functionality clean front windshield” momentarily, there may be a condition that limits brake control functionality. Although the vehicle is still drivable under normal conditions, the ...

  • Page 60

    Precautions while driving with brake control in certain driving conditions, such as: • driving in the vicinity of a curve • small vehicles and/or not aligned to the lane • lane changing of other vehicles • passing of vehicles in an oncoming intersection the intervention of the system could be unexpe...

  • Page 61

    Lanesense — if equipped lanesense operation the lanesense system is operational at speeds above 37 mph (60 km/h) and below 112 mph (180 km/h). The lanesense system uses a forward looking camera to detect lane markings and measure vehicle position within the lane boundaries. When both lane markings a...

  • Page 62

    Turning lanesense on or off the default status of lanesense is “off”. The lanesense button is located on the end of the turn signal stalk located on the steer- ing column. To turn the lanesense system on, push the lane assist button (led turns off). A “lane sense on” message is shown in the evic. To...

  • Page 63

    Left lane departure — both lanes detected • when the lanesense system is on, the lane lines turn from gray to white to indicate that both of the lane markings have been detected. The lanesense indicator is solid green when both lane markings have been detected and the system is “armed” to pro- vide ...

  • Page 64

    Parksense rear park assist — if equipped the parksense rear park assist system provides visual and audible indications of the dis- tance between the rear fascia and a detected obstacle when backing up, e.G. During a parking maneuver. Parksense will retain the last system state (enabled or disabled) ...

  • Page 65

    Instrument cluster display parksense is displayed on the instrument cluster only if you have selected the item "sound and display" inside the "settings" menu of the uconnect system. If an obstacle is detected in the center rear region, the display will show a single solid arc in the center rear regi...

  • Page 66

    Service the rear park assist system during vehicle start up, when the parksense rear park assist system has detected a faulted condition, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the “park assist unavailable wipe rear sensors” or the “park assi...

  • Page 67

    Caution! • rear park assist is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not de- tected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • the v...

  • Page 68

    Parkview rear back up camera — if equipped the parkview rear back up camera that allows you to see an on-screen image of your vehicle's rear surroundings when the shift lever is put into reverse. The image will be displayed on the touchscreen display along with a note to “check entire surroundings” ...

  • Page 69

    Warning! Drivers must be careful when backing up even when using the parkview rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestri- ans, animals, other vehicles, obstructions, or blind spots before backing up.You are re- sponsible for the safety of your ...

  • Page 70

    Your vehicle's sound system 1. Uconnect phone button pg. 106 2. Uconnect voice command button pg. 113 3. Phone hang up button 4. Left steering wheel audio controls (located behind the steering wheel) pg. 117 5. Right steering wheel audio controls (located behind the steering wheel) pg. 117 6. Volume...

  • Page 71

    7. Uconnect 5.0 radio pg. 74 8. Settings button 124 9. Tune/scroll knob – browse/enter button 10. Aux jack pg. 77 11. Usb port pg. 77 12. Front power outlet pg. 125 electronics 69.

  • Page 72

    Identifying your radio uconnect 3.0 • 3.0” display • three buttons on the faceplate on either side of the display uconnect 5.0 • 5.0” full color touchscreen display • bluetooth connectivity/bluetooth streaming audio uconnect 6.5an • 6.5” full color touchscreen display • hd radio button visible on ri...

  • Page 73

    Uconnect access via mobile uconnect access via mobile, which uses the uconnect access app and you smartphone’s data plan to access your personal pandora, iheartradio and slacker accounts from the vehicle and enable their control using the touchscreen, is a late availability feature.Visit driveuconne...

  • Page 74

    Clock setting 1. Push the menu button at the bottom of the radio, and push the enter/browse button for system settings. Next, select the time and format setting and then select set time by pushing the enter/browse button. 2. Adjust the hours or minutes by turning the tune/scroll knob, then pushing t...

  • Page 75

    Usb/audio jack (aux) manual operation to select a specific audio source, push the media button on the faceplate. To allow mu- sic to play from your portable device through the vehicle’s speakers, push the media button repeatedly to select one of the following modes: usb/ipod • usb/ipod mode is enter...

  • Page 76

    Uconnect 5.0 note: do not attach any object to the touchscreen, doing so can result in damage to the touchscreen. Clock setting to start the clock setting procedure: 1. Push the settings button on the faceplate and then press the “clock and date” button on the touchscreen. 2. Press the “set time” bu...

  • Page 77

    3. Press the “up” or “down” arrows to adjust the hours or minutes, then select the “am” or “pm” button on the touchscreen.You can also select 12hr or 24hr format by pressing the desired button on the touchscreen. 4. Once the time is set press the “done” button on the touchscreen to exit the time scr...

  • Page 78

    Radio operation store radio presets manually the radio stores up to 12 presets in each of the radio modes. There are four visible presets at the top of the radio screen. Pressing the “all” button on the touchscreen on the radio home screen will display all of the preset stations for that mode. To st...

  • Page 79

    Siriusxm premier over 160 channels get every channel available on your satellite radio, and enjoy all you want, all in one place. Hear commercial-free music plus sports, news, talk and entertainment. Get all the pre- mium programming, including howard stern, every nfl game, oprah radio, every mlb an...

  • Page 80

    Audio jack (aux) the aux jack allows a portable device, such as an mp3 player or an ipod, to be plugged into the radio and utilize the vehicle’s audio system, using a 3.5 mm audio cable, to am- plify the source and play through the vehicle speakers. • push the media button on the faceplate, press th...

  • Page 81

    Voice text reply (not compatible with iphone) once your uconnect system is paired with a compatible mobile device, the system can announce a new incoming text message, and read it to your over the vehicle audio sys- tem.You can reply to the message using voice recognition by selecting, or saying, on...

  • Page 82

    Uconnect 5.0 voice recognition quick tips introducing uconnect start using uconnect voice recognition with these helpful quick tips. It provides the key voice commands and tips you need to know to control your uconnect 5.0 system. Key features: • five-inch color touchscreen display with am/fm/usb/bl...

  • Page 83

    Get started 1. Visit uconnectphone.Com to check mobile device and feature compatibility and to find phone pairing instructions. 2. Reduce background noise. Wind and passenger conversations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing st...

  • Page 84

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect system. Push the vr button . After the beep, say: • cancel to stop a current voice session • help to hear a list of suggested voice commands • repeat to listen to the system prompts again notice t...

  • Page 85

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio stations you would like to hear. (subscription or included siriusxm satellite radio trial required.) push the vr button . After the beep, say: • tune to ninety-five-point-five fm • tune to satellite channel hits 1 tip at a...

  • Page 86

    Media push the vr button . After the beep, say one of the following commands and follow the prompts to switch your media source or choose an artist. • change source to bluetooth • change source to ipod • change source to usb • play artist beethoven; play album greatest hits; play song moonlight sona...

  • Page 87

    Phone making and answering hands-free phone calls is easy with uconnect. When the phone- book button is illuminated on your touchscreen, your system is ready. U.S./canadian residents can visit • uconnectphone.Com to check mobile device and feature compatibility and to find phone pairing instructions...

  • Page 88

    Additional information © 2015 fca us llc. All rights reserved. Mopar, mopar owner connect and uconnect are registered trademarks of fca us llc. Android is a trademark of google inc. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc.Yelp,yelp logo,yelp burst and related ma...

  • Page 89

    Uconnect 6.5an at a glance displaying the time • if the time is not currently displayed on the radio or player main page press the set- tings button. In the settings list, press the “clock” button on the touchscreen then press “on” or “off” for show time in status bar. Uconnect 6.5an radio 1 — displ...

  • Page 90

    Setting the time model 6.5an synchronizes time automatically via gps, so should not require any time adjustment. If you do need to set the time manually, follow the instructions below. • for model 6.5an, turn the unit on, then press the time display at the top of the screen, a pop-up will ask if you...

  • Page 91

    Radio • to access the radio mode, press the radio button below the screen. Selecting radio stations • press the desired radio band (am, fm or sxm) button. Seek next/seek previous • press the up or down “seek arrow” buttons on the touchscreen for less than two seconds to seek through radio stations. ...

  • Page 92

    Store radio presets manually your radio can store 36 total preset stations, 12 presets per band (am, fm and sxm). They are shown at the top of your radio screen. To see the 12 preset stations per band, press the “arrow” button on the touchscreen at the top right of the screen to toggle between the t...

  • Page 93

    Siriusxm parental controls • you can skip or hide certain channels from view if you do not want access to them. Push the settings button on the faceplate, press the “siriusxm setup” button on the touchscreen, then select channel skip. Press the box, check-mark, next to the channel you want skipped. ...

  • Page 94

    Replay option option description replay time displays the amount of time in the upper center of the screen by which your content lags the live channel. Live resumes playback of live content at any time while replaying rewound content. • siriusxm services require subscriptions, sold separately after ...

  • Page 95

    Usb port connect your ipod or compatible device using a usb cable into the usb port. Usb memory sticks with audio files can also be used. Then, audio from the device can be played on the vehicles sound system while providing metadata (artist, track title, album, etc.) information on the radio displa...

  • Page 96

    Bluetooth streaming audio if equipped with uconnect voice command, your bluetooth-equipped ipod devices, cell phones or other media players, may also be able to stream music to your vehicle's sound system.Your connected device must be bluetooth-compatible, and paired with your sys- tem (see uconnect...

  • Page 97

    Note: uconnect will usually automatically switch to the appropriate mode when something is first connected or inserted into the system. Uconnect 6.5an navigation • press the nav button to access the navigation feature. Changing the navigation voice prompt volume 1. Press the "settings" button on the...

  • Page 98

    Finding points of interest • from the main navigation menu, press the “where to?” button on the touchscreen, then press the “point of interest” button on the touchscreen. • select a category and then a subcategory, if necessary. • select your destination and press the “yes” button on the touchscreen...

  • Page 99

    Go home a home location must be saved in the system. • from the main navigation menu, press the “where to?” button on the touchscreen, then press the “go home” button on the touchscreen. • your route is marked with a blue line on the map. If you depart from the original route, your route is recalcul...

  • Page 100

    Taking a detour to take a detour you must be navigating a route: • press the “detour” button on the touchscreen. Note: if the route you are currently taking is the only reasonable option, the device might not calculate a detour. • for more information, see your uconnect 6.5an owner’s manual suppleme...

  • Page 101

    Get started 1. Visit uconnectphone.Com to check mobile device and feature compatibility and to find phone pairing instructions. 2. Reduce background noise. Wind and passenger conversations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing st...

  • Page 102

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect system. Push the vr button . After the beep, say: • cancel to stop a current voice session • help to hear a list of suggested voice commands • repeat to listen to the system prompts again notice t...

  • Page 103

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio stations you would like to hear. (subscription or included siriusxm satellite radio trial required.) push the vr button . After the beep, say: • tune to ninety-five-point-five fm • tune to satellite channel hits 1 tip at a...

  • Page 104

    Media uconnect offers connections via usb, bluetooth and auxiliary ports (if equipped).Voice operation is only available for connected usb and ipod devices. (cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands and follow the p...

  • Page 105

    Phone making and answering hands-free phone calls is easy with uconnect. When the phone- book button is illuminated on your touchscreen, your system is ready. U.S./canadian residents can visit: • uconnectphone.Com to check mobile device and feature compatibility and to find phone pairing instruction...

  • Page 106

    Navigation (6.5an) the uconnect navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. 1. To enter a destination, push the vr button . After the beep, say: • navigate to 800 chrysler drive auburn hills, michigan. 2. Then follow the...

  • Page 107

    Siriusxm travel link (6.5an — us market only) need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? Siriusxm travel link is a suite of services that brings a wealth of infor- mation right to your uconnect 6.5an system. Push the vr button . After...

  • Page 108

    Uconnect system support: • driveuconnect.Com • u.S residents call: 1-877-855-8400 • canadian residents call: 1-800-465-2001 (english) or 1-800-387-9983 (french) mon. – fri., 7:00 am – 12:00 am, et sat., 8:00 am – 10:00 pm, et sun., 9:00 am – 5:00 pm, et uconnect phone uconnect phone (bluetooth hands...

  • Page 109

    The uconnect phone feature enables you to place and receive hands-free mobile phone calls. Drivers can also place mobile phone calls using their voice or by using the buttons on the touchscreen (see voice command section). The hands-free calling feature is made possible through bluetooth technology ...

  • Page 110

    Note: • the uconnect phone requires a mobile phone equipped with the bluetooth hands- free profile,version 1.0 or higher. • most mobile phones/devices are compatible with the uconnect system, however some mobile phones/devices may not be equipped with all of the required features to utilize all of t...

  • Page 111

    5. If no is selected, and you still would like to pair a mobile phone, press the “settings” button from the uconnect phone main screen. • select “paired phones” then press the “add device” button on the touchscreen. • search for available devices on your bluetooth enabled mobile phone (see below). W...

  • Page 112

    Uconnect 6.5: 1. Place the ignition in the acc or on position. 2. Press the “phone” button in the menu bar on the touchscreen. 3. Select “settings.” 4. Select “paired phones.” 5. Select “add device.” • uconnect phone will display an “in progress” screen while the system is connecting. Pair your ipho...

  • Page 113

    Select the iphone's priority level when the pairing process has successfully completed, the system will prompt you to choose whether or not this is your favorite mobile phone. Selecting “yes” will make this mobile phone the highest priority. This mobile phone will take precedence over other paired m...

  • Page 114

    Select the android mobile phone's priority level when the pairing process has successfully completed, the system will prompt you to choose whether or not this is your favorite mobile phone. Selecting “yes” will make this mobile phone the highest priority. This mobile phone will take precedence over ...

  • Page 115

    Voice command tips • speaking complete names (i.E; call john doe vs. Call john) will result in greater system accuracy. • you can “link” commands together for faster results. Say “call john doe, mobile,” for example. • if you are listening to available voice command options, you do not have to liste...

  • Page 116

    Iphone 1. Press the settings button on the mobile phone. 2. Select bluetooth. • ensure bluetooth is enabled, and the mobile phone is paired to the uconnect system. 3. Select located under devices next to uconnect. 4. Turn “show notifications” to on. Android devices 1. Push the menu button on the mob...

  • Page 117

    Voice text reply (not compatible with iphone) note: voice texting reply and voice texting features require a compatible mobile device enabled with bluetooth message access profile (map). Iphone, and some other smartphones, may not entirely support bluetooth map.Visit uconnectphone.Com for the latest...

  • Page 118

    Helpful tips and common questions to improve bluetooth performance with your uconnect system mobile phone won’t reconnect to system after pairing: • set mobile phone to auto-connect or trusted device in mobile phone bluetooth set- tings (blackberry devices). • perform a factory reset on your mobile ...

  • Page 119

    Steering wheel audio controls the steering wheel audio controls are located on the rear surface of the steering wheel. Right switch • push the switch up or down to increase or decrease the volume. • push the button in the center to change modes am/fm/cd/sxm/aux or usb port. Left switch • push the sw...

  • Page 120

    • push the back/left button to access the information screens or submenu screens of a main menu item. • push the ok button to access/select the information screens or submenu screens of a main menu item. Push and hold the ok arrow button for two seconds to reset displayed/selected features that can ...

  • Page 121

    Vehicle info (information about the status of the car) push and release the up or down arrow button until "vehicle info" is highlighted in the evic. Push and release the right arrow button and coolant temp will be displayed. Push the right or left arrow button to scroll through the following informa...

  • Page 122

    • average consumption • (mpg, or l/ 100km or km/l) • travel time • (hour/minute) audio (viewing audio information) this menu item allows you to view the instrument cluster display and the information present on the display of the uconnect system. The information displayed is: • “radio (am or fm)” • ...

  • Page 123

    • "full pnrd" • (default): the right side of the display the letters pnrd, the position assumed by the shift lever will be highlighted in the display. During the operation in sequential mode ("autostick"), in place of the letter d, the gear will be will be displayed. In the top left/top right the in...

  • Page 124

    “display” by selecting the "display," you can access the following settings: • language: allows you to select the language in which to display the information/ warnings. • see phone: allows you to view, on the instrument cluster display, the information relat- ing to phone mode displayed on the disp...

  • Page 125

    "safety & assistance" by selecting the item "safety & assistance," you can make the following adjustments: • fcw: a selection of operating modes of the system forward collision warning plus • fcw sensitivity: a selection of the "readiness" of intervention of the forward collision warning plus system...

  • Page 126

    "doors & safety" by selecting the item "doors & safety," you can make the following adjustments: • auto door lock: activation/deactivation of the automatic locking of the doors with the vehicle moving • auto unlock on exit: automatic unlocking of the doors when exiting the vehicle • flash light with...

  • Page 127

    Power outlet there is one 12 volt (13 amp) power outlet in this vehicle, located under the hvac controls. This power outlet can power mobile phones, electronics and other low power devices. • this power outlet is located in front of the shift lever. Note: • do not exceed the maximum power of 160 wat...

  • Page 128

    Cargo area features cargo load floor — if equipped the vehicle is equipped with a load floor that can be adjusted as needed. Position 1 (floor flush): this position allows you to make the load floor flat for ease of loading/unloading objects from the cargo area. This position also makes it possible ...

  • Page 129

    Anchoring of the load the cargo tie-downs, located on the trim panels around the cargo area floor, should be used to safely secure loads when the vehicle is moving. Cargo box — if equipped the cargo area contains a preformed cargo box that can be used for the storage of ob- jects that allows you to ...

  • Page 130

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle front wheel drive (fwd) all-wheel drive (awd) towing condition wheels off the ground automatic transmission manual transmission manual/ automatic transmis- sion flat tow none not allowed not allowed not allowed d...

  • Page 131

    • properly secure the front wheels to the dolly, following the dolly manufacturer's in- structions. • turn the ignition to the mar/run position, but do not start the engine. • press and hold the brake pedal. • release the electric park brake (epb). • place the ignition in the off position, remove th...

  • Page 132

    Roadside assistance • if your fiat 500x requires jump start assistance, out of gas/fuel delivery, tire service, lockout service or towing due to a defect covered under the basic limited warranty, dial toll-free 1-888-242-6342 or 1-800-363-4869 for canadian residents. See your warranty booklet for fu...

  • Page 133

    If the abs light is on, the brake system should be serviced as soon as possible to restore the benefits of anti-lock brakes. If the abs light does not turn on when the ignition switch is turned to the mar/run position, have the light inspected by an authorized dealer. - air bag warning light this li...

  • Page 134

    Note: after inflation, the vehicle may need to be driven for 20 minutes before the flashing light will turn off. Please note that the tpms is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached...

  • Page 135

    Warning! A hot engine cooling system is dangerous.You or others could be badly burned by steam or boiling coolant. -transmission temperature warning light this light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing. If this li...

  • Page 136

    If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the brake booster has been detected by the anti-lock brake system (abs)/elec...

  • Page 137

    - malfunction indicator light (mil) the malfunction indicator light (mil) is part of an onboard diagnostic system called obd ii that monitors engine and automatic transmission control systems. The light will illuminate when the key is in the mar/run position before engine start. If the bulb does not...

  • Page 138

    Instrument cluster indicator lights - turn signal indicator the arrows will flash with the exterior turn signals when the turn signal lever is oper- ated. A tone will chime, and a evic message will appear if either turn signal is left on for more than 1 mile (1.6 km). Note: if either indicator flash...

  • Page 139

    - forward collision warning (fcw) off indicator note: • the default status of fcw is “on.” this allows the system to warn you of a possible collision with the vehicle in front of you. • the forward collision button is located on the switch panel below the uconnect display. • to turn the fcw system o...

  • Page 140

    If your engine overheats in any of the following situations, you can reduce the potential for overheating your en- gine by taking the appropriate action. • on the highways — slow down. • in city traffic — while stopped, put transmission in neutral, but do not increase en- gine idle speed. Caution! D...

  • Page 141

    Tire service kit storage the tire service kit is located in the rear storage compartment inside a storage con- tainer. Located inside the container are a screwdriver and the emergency fuel funnel. To access the tire service kit open the lift gate and remove the load floor. Tire service kit — if equi...

  • Page 142

    Warning! • do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the tire service kit. • do not use tire service kit or drive the vehicle under the following circumstances: • if the puncture in the tire t...

  • Page 143

    Warning! Tire service kit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using tire service kit. Do not exceed 65 mph (110 km/h) until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you...

  • Page 144

    Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehicle could slip...

  • Page 145

    2. Lift the access cover using the load floor handle. 3. Remove the fastener securing the spare tire. Load floor handle spare tire fastener what to do in emergencies 143.

  • Page 146

    4. Remove the jack, wheel bolt wrench, and wheel chocks. 5. Remove the spare tire. Warning! A loose tire or jack thrown forward in a collision or hard stop could endanger the oc- cupants of the vehicle. Always stow the jack parts and the spare tire in the places pro- vided. Have the deflated (flat) ...

  • Page 147

    Preparations for jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as pos- sible. Avoid icy or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when opera...

  • Page 148

    Jacking instructions warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as pos- sible before raising the vehicle. • turn on the hazard warning flasher. • chock th...

  • Page 149

    4. Place the jack underneath the lift area that is closest to the flat tire. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, centering the jack saddle inside the cutout in the sill cladding. Jacking locations 1 — front jacking location 2 — rear j...

  • Page 150

    Front jacking engagement point rear jacking location rear jacking engagement point what to do in emergencies 148.

  • Page 151

    5. Raise the vehicle just enough to remove the flat tire. Warning! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire. 7. Mount the spare...

  • Page 152

    9. Lower the vehicle to the ground by turning the wheel bolt wrench counterclockwise. 10. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the wheel bolts in a star pattern until each wheel bolt has been tightened twice. The co...

  • Page 153

    Jump starting if your vehicle has a discharged battery it can be jump-started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump starting can be dangerous if done improperly so please follow the procedures in this sec- tion carefully. Note...

  • Page 154

    Preparations for jump start the battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. Note: the positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post. Warning! • take care to avo...

  • Page 155

    Warning! Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. Jump starting procedure warning! Failure to follow this jump-starting procedure could result in personal injury or prop- erty damage due to battery explosion. Caution! Fai...

  • Page 156

    6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the jumper cable from the engine ground of the vehicle with the discharged battery. 2. Disconnect the opposite end of the negative (-) jumper cable f...

  • Page 157

    For vehicles with automatic transmission: shifts between drive and reverse can only be achieved at wheel speeds of 5 mph (8 km/h) or less. Whenever the transmission remains in neutral for more than two seconds, you must push the brake pedal to engage drive or reverse. Note: push the "esc off" switch...

  • Page 158

    Tow eye usage — if equipped your vehicle is equipped with a tow eye that can be used to tow a disabled vehicle. When using a tow eye be sure to follow the “tow eye usage precautions” and the “tow- ing a disabled vehicle” instructions in this section. Tow eye usage precautions note: • ensure that the...

  • Page 159

    Caution! • the tow eye must be used exclusively for roadside assistance operations. Only use the tow eye with an appropriate device in accordance with the highway code (a rigid bar or rope) to flat tow the vehicle for a short distance to the nearest ser- vice location. • tow eyes must not be used to...

  • Page 160

    Rear tow eye installation the rear tow eye receptacle is located behind a access door on the rear bumper fascia. To install the tow eye, open the access door using the vehicle key or a small screwdriver, and thread the tow eye into the receptacle. Insert the wheel bolt wrench handle through the eye ...

  • Page 161

    5. Insert a small screwdriver or similar tool down into the shift lever override access hole (at the right front corner of the shift lever assembly), and push and hold the override release lever down. 6. Move the shift lever to the neutral position. 7. The vehicle may then be started in neutral. 8. ...

  • Page 162

    Note: • you must ensure that the auto park brake feature is disabled before towing this vehicle, to avoid inadvertent electric park brake engagement. The auto park brake feature is enabled or disabled via the customer programmable features in the uconnect settings. • vehicles with a discharged batte...

  • Page 163

    All wheel drive (awd) models the manufacturer requires towing with all four wheels off the ground. Acceptable methods are to tow the vehicle on a flatbed, or with one end of the vehicle raised and the opposite end on a towing dolly. Caution! • do not tow this vehicle with any of its wheels on the gr...

  • Page 164

    Hood opening the hood release lever (to open the primary latch) and safety latch (to open the second- ary latch) must be released to open the hood. 1. Pull the hood release lever located under the drivers side of the instrument panel. 2. Move to the outside of the vehicle. 3. Push the safety latch r...

  • Page 165

    Closing 1. Hold up the hood with one hand and with the other hand remove the support rod from its seat and reinsert it into the locking tab. 2. Lower the hood to approximately 6 inches (15 cm) from the engine compartment and drop it. Make sure that the hood is completely closed. Caution! To prevent ...

  • Page 166

    Engine compartment — 1.4l turbo 1. Engine air filter 2. Engine oil dipstick 3. Engine oil fill 4. Brake fluid reservoir maintaining your vehicle 164.

  • Page 167

    5. Battery 6. Power distribution center (fuses) 7. Washer fluid reservoir 8. Engine coolant reservoir maintaining your vehicle 165.

  • Page 168

    Engine compartment — 2.4l 1. Engine air filter 2. Engine oil dipstick 3. Engine oil fill 4. Brake fluid reservoir maintaining your vehicle 166.

  • Page 169

    5. Battery 6. Power distribution center (fuses) 7. Washer fluid reservoir 8. Engine coolant reservoir maintaining your vehicle 167.

  • Page 170

    Fluid capacities u.S metric fuel (approximate) 1.4l turbo/2.4l engine 12.7 gallons 48 liters engine oil with filter 1.4l turbo engine (sae 5w-40 synthetic, api certified) 4.0 quarts 3.8 liters 2.4l engine (sae 0w-20, api certified) 5.5 quarts 5.2 liters cooling system * 1.4l turbo engine (mopar anti...

  • Page 171

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped we recommend you use mopar c se- ries manual & dual dry clutch transmis- sion fluid. Automatic transmission – if equipped use only mopar zf 8&9 speed atf au- tomatic transmission fluid, or equivalent. Failure to us...

  • Page 172

    Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “electronic vehicle information center...

  • Page 173

    Maint enance char t mileage or time passed (whiche ver comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilomet ers 16,000 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,00...

  • Page 174

    Mileage or time passed (whiche ver comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilomet ers 16,000 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 19...

  • Page 175

    Mileage or time passed (whiche ver comes first) 10,000 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 years 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilomet ers 16,000 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 19...

  • Page 176

    (**) the spark plug change is dis tance based onl y, yearl y int er vals do not appl y. The follo wing ar e essential to ensur e cor rec t opera tion and pr ev ent serious damage to the engine: • onl y use spark plugs of the same mak e and type which ar e speciall y cer tif ied for such engines (r e...

  • Page 177

    Maintenance record odomet er da te signa tur e, aut horiz ed ser vice cent er 10,000 miles (16,000 km) or 1 years 20,000 miles (32,000 km) or 2 years 30,000 miles (48,000 km) or 3 years 40,000 miles (64,000 km) or 4 years 50,000 miles (80,000 km) or 5 years 60,000 miles (96,000 km) or 6 years 70,000...

  • Page 178

    Fuses warning! • when replacing a blown fuse, always use an appropriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material. Failure to use proper fuses may resu...

  • Page 179

    Cavity maxi fuse cartage fuse mini fuse description f01 70 amp tan – – module body computer f02 60 amp blue – – module body computer, rear distribution units f03 – 20 amp blue – controller power supply body computer f04 – 30 amp pink – brake control electron- ics module f05 70 amp tan – – electric p...

  • Page 180

    Cavity maxi fuse cartage fuse mini fuse description f87 – – 5 amp tan shift lever automatic transmission f88 – – 7.5 amp brown heated outside mirrors f89 – 30 amp pink – heated rear window f90 – – 5 amp tan ibs sensor (battery state of charge) body computer fuse center the controller is located at t...

  • Page 181

    Rear cargo fuse/relay distribution unit to access the fuses, remove the access door from the left rear panel of the rear cargo area. Push on the left side of the access door to unhinge and remove. Cavity mini fuse description f2 20 amp yellow audio system f3 20 amp yellow electric sunroof f5 30 amp ...

  • Page 182

    Emergency refueling procedure if the vehicle is out of fuel proceed as follows: 1. Open the liftgate and remove the emergency fuel fill funnel located in the cargo area. 2. Open the fuel door. 3. Insert the emergency fuel fill funnel in the filler pipe and proceed to fill the fuel tank. 4. Remove th...

  • Page 183

    Tire pressures check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle. The tire pressures recommended for your vehicle are found on the “tire and loading information” label located on the driver’s s...

  • Page 184

    Spare tires — if equipped note: for vehicles equipped with tire service kit instead of a spare tire, please refer to “tire service kit” in “what to do in emergencies” on your dvd for further information. Caution! Because of the reduced ground clearance, do not take your vehicle through an auto- mati...

  • Page 185

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the origi- nally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, th...

  • Page 186

    Bulb replacement interior bulbs lamps bulb number front courtesy light c5w front courtesy lights (sun visors) c5w rear dome light (models without retractable roof) c5w rear interior lights (models with retractable roof) c5w interior lights w5w dome light (glove box) w5w exterior bulbs lamps bulb num...

  • Page 187

    Fiat customer center p.O. Box 21–8004 auburn hills, mi 48321–8004 phone: 1-888-242-6342 fiat canada customer center p.O. Box 1621 windsor, ontario n9a 4h6 phone: 1-800-465-2001 (english) phone: 1-800-387-9983 (french) assistance for the hearing impaired to assist customers who have hearing difficult...

  • Page 188

    Reporting safety defects in the united states if you believe that your vehicle has a defect that could cause a collision or cause injury or death, you should immediately inform the national highway traffic safety administration (nhtsa) in addition to notifying the manufacturer. If nhtsa receives sim...

  • Page 189

    Authentic accessories by mopar • the following highlights just some of the many authentic fiat accessories by mopar featuring a fit, finish, and functionality specifically for your fiat 500x. • in choosing authentic accessories you gain far more than expressive style, pre- mium protection, or extrem...

  • Page 190

    Frequently asked questions getting started how do i install my latch equipped child seat? Pg. 23 electronics which radio is in my vehicle? • uconnect 3.0 pg. 71 • uconnect 5.0 pg. 74 • uconnect 6.5an pg. 87 how do i activate the audio jack? • uconnect 3.0 pg. 73 • uconnect 5.0 pg. 74 • uconnect 6.5a...

  • Page 191

    What to do in emergencies what do i do if my tpms warning light is blinking? Pg. 131 how do i change a flat tire? Pg. 142 how do i jump-start my vehicle? Pg. 151 maintaining your vehicle where is my fuse block located? Pg. 176 what type of oil do i use? Pg. 168 how often should i change my engine’s ...

  • Page 192

    Adding engine coolant (antifreeze) . . . .169 adding fuel. . . . . . . . . . . . . . . . .179 adding washer fluid . . . . . . . . . . . .169 air bag advanced front air bag . . . . . . . . .17 advance front air bag . . . . . . . . .17 air bags . . . . . . . . . . . . . . . . .17 air bag warning light...

  • Page 193

    Coolant level . . . . . . . . . . . . .169 disposal of used coolant . . . . . .169 drain, flush, and refill . . . . . . . . .169 inspection . . . . . . . . . . . . . . .169 points to remember . . . . . . . . .169 pressure cap . . . . . . . . . . . . .169 selection of coolant (antifreeze) . . . . . ....

  • Page 194

    High beam/low beam select (dimmer) switch . . . . . . . . . . . . . . . . . .38 hood prop . . . . . . . . . . . . . . . . .162 hood release . . . . . . . . . . . . . . .162 identifying your radio . . . . . . . . . . . .70 instrument cluster . . . . . . . . . . . . . .6 instrument cluster warning lig...

  • Page 195

    Programmable electronic features. . . . .124 radio presets . . . . . . . . . . . . . .72, 76, 89 radio operation. . . . . . . . . . . . . . .76 radio (sound systems) . . . . . . . . . . .76 rain sensitive wiper system . . . . . . . .40 rear camera . . . . . . . . . . . . . . . .66 rear cross path . ...

  • Page 196

    Wiper blade replacement . . . . . . . . .169 wipers, intermittent . . . . . . . . . . . . .39 wipers, rain sensitive . . . . . . . . . . . .40 wrecker towing . . . . . . . . . . . . . .159 index 194.

  • Page 197

    Notes 195.

  • Page 198

    Notes 196.

  • Page 199

    Notes 197.

  • Page 200

    Notes 198.

  • Page 201

    Notes 199.

  • Page 202

    Notes 200

  • Page 203

    If you are the first registered retail owner of your vehicle, you may obtain a complimentary printed copy of the owner’s manual, navigation/uconnect ® manuals or warranty booklet by calling 1-888-242-6342 (u.S.) or 1-800-387-1143 (canada) or by contacting your dealer. The driver’s primary responsibi...

  • Page 204

    Download a free electronic copy of the owner’s manual or warranty booklet by visiting: www.Fiatusa.Com/en/owners/manuals (u.S.); www.Owners.Mopar.Ca/en (canada). 16fb-926-aa first edition user guide 2 01 6 user guide 1908679_16a_500x_ug_030515.Indd 1 3/5/15 2:17 pm.