1. DL manuals
  2. Fiat
  3. Automobile
  4. 500L 2015
  5. Owner's Manual

Fiat 500L 2015 Owner's Manual

Other manuals for 500L 2015: User Manual

Summary of 500L 2015

  • Page 1

    O w n e r ’ s m a n u a l 2 0 1 5 2015 500l 15bf-126-ac third edition printed in u.S.A. 500l fca us llc.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name fca us llc shall be deemed to be deleted and the name fca canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability can be serious...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understa...

  • Page 5: Introduction

    Introduction contents ! Introduction . . . . . . . . . . . . . . . . . . . . . . . .4 ! How to use this manual . . . . . . . . . . . . . .5 ! Warnings and cautions . . . . . . . . . . . . . .7 ! Vehicle identification number . . . . . . . .7 ! Vehicle modifications/alterations . . . .8 1.

  • Page 6

    Introduction congratulations on selecting your new vehicle. Be as- sured that it represents precision workmanship, distinc- tive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and engineering spe...

  • Page 7

    How to use this manual consult the table of contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment. The detailed index ...

  • Page 8

    6 introduction.

  • Page 9

    Warnings and cautions this owner’s manual contains warnings against operating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owner’s manual, you may miss importan...

  • Page 10

    Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Stamped vin location 8 introduction.

  • Page 11: Contents

    Things to know before starting your vehicle contents ! A word about your keys . . . . . . . . . . . . .11 ▫ ignition switch . . . . . . . . . . . . . . . . . . . . . . . .11 ▫ locking doors with a key. . . . . . . . . . . . . . . .13 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .13 ! Sen...

  • Page 12

    ! Door locks . . . . . . . . . . . . . . . . . . . . . . . . .21 ▫ doors lock with one or more doors open . . .24 ▫ auto — relocking (only for rear doors) . . . . .24 ▫ child-protection door lock system — rear doors . . . . . . . . . . . . . . . . . . . . . . . . . .24 ▫ to engage or disengage the c...

  • Page 13

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key simply push the mechanical key release button. Note: the authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These number...

  • Page 14

    The ignition switch is fitted with a safety system that requires the ignition key to be turned back to stop if the engine does not start, before the starting operation can be repeated. Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park and re- move ...

  • Page 15

    Caution! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. Locking doors with a key you can insert the key with either side up. To lock the door, turn the key to the left. To unlock the door, turn the key ...

  • Page 16

    Caution! • always remove the sentry key® from the vehicle and lock all doors when leaving the vehicle unat- tended. • the sentry key® immobilizer system is not com- patible with some aftermarket remote starting sys- tems. Use of these systems may result in vehicle starting problems and loss of secur...

  • Page 17

    Vehicle security alarm the vehicle security alarm monitors the vehicle doors for unauthorized entry and the ignition switch for unau- thorized operation. While the vehicle security alarm is armed, interior switches for door locks and liftgate release are disabled. If something triggers the alarm, th...

  • Page 18

    If the vehicle security alarm sounds the horn a second time even when all doors, hood and liftgate are correctly closed, a fault has occurred in the operation of the system. Contact your authorized dealer. To disarm the system push unlock on the rke transmitter, or insert the key into the ignition s...

  • Page 19

    We recommend that you activate the safe lock device each time you park your car. Activating the safe lock device the safe lock device is enabled on all the doors by quickly double-pushing the lock button on the rke transmitter. The direction indicators flash three times and the led above the button ...

  • Page 20

    Remote keyless entry (rke) this system allows you to lock or unlock the doors and liftgate from distances up to approximately 66 ft (20 m) using a hand-held remote keyless entry (rke) transmit- ter. The rke transmitter does not need to be pointed at the vehicle to activate the system. Note: the line...

  • Page 21

    To unlock the doors and liftgate push and release the unlock button on the rke transmitter once to unlock the driver’s door or twice, within five seconds, to unlock all doors and the liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also ...

  • Page 22

    Replacing the battery in the key with remote control to replace the battery, proceed as follows: • push button a to open the metal insert b; • turn the screw c to unlock using a small screwdriver; • take out the battery case d and replace the battery e making sure that polarities are correct; • refi...

  • Page 23

    General information this device complies with part 15 of the fcc rules and rss-210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 24

    Once the doors have been locked with the rke transmit- ter, it will no longer be possible to unlock them by pressing central lock/unlock button. Note: with central locking active (led on), opening one of the front doors, it is possible to perform a central unlocking (led off). With central locking a...

  • Page 25

    Warning! • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • for personal security and safety in the event of a collision, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • before ex...

  • Page 26

    Doors lock with one or more doors open it is possible locking the vehicle through the rke, internal button or external key pawl, also if one or more doors are open. At lock command request, led is switched on. At closing of the last door, the vehicle maintains the central locking status if key is no...

  • Page 27

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged (locked). Note: for emergency exit from the rear seats when the child-protection door lock system is engaged, unlock the doors usin...

  • Page 28

    Note: the power window switches will remain active for up to three minutes after the ignition switch is cycled to the off position. Opening either front door will cancel this feature. Warning! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave...

  • Page 29

    Auto-down the window switches have an auto-down feature. Push the window switch for approximately one second, re- lease, and the window will go down automatically. To cancel the auto-down movement, operate the switch in either the up or down direction and release the switch. Auto-up feature with ant...

  • Page 30

    Resetting the auto up feature should the “auto up” feature stop working, the window probably needs to be reset. To reset “auto up”: 1. Pull the window switch up to close the window completely and continue to hold the switch up for an additional two seconds after the window is closed. 2. Push the win...

  • Page 31

    Warning! • driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • if you are required to drive with the liftgate open, make sure that all windows are c...

  • Page 32

    3. With the screwdriver remove the tab of yellow color (a) 4. Introduce the screwdriver into the seat b in order to trigger the release tab of the trunk (follow the direction arrow to open) yellow tab location release tab 30 things to know before starting your vehicle.

  • Page 33

    Occupant restraint systems some of the most important safety features in your vehicle are the restraint systems: • seat belt systems • supplemental restraint systems (srs) air bags • child restraints important safety precautions please pay close attention to the information in this section. It tells...

  • Page 34

    6. All occupants should always wear their lap and shoulder belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the advanced front air bags room to inflate. 8. Do not lean against the door or window. If your vehicle has side air bags, and deployme...

  • Page 35

    Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle....

  • Page 36

    Beltalert warning sequence the beltalert warning sequence is activated when the vehicle is moving above a specified vehicle speed range and the driver or outboard front seat passenger is un- buckled (the outboard front passenger seat beltalert is not active when the outboard front passenger seat is ...

  • Page 37

    Note: if beltalert has been deactivated and the driver or outboard front seat passenger is unbelted the seat belt reminder light will turn on and remain on until the driver and outboard front seat passenger seat belts are buckled. Lap/shoulder belts all seating positions in your vehicle are equipped...

  • Page 38

    Warning! (continued) • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure everyone in your vehicle is in a seat and using a seat belt properly. • wearing your seat belt incorrectly could make your injuries in a collision much worse. You ...

  • Page 39

    Warning! (continued) • a seat belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • a seat belt that is worn under your arm is dangerous. Your body could strike the inside surfaces o...

  • Page 40

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the sea...

  • Page 41

    4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding...

  • Page 42

    Position. If necessary, slide the latch plate down the webbing to allow the seat belt to retract fully. Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 1...

  • Page 43

    Position the lap belt snug and low below the abdomen and across the strong bones of the hips. Place the shoulder belt across the chest and away from the neck. Never place the shoulder belt behind the back or under the arm. Seat belt pretensioner the front seat belt system is equipped with pretension...

  • Page 44

    Switchable automatic locking retractor (alr) — if equipped the seat belts in the passenger seating positions are equipped with a switchable automatic locking retractor (alr) which is used to secure a child restraint system. For additional information, refer to “installing child restraints using the ...

  • Page 45

    Around the occupant’s mid-section so as to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occ...

  • Page 46

    How to engage the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire seat belt is extracted. 3. Allow the seat belt to retract. As the seat belt retracts, you will hear a clicking sound. This indicates the seat bel...

  • Page 47

    Supplemental restraint system (srs) air bag system components your vehicle may be equipped with the following air bag system components: • occupant restraint controller (orc) • air bag warning light • steering wheel and column • instrument panel • knee impact bolsters • advanced front air bags • sup...

  • Page 48

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 49

    Advanced front air bag features the advanced front air bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the occupant restraint controller (orc), which may receive information from the front i...

  • Page 50

    Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Seat belts are necessary for your protection in all colli- sions, and also are needed to help keep you in position, away f...

  • Page 51

    Supplemental driver knee air bag this vehicle is equipped with a supplemental driver knee air bag mounted in the instrument panel below the steering column. The supplemental driver knee air bag provides enhanced protection during a frontal impact by working together with the seat belts, pretensioner...

  • Page 52

    When the sab deploys, it opens the seam on the outboard side of the seatback’s trim cover. The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure occupants if they are not se...

  • Page 53

    Sabics may help reduce the risk of head or other injuries to front and rear seat outboard occupants in certain side impacts and/or vehicle rollover events, in addition to the injury reduction potential provided by the seat belts and body structure. The sabics deploy downward, covering the side win- ...

  • Page 54

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts and certain rollover events. The occupant restraint controller (“orc”) de- termines whether the deployment of the side air bags in a particular side impact or rollover event is appropriate, based on the severity a...

  • Page 55

    Warning! (continued) • relying on the side air bags alone could lead to more severe injuries in a collision. The side air bags work with your seat belt to restrain you properly. In some collisions, side air bags won’t deploy at all. Always wear your seat belt even though you have side air bags. Note...

  • Page 56

    The side air bags will not deploy in all rollover events. The rollover sensing system determines if a rollover event may be in progress and whether deployment is appropriate. In the event the vehicle experiences a roll- over or near rollover event, and deployment of the side air bags is appropriate,...

  • Page 57

    Irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s in- structions for cleaning. Do not drive your vehicle after the air bags have de-...

  • Page 58

    • turn on the interior lights, which remain on as long as the battery has power or for 15 minutes from the intervention of the enhanced accident response sys- tem. • unlock the power door locks. Enhanced accident response system reset procedure after the event occurs, when the system is active, a me...

  • Page 59

    Customer action customer will see 4. Turn left turn signal switch on. Left turn light is on solid. Right turn signal light blinks. 5. Turn right turn signal switch on. Right turn light is on solid. Left turn light blinks. 6. Turn left turn signal switch on. Left turn light is on solid. Right turn li...

  • Page 60

    Air bag warning light the air bags must be ready to inflate for your protection in a collision. The occupant re- straint controller (orc) monitors the internal circuits and interconnecting wiring associated with air bag system electrical components. The orc monitors the readiness of the electronic p...

  • Page 61

    • the air bag warning light remains on after the four to eight-second interval. • the air bag warning light comes on intermittently or remains on while driving. Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be dis...

  • Page 62

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 63

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Ch...

  • Page 64

    Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–732–8243. • canadian residents should refer to transport cana- da’s website for additional information: http:// www.Tc.Gc.Ca/eng/motorvehiclesafety/safedrivers- childsafety-index-53.Htm summary of recommendations for restra...

  • Page 65

    Child size, height, weight or age recommended type of child restraint larger children children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt belt positioning booster seat and the ve- hicle seat belt, seated in the rear seat of the ...

  • Page 66

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 67

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • after a child restraint i...

  • Page 68

    4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? 5. Can the child stay seated like this for the whole trip? If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the child is using t...

  • Page 69

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 70

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 71

    Latch positions for installing child restraints in this vehicle • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 2 things to know before starting your vehicle 69.

  • Page 72

    What is the weight limit (child’s weight + weight of the child restraint) for using the latch anchorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and teth...

  • Page 73

    Can two child restraints be attached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child s...

  • Page 74

    Locating latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the ...

  • Page 75

    Locating the upper tether anchorages there are tether strap anchorages behind each rear seating position located on the back of the seat, near the floor. Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to...

  • Page 76

    Tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center seat latch: warning! • do not install a child restraint in the center posi- tion using the latch system. This position is not ...

  • Page 77

    2. Place the child seat between the lower anchorages for that seating position. For some second row seats, you may need to recline the seat and / or raise the head restraint to get a better fit. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move it to its rear-mo...

  • Page 78

    Behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. Do not lock the seat belt. Remind all children in the vehicle that the seat belts are not toys and that they should not play with them. Warning! • improper installation of a child restraint to t...

  • Page 79

    Lap/shoulder belt systems for installing child restraints in this vehicle • alr = switchable automatic locking retractor 2 things to know before starting your vehicle 77.

  • Page 80

    What is the weight limit (child’s weight + weight of the child restraint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a forward facing child restraint, ...

  • Page 81

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 82

    Strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direc...

  • Page 83

    1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another p...

  • Page 84

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 85

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tip...

  • Page 86

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 87

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 88

    Floor mat safety information always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in o...

  • Page 89

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 91: Contents

    Understanding the features of your vehicle contents ! Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 ▫ inside day/night mirror . . . . . . . . . . . . . . . .92 ▫ automatic dimming mirror — if equipped . . .93 ▫ conversation mirror — if equipped . . . . . . . . .94 ▫ power mirro...

  • Page 92

    ▫ turn signals . . . . . . . . . . . . . . . . . . . . . . . . .115 ▫ lane change assist . . . . . . . . . . . . . . . . . . . .115 ▫ follow me home/headlight delay . . . . . . . . .115 ▫ front fog lights — if equipped . . . . . . . . . . .116 ▫ interior lights . . . . . . . . . . . . . . . . . . . ...

  • Page 93

    ▫ programming a rolling code . . . . . . . . . . . . .139 ▫ programming a non-rolling code . . . . . . . . .142 ▫ canadian/gate operator programming . . . . . .143 ▫ using homelink®. . . . . . . . . . . . . . . . . . . . .145 ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 ▫ tr...

  • Page 94

    Mirrors inside day/night mirror a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjus...

  • Page 95

    Automatic dimming mirror — if equipped this mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activat...

  • Page 96

    Conversation mirror — if equipped there is a conversation mirror located at the top of the overhead console. To gain access to the conversation mirror, pull downward on the mirror to the open position. Conversation mirror location conversation mirror 94 understanding the features of your vehicle.

  • Page 97

    Power mirrors the power mirror controls are located on the driver’s door trim panel. To adjust a mirror, turn the control knob toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the...

  • Page 98

    Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster. Sun visors the driver and passenger sun visors are located on the headliner, near the front windshield. The sun visor can be rotated downward or u...

  • Page 99

    To use the “slide-on-rod” feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “slide-on-rod” until the sun visor is in the desired position. Seats front seats forward/rearward adjustment the adjusting bar is located at the front of the seats, near the floor. While sitt...

  • Page 100

    Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could...

  • Page 101

    Seat height adjustment the seat height adjustment lever is located on the out- board side of the seat. Pull upward on the lever to raise the seat height or push downward on the lever to lower the seat height. Recliner adjustment the recline lever is located on the outboard side of the seat. To recli...

  • Page 102

    Warning! • adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust the seat only while the vehicle is parked. • do not ride with the seatback reclined so ...

  • Page 103

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the outer side of the seat. Note: once a heat setting is selected, heat will be felt within two...

  • Page 104

    Rear seats rear seats forward/rearward adjustment the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once the desired position is reached. Then, using body pressure, move forward...

  • Page 105

    Reclining rear seats the recliner handle is located on the outside of the seat cushion. To adjust the seatback, lift upward on the handle, lean back on the seatback and when you reach the desired position, release the handle. Warning! Do not ride with the seatback reclined so that the shoulder belt ...

  • Page 106

    1. Lift the seatback release lever located on the upper outboard side of the seat. 2. Fold the seatback forward. 3. Locate the seatback recline lever on the outboard side of the seat and lift upward on the lever. Seatback release lever seatback folded 104 understanding the features of your vehicle.

  • Page 107

    4. Slowly flip the entire seat forward. 5. Slowly flip the entire seat rearward and firmly lock the seat into position. 6. Raise the rear seatback and firmly lock the seatback into position. Seatback recline lever folding rear seat 3 understanding the features of your vehicle 105.

  • Page 108

    Rear armrest — if equipped to use the armrest, lower it downward. Head restraints head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear- impact. Head restraints should be adjusted so that the top of the head restraint is located above the top o...

  • Page 109

    Warning! The head restraints for all occupants must be prop- erly adjusted prior to operating the vehicle or occu- pying a seat. Head restraints should never be ad- justed while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious in...

  • Page 110

    The reactive head restraints will automatically return to their normal position following a rear impact. If the reactive head restraints do not return to their normal position, see your authorized dealership immediately. Warning! • a loose head restraint thrown forward in a colli- sion or hard stop ...

  • Page 111

    Rear head restraints the rear seats are equipped with adjustable head re- straints, the outboard head restraints have two comfort positions, while the central head restraint have to use in the raised position. When there are no occupants in the center seat, the head restraint can be lowered for maxi...

  • Page 112

    For proper routing of a child seat tether, refer to “occupant restraints” in “things to know before start- ing your vehicle.” warning! All the head restraints must be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the ve...

  • Page 113

    1. Pull the hood release lever located under the left side of the instrument panel. 2. Move to the outside of the vehicle and push the red safety catch lever to the left and raise the hood. The safety catch lever is located under the center front edge of the hood. Hood release lever safety catch lev...

  • Page 114

    Caution! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 6 inches (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. Warning! Be sure the hood i...

  • Page 115

    Headlights rotate the end of the multifunction lever up- ward to the first detent for headlight operation. Note: when the headlights are turned on, the daytime running lights will be deactivated. Multifunction lever headlight operation 3 understanding the features of your vehicle 113.

  • Page 116

    Daytime running lights — if equipped to activate the daytime running lights (drl), rotate the end of the multifunction lever to the o symbol. Note: the low beams and side/tail lights will not be on with drl. The drl function can be turned on or off through the touchscreen. Refer to your uconnect® su...

  • Page 117

    Turn signals move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside l...

  • Page 118

    Front fog lights — if equipped the fog light switch is located on the center stack of the instrument panel, just below the radio. Push the switch once to turn the front fog lights on. Push the switch a second time to turn the front fog lights off. Interior lights the interior light switches are loca...

  • Page 119

    Push the switch to the off/left position from its center position and the lights are always off. Leave the switch in the center position, and the lights are turned on and off when the doors are opened or closed. Off/left position center position 3 understanding the features of your vehicle 117.

  • Page 120

    The switches on the left and right sides of the overhead console controls the map or reading function of the lights. Push the switch to the right to turn on the right light and push the switch to the left to turn on the left light. Caution! Before getting out of the vehicle be sure that the switch i...

  • Page 121

    • when the doors are unlocked with the key fob a 10 second timer is activated. • when the doors are locked with the key fob the lights will turn off. Interior light timing (on/right position) • when all doors are closed a 15 minute timer is activated. Note: the timer is deactivated when the key is m...

  • Page 122

    Windshield wiper off this is the normal position of the wiper lever. Intermittent speed rotate the end of the lever upward to the first detent. The wipers will operate at intermittent speed. Low speed rotate the end of the lever upward to the second detent. The wipers will operate at low speed. High...

  • Page 123

    Caution! • turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • in cold weather, always turn off the wiper switch and allow the wipers to return to the “park” posi- tion be...

  • Page 124

    Rear window wiper/washer activation rotate the windshield wiper lever center ring upwards to operate the rear window wiper as follows: • in intermittent mode when the front windshield wiper is not operating. • in synchronous mode (at half the speed of the front window wiper) when the front windshiel...

  • Page 125

    Deactivation the function stops when the windshield wiper lever is released. Tilt/telescoping steering column this feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located on the s...

  • Page 126

    To unlock the steering column, pull the control handle down. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the...

  • Page 127

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by pushing the electronic speed control on/off but...

  • Page 128

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 129

    To vary the speed setting to increase speed when the electronic speed control is set, you can in- crease speed by pushing the res (+) button. The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “under- standing your instrument panel” for more infor...

  • Page 130

    The speed decrement shown is dependant on the selected speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pushing the set (-) button once will result in a 1 mph decrease in set speed. Each subsequent tap of the button results in a decrease of 1 mph. • if the button is continually pushed, ...

  • Page 131

    Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control and have an accident. Do not use electronic speed control in heavy traffic or on roads that are winding, icy, snow-cov...

  • Page 132

    Rear park assist sensors the four rear park assist sensors, located in the rear fascia/bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles, in the horizontal direction, from approximately 12 in (30 cm) up to 55 in (140 cm) from the ...

  • Page 133

    Audible and visual signals supplied by the rear park assist system signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loudspeaker) • sound pulses emitted at a rate that increases as the distance decreases. • emits continuous...

  • Page 134

    While audible signals are emitted, the audio system is not muted. The audible signal is turned off immediately if the distance increases. The tone cycle remains constant if the distance measured by the inner sensors is constant. If this condition occurs for the external sensors, the signal is turned...

  • Page 135

    Cleaning the rear park assist system clean the rear park assist sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. In washing stations, clean sensors quickly keeping the va- por jet/high pressure washing nozzles at least 4 in (10 cm) from the sensors. Do not scratch...

  • Page 136

    Caution! • rear park assist is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily de- tected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • the v...

  • Page 137

    Warning! (continued) could detect the ball mount and hitch ball assem- bly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle. If it’s necessary to keep the ball mount and hitch ball assembly mounted for a long period, it is possible to filter out the ...

  • Page 138

    When enabled, fixed guide lines are overlaid on the image to illustrate the width of the vehicle. Note: the parkview® rear back up camera has pro- grammable modes of operation that may be selected through the uconnect® system. Refer to your uconnect® supplement manual for further information. Differ...

  • Page 139

    Warning! Drivers must be careful when backing up even when using the parkview® rear back up camera. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, ob- structions, or blind spots before backing up. You are responsible for the safety of your ...

  • Page 140

    Garage door opener — if equipped homelink® replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security systems. The homelink® unit operates off your vehicles battery. The homelink® buttons that are locate...

  • Page 141

    Before you begin programming homelink® be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the d...

  • Page 142

    1. Place the ignition in the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light in view. 3. Push and hold the homelink® button you want to program while you push and hold the han...

  • Page 143

    5. At the garage door opener motor (in the garage), locate the “learn” or “training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener/device motor. Firmly push and release the “learn” or “train- ing” button. On some garage door openers/devices th...

  • Page 144

    Programming a non-rolling code for programming garage door openers manufactured before 1995. 1. Place the ignition in the on/run position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program while keeping the homelink® indicator light in vi...

  • Page 145

    3. Without releasing the button proceed with “program- ming a non-rolling code” step 2 and follow all remaining steps. Canadian/gate operator programming for programming transmitters in canada/united states that require the transmitter signals to “time-out” after several seconds of transmission. Can...

  • Page 146

    5. Push and hold the programmed homelink® button and observe the indicator light. • if the indicator light stays on constantly, program- ming is complete and the garage door/device should activate when the homelink® button is pushed. • to program the two remaining homelink® buttons, repeat each step...

  • Page 147

    Using homelink® to operate, switch the ignition to the on/run position and the press and release the programmed homelink® button. Activation will now occur for the programmed device (i.E., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,). The hand-hel...

  • Page 148

    Warning! • vehicle exhaust contains carbon monoxide, a dan- gerous gas. Do not run your vehicle in the garage while programming the transceiver. Exhaust gas can cause serious injury or death. • your motorized door or gate will open and close while you are programming the universal trans- ceiver. Do ...

  • Page 149

    • the term ic before the certification/registration num- ber only signifies that industry canada technical speci- fications were met. Power sunroof — if equipped the sunroof has two glass panels (the front one is operational and the rear one fixed) and is equipped with an electrically operated sun b...

  • Page 150

    Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle or in a location accessible to children. Occupants, particularly unattended children, can become entrapped by the power sun- roof while operating the power sunroo...

  • Page 151

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 152

    Power outlets passenger compartment power socket the power outlet is located on the central tunnel, in front of the shift lever, between the two cup holders. It only operates with the ignition key at mar/on. On models with optional #smoker’s kit,# the cigar lighter takes the place of the power socke...

  • Page 153

    Cigar lighter — if equipped this is located on the central tunnel, next to the parking brake lever. To activate the cigar lighter, push and release the knob. After a few seconds the knob automatically returns to its initial position, and the cigar lighter is ready for use. Warning! When the cigar li...

  • Page 154

    Cupholders for the driver and front passenger, cupholders are lo- cated on the floor console between the front seats. For the rear seat passengers their is one cupholder located in the center armrest. Front cupholders rear cupholder 152 understanding the features of your vehicle.

  • Page 155

    Storage glove compartment your vehicle is equipped with a upper and lower glove compartment which is located on the right side of the instrument panel. Push the latch button upward on the upper glove compartment door to open it. Pull outward on the lower glove compartment latch to open the lower glo...

  • Page 156

    Front center armrest storage — if equipped the front center armrest contains a storage compartment. To open the storage compartment push in the upper release latch on the front of the armrest. Lift upward on the armrest to gain access to the storage area. Glove compartment storage armrest upper rele...

  • Page 157

    The front center armrest can also be lifted up and adjusted in three positions, this is done by pulling up on the armrest, push the latch down to adjust the armrest down. Rear cargo storage features the car features a load platform which can be adjusted to three different heights, permitting modular...

  • Page 158

    • position 3 (platform completely raised) in conjunction with the lowering of the rear seat and front passenger side seat backrests, permits long objects to be loaded. It is advisable to use this position only for the actual period in which the objects are transported, then return the platform to po...

  • Page 159

    Caution! The dimension of the cargo floor permit a maximum capacity of a distributed weight of 154 lbs (70kg) (if positioned at threshold level) or 88 lbs (40 kg) (if positioned at raised level) do not add objects with a higher weight. Access to double load compartment to access the double load comp...

  • Page 160

    3. Then reposition the platform correctly in the housings on the side panels and rear crossmember. Note: movements of the load platform must take place in a central position relative to the luggage compartment. Load compartment platform housings 1 — front locations 2 — rear locations 158 understandi...

  • Page 161

    Moving the load platform to move the load platform from lower to upper position, proceed as follows: 1. Grip handle and raise the platform, holding it with one hand. 2. Position the platform correctly on housing on the side panels. Load platform 1 — handle 2 — platform 3 understanding the features o...

  • Page 162

    Securing your load there are two tie downs inside the luggage compartment for attaching cables which can secure the load carried. A further two tie downs located on the rear crossmember. Raised position 1 — front housing locations 2 — rear housing locations cargo tie down locations 160 understanding...

  • Page 163

    Two hooks are also available on the side panels to fix loads which are not excessively heavy (e.G. Bags). To use the hooks, push the release button. Caution! The maximum load admitted per each bag hook is 22 lbs (10 kg). Cargo side panel hook locations 1 — release button 2 — hook 3 understanding the...

  • Page 164

    Storage compartments there are two storage compartments located on the rear side panels. Rear window features rear window defroster the rear window defroster button is located with the climate controls on the instrument panel. Push this button to turn on the rear window defroster. An indicator in th...

  • Page 165

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 166

    Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity. Warning! Cargo must be secu...

  • Page 167: Contents

    Understanding your instrument panel contents ! Instrument panel features . . . . . . . . . .167 ! Instrument cluster . . . . . . . . . . . . . . . . .168 ! Instrument cluster descriptions . . . . .169 ! Electronic vehicle information center (evic) . . . . . . . . . . . . . . . . . . . . . . .180 ▫ e...

  • Page 168

    ▫ player operation . . . . . . . . . . . . . . . . . . . . . .193 ! Cd/dvd disc maintenance . . . . . . . . . . .193 ! Radio operation and mobile phones . .194 ! Climate controls . . . . . . . . . . . . . . . . . . .194 ▫ manual climate control system . . . . . . . . . . .194 ▫ automatic dual zone c...

  • Page 169

    Instrument panel features 1 — side vent 7 — fixed upper air vent 13 — climate controls 2 — steering wheel audio control — located on back side of steering wheel 8 — passenger advanced front air bag 14 — usb port/sd card/aux socket 3 — multifunction lever – light control 9 — upper glove compartment 1...

  • Page 170

    Instrument cluster 168 understanding your instrument panel.

  • Page 171

    Instrument cluster descriptions 1. Speedometer the speedometer shows the vehicle speed in miles per hour (mph) and/or kilometers per hour (km/h). 2. Cruise set indicator — if equipped this light will turn on when the electronic speed control is set. For further information, refer to “electronic spee...

  • Page 172

    Note: • the esc off indicator light and the esc activation/ malfunction indicator light come on momentarily each time the ignition switch is turned to on/run. • each time the ignition is turned to on/run, the esc system will be on, even if it was turned off previously. 5. Brake warning light this li...

  • Page 173

    Off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that ...

  • Page 174

    The gauge pointer will likely indicate a higher tempera- ture when driving in hot weather, or up mountain grades. It should not be allowed to exceed the upper limits of the normal operating range. Caution! Driving with a hot engine cooling system could damage your vehicle. If all the segments of the...

  • Page 175

    If the light turns on while driving, safely pull over and stop the vehicle. If the a/c system is on, turn it off. Also, shift the transmission into neutral and idle the ve- hicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “if...

  • Page 176

    16. Air bag warning light this light will turn on for four seconds as a bulb check when the ignition switch is first turned to on/run. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. Refer to “...

  • Page 177

    Certain conditions, such as poor fuel quality, etc., may illuminate the mil after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing. Caution! Prolonged dri...

  • Page 178

    As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illumi- nates, you should stop and c...

  • Page 179

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...

  • Page 180

    22. Odometer / trip odometer / electronic vehicle infor- mation center (evic) display area this display indicates the total distance the vehicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the...

  • Page 181

    Shift lever is placed in the neutral position. The light should turn off. If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible. If the light is flashing when the engine is running, imme- diate servi...

  • Page 182

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic consists of the following: • system status • vehicle information warning message displays • personal settings (cus...

  • Page 183

    Evic control buttons the evic control buttons are located on the instrument panel below the radio. Push and release the menu button briefly to access the menu and/or go to next screen or to confirm the required menu option. Push and hold the menu button (approxi- mately one second) to return to the ...

  • Page 184

    Electronic vehicle information center (evic) setup menu the menu comprises a series of functions arranged in a cycle. The menu includes the following functions: • dimmer • speed buzzer • first page • buzzer volume • belt buzzer • hill start • exit menu • selecting an option of the main menu without ...

  • Page 185

    Briefly push and release the menu button to select the displayed submenu option and to open the relevant setup menu. Push and release the up or down button (by single pushes) to select the new setting for this sub- menu option. Briefly push and release the menu button to store the new setting and go...

  • Page 186

    Note: if the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. Trip computer the trip computer is located in the instrument cluster. It features a driver-interactive display (displays informa- tion such as; t...

  • Page 187

    New trip to reset: • push and hold the trip button to reset the system manually. • when the “trip distance” reaches 9999.9 miles or kilometers or when the “travel time” reaches 999.59 (99 hours and 59 minutes), the system is reset auto- matically. • disconnecting/reconnecting the battery resets the ...

  • Page 188

    Trip functions both trip functions are resettable (reset — start of new trip). “trip a” can be used to display the figures relating to: • range • trip distance a • average economy a • instant economy • average speed a • travel time a (driving time). “trip b” can be used to display the figures relati...

  • Page 189

    Note: the range depends on several factors: driving style, type of route (freeway, residential, mountain roads, etc.), conditions of use of the car (load, tire pressure, etc.). Trip planning must take into account the above notes. Distance traveled this value shows the distance covered since the las...

  • Page 190

    • push and release the set esc button briefly to return to the submenu screen or hold the button down to return to the main menu screen without saving. Buzzer volume (adjusting the failure/warning buzzer volume) with this function the volume of the buzzer accompany- ing any failure/warning indicatio...

  • Page 191

    3. When the function is activated (on), briefly push and release the menu button to display the presently set activation speed. Pushing the up or down buttons selects the speed limit. Push menu to confirm selection. Note: selection is possible between 20 – 125 mph or (32 – 201 km/h), depending on th...

  • Page 192

    To adjust the brightness, proceed as follows: 1. Push and release the up or down button to set the required brightness level. 2. Briefly push and release the menu button to go back to the menu screen or push and hold the menu (approximately one second) to go back to the main screen without storing s...

  • Page 193

    Exit menu this function closes the initial menu screen. Briefly push and release the menu button to go back to the main screen. Push and release the button to return to the first menu option (speed beep). Push and release the button to return to the last menu option (daylights). Uconnect® radios for...

  • Page 194

    Steering wheel audio controls the remote sound system controls are located at the rear of the steering wheel. Reach behind the wheel to access the switches. The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pushing th...

  • Page 195

    Radio operation pushing the top of the switch will “seek” up for the next listenable station and pushing the bottom of the switch will “seek” down for the next listenable station. The button located in the center of the left-hand control will tune to the next preset station that you have pro- gramme...

  • Page 196

    Note: if you experience difficulty in playing a particular disc, it may be damaged (i.E., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. Radio operation and mobile phone...

  • Page 197

    The manual climate controls consist of a series of rotary dials, an inner push knob and two push buttons. 1. Temperature control rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial to the left into the blue area of the scale indicates cooler...

  • Page 198

    3. Blower control rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “0” (off) position. There are four blower speeds. 4. A/c button push this button to engage the air condition...

  • Page 199

    • bi-level air is directed through the panel and floor outlets. • floor air is directed through the floor outlets with a small amount flowing through the defrost and side window demister outlets. • mix air is directed through the floor, defrost, and side window demister outlets. This setting works b...

  • Page 200

    Air recirculation push and release the air recirculation button, so that the led on the button switch is on, to enter recirculation mode. It is advisable to switch internal air recirculation on while standing in traffic or in tunnels to prevent the introduction of polluted air. Do not use the functi...

  • Page 201

    Selecting the footwell/windshield or only windshield distribution activates the climate control system com- pressor (led on a/c button on) and the air recirculation is set to #outside air# (led on recirculation control button off ). This logic guarantees optimum visibility at the windows. The user c...

  • Page 202

    Automatic dual zone climate control system (if equipped) controls 1. Driver temperature control provides the driver with independent temperature con- trol. Rotate adjustment knob to set desired temperature. Note: in sync mode, this button will also automatically adjust the passenger temperature sett...

  • Page 203

    3. Rear defrost control push and release the rear defrost control button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 20 minutes. 4. A/c co...

  • Page 204

    9. Front defrost control push and release the front defrost control button to change the current airflow setting to defrost mode. The indicator illuminates when this feature is on. Perform- ing this function will cause the atc to switch into manual mode. The blower speed may increase when defrost mo...

  • Page 205

    The system maintains comfort inside the passenger com- partment and compensates for possible variations in external climate conditions. The climate control system can recognize extremely cold (or extremely hot) conditions in the passenger compart- ment and consequently provide optimal management of ...

  • Page 206

    The system allows the following to be set or adjusted manually: • driver/passenger side air temperature • fan speed (continuous variation) • air distribution to seven positions • compressor enablement • rapid defrosting/demisting function • air recirculation • heated rear window • system deactivatio...

  • Page 207

    During automatic operation, you can change the set temperatures, air distribution and fan speed at any time by using the relevant buttons or knobs: the system will automatically change the settings to adjust to the new requirements. During completely automatic operation (auto), varying the air flow ...

  • Page 208

    To deactivate these functions, turn the temperature knob to the desired temperature. Air distribution selection by pushing the mode control buttons (up/down/right arrows), it is possible to set one of the seven possible air distributions manually: • up arrow – air flow to the windshield and front si...

  • Page 209

    • up/right/down arrows – air flow distribution to all diffusers on the car. Note: air always flows from the side dashboard diffus- ers: it is, however, possible to interrupt the air flow by operating the wheel located near the corresponding vents. In auto mode, the climate control system automatical...

  • Page 210

    If the auto button is pushed when the auto led is on, the system switches to completely manual mode; it displays the current flow and distribution status, which will no longer be managed automatically. If a manual intervention is made on at least the air distribution, on compressor button or on the ...

  • Page 211

    Air recirculation the air recirculation is managed according to the fol- lowing operating logics: • forced activation (air recirculation always on): indi- cated by the led on the recirculation control button • forced deactivation (air recirculation always off, air intake from the outside), signalled...

  • Page 212

    Climate control system compressor push the a/c control button to activate/deactivate the compressor (activation is indicated by the led on the button switching on). The system remembers that the compressor has been switched off, even after the engine has stopped. When the compressor is switched off,...

  • Page 213

    Note: the front defrost control (max-def) function remains on for about three minutes from when the engine coolant reaches the appropriate temperature. When the function is activated, the led on the auto button switches off. With the function activated the only possible manual adjustments are adjust...

  • Page 214

    Switching off the climate control system push the on/off button. With climate control system off: • air recirculation is on, thus isolating the passenger compartment from the outside; • the compressor is off; • the fan is off; • the heated rear window can be activated / deacti- vated. Note: the clim...

  • Page 215

    Uconnect® voice recognition quick tips introducing uconnect® start using uconnect® voice recognition with these helpful quick tips. It provides the key voice commands and tips you need to know to control your uconnect® 5.0 or 6.5a/6.5an system. Key features: • 5.0-inch color touchscreen display with...

  • Page 216

    Key features: • 6.5-inch color touchscreen display with am/fm/ usb/sd card/bluetooth® • bluetooth with integrated voice control • gps navigation (if equipped) get started all you need to control your uconnect® system with your voice are the buttons on your steering wheel. 1. Visit uconnectphone.Com ...

  • Page 217

    Basic voice commands the basic voice commands below can be given at any point while using your uconnect® system. Push the vr button . After the beep, say$ • cancel to stop a current voice session. • help to hear a list of suggested voice commands. • repeat to listen to the system prompts again. Ucon...

  • Page 218

    Notice the visual cues that inform you of your voice recognition system’s status. Cues appear on the touch- screen. Uconnect® 5.0 uconnect® 6.5a/6.5an 216 understanding your instrument panel.

  • Page 219

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio® stations you would like to hear. (sub- scription or included siriusxm satellite radio® trial required.) push the vr button . After the beep, say$ • tune to ninety-five-point-five fm. • tune to satellite channel hits 1. Ti...

  • Page 220

    Media uconnect® offers connections via usb port, bluetooth® and auxiliary ports (if equipped). Voice operation is only available for connected usb and ipod® devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands ...

  • Page 221

    Tip: press the browse button on the touchscreen to see all of the music on your ipod® or usb device. Your voice command must match exactly how the artist, album, song and genre information is displayed. Uconnect® 5.0 media uconnect® 6.5a/6.5an media 4 understanding your instrument panel 219.

  • Page 222

    Phone making and answering hands-free phone calls is easy with uconnect®. When the phonebook button is illumi- nated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Push the phone button . After the beep, say one of the foll...

  • Page 223

    Navigation (6.5a/6.5an) the uconnect® navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. 1. To enter a destination, push the vr button . After the beep, say: • for the 6.5an uconnect® system, say: “navigate to 800 chrysler driv...

  • Page 224

    Tip: to start a poi search, push the vr button . After the beep, say: “ find nearest coffee shop.” voice text reply uconnect® will announce incoming text messages. Push the phone button and say “listen.” (must have compatible mobile phone paired to uconnect® sys- tem.) 1. Once an incoming text messa...

  • Page 225

    Pre-defined voice text reply responses yes. Stuck in traffic. See you later. No. Start without me. I’ll be late. Okay. Where are you? I will be minutes late. Call me. Are you there yet? I’ll call you later. I need directions. See you in of minutes. I’m on my way. Can’t talk right now. I’m lost. Than...

  • Page 227: Starting And Operating

    Starting and operating contents ! Starting procedures . . . . . . . . . . . . . . . .229 ▫ manual transmission — if equipped . . . . . . .229 ▫ automatic transmission — if equipped . . . . .229 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .230 ▫ cold weather operation . . . . . . . ....

  • Page 228

    ! Driving on slippery surfaces . . . . . . . . .255 ▫ acceleration . . . . . . . . . . . . . . . . . . . . . . . . .255 ▫ traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 ! Driving through water . . . . . . . . . . . . .256 ▫ flowing/rising water . . . . . . . . . . . . . . . . . ...

  • Page 229

    ▫ tire inflation pressures . . . . . . . . . . . . . . . . .283 ▫ tire pressures for high speed operation . . . .284 ▫ radial ply tires . . . . . . . . . . . . . . . . . . . . . .284 ▫ tire types . . . . . . . . . . . . . . . . . . . . . . . . . . .285 ▫ run flat tires — if equipped . . . . . . . . ...

  • Page 230

    ! Adding fuel . . . . . . . . . . . . . . . . . . . . . . . .306 ! Trailer towing . . . . . . . . . . . . . . . . . . . . .308 ! Recreational towing (behind motorhome, etc.) . . . . . . . . . . . . . . . . . . .309 ▫ towing this vehicle behind another vehicle . .309 228 starting and operating.

  • Page 231

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 232

    Normal starting note: normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. Turn the ignition switch to the avv/acc (start) position and release it when the engine starts. If the engine fails to start within 10 seconds, turn the ignition swi...

  • Page 233

    3. If the engine fails to start within ten seconds, cycle the ignition to the stop (off/lock) position, wait five seconds to allow the starter to cool, then repeat the extended park starting procedure. 4. If the engine fails to start after eight attempts, allow the starter to cool for at least 10 mi...

  • Page 234

    After starting the idle speed is controlled automatically and it will decrease as the engine warms up. Turbo charger “cool down” this vehicle is equipped with an after-run pump to cool the turbocharger after the engine is shut off. Depending on the type of driving and the amount of cargo, the pump w...

  • Page 235

    Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position. Damage to the clutch can result from starting in third. For most city driving you will find it easier to use only the lower gears. For steady highway ...

  • Page 236

    Downshifting proper downshifting will improve fuel economy and prolong engine life. Caution! If you skip a gear while downshifting or downshift at too high of a vehicle speed, these conditions may cause the engine to overspeed if too low of a gear is selected and the clutch pedal is released. Damage...

  • Page 237

    Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only shift ...

  • Page 238

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock/ off (key removal) position. The key can only be re- moved from the ignition when the ignition is in the lock/o...

  • Page 239

    This transmission is programmed to prevent shifting from reverse to drive or drive to reverse, if vehicle speed is above 6 mph (10 km/h). This safety feature helps protect your transmission from damage. Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle i...

  • Page 240

    Note: if the shift lever cannot be moved to the park, reverse, or neutral position (when pushed for- ward) it is probably in the autostick (+/-) position (beside the drive position). In autostick mode, the transmission gear (1, 2, 3, etc.) is displayed in the instrument cluster. Move the shift lever...

  • Page 241

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to mo...

  • Page 242

    Warning! (continued) • do not leave the ignition key in or near the vehicle (or in a location accessible to children). A child could operate power windows, other controls, or move the vehicle. Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off p...

  • Page 243

    Neutral (n) use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the parking brake and shift the transmission into park if you must leave the vehicle. Warning! Do not coast in neutral and never turn off the ignition...

  • Page 244

    To maximize fuel economy, the euro twin clutch six speed transmission uses a geartrain arrangement similar to a manual transmission. Therefore, you should become familiar with some of the normal operational character- istics of this transmission: • during low-speed driving conditions in first gear, ...

  • Page 245

    • during extremely cold temperatures, the transmission will not operate if the oil temperature is -22° f (-30° c) or below. Allow the engine to idle briefly with the transmission in park in order to warm the fluid. Normal operation will resume once the transmission temperature has risen to a suitabl...

  • Page 246

    Message description automatic unavailable the transmission is unable to shift itself automatically, due to a fault condition. Use the autostick mode to shift the transmission manually. See your authorized dealer for diagnosis and service. Reduce gear changes the transmission pump is overheating. In ...

  • Page 247

    Message description service transmission a transmission fault has been detected. See your authorized dealer for diagnosis and service. Service a shift lever fault has been detected. See your authorized dealer for diag- nosis and service. Set park brake the sensor that confirms park engagement is not...

  • Page 248

    3. Turn the ignition switch to the off position. 4. Wait approximately 10 seconds. 5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. Note: even if the transmission can be reset, we recom- mend that you...

  • Page 249

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has park, reverse, neu- tral, drive, and autostick shift positions. Manual shifts c...

  • Page 250

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 251

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 252

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 253

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 254

    If the transmission temperature exceeds normal operating limits, the transmission controller will expand the range of torque converter clutch engagement. This is done to pre- vent transmission damage due to overheating. During cold temperatures, transmission operation may be modified depending on en...

  • Page 255

    Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required...

  • Page 256

    • the transmission will automatically downshift to first gear when coming to a stop. After a stop, the driver should manually upshift (+) the transmission as the vehicle is accelerated. • with six-speed automatic (aisin f21-250 hd) trans- mission, you can start out (from a stop) in first, second, or...

  • Page 257

    Driving on slippery surfaces acceleration rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the driving wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels. Warning! ...

  • Page 258

    Driving through water driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow...

  • Page 259

    Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • determine the condition of the road or the path that is under water and if there are any obstacles in the wa...

  • Page 260

    Parking brake before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave manual transmission in reverse or first gear. The parking brake lever is located in the center console. To apply the parking brake, pull the lever up as firmly as possible. To relea...

  • Page 261

    When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. Warning! • never leave children alone in a vehicle, or with access to ...

  • Page 262

    Brake system your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still func- tion. However, there will be some loss of overall braking effectiveness. You may notice increased pedal travel during applica...

  • Page 263

    The system’s pump motor runs during an abs stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation, which is normal. The abs includes an amber abs warning light. When the light is illuminated, the abs is not functioning. The system reverts to standard ...

  • Page 264

    Engagement of the abs may be accompanied by a pulsing sensation. You may also hear a clicking noise. These occurrences are normal and indicate that the system is functioning properly. Brake assist system (bas) the bas is designed to optimize the vehicle’s braking capability during emergency braking ...

  • Page 265

    Traction control system (tcs) the traction control system (tcs) monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide en- hanced acceleration and stability. A feature of the...

  • Page 266

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 5% grade or greater hill. • gear selection matches vehicle uphill direction (i.E., vehicle in neutral (manual transmission), vehicle facing uphill is in forward ...

  • Page 267

    The coordinated action of brakes and steering increases the safety and car control feeling. Note: the dst is a driving aid system and does not replace the driver’s actions while driving the car. Electronic stability control (esc) this system enhances directional control and stability of the vehicle ...

  • Page 268

    Warning! (continued) never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. Esc activation/malfunction indicator light and esc off indicator light the esc activation/malfunction indicator light in the instrument cluster will come on whe...

  • Page 269

    The esc off indicator light indicates the electronic stability control (esc) is partially off. Esc operating modes the esc system has two available operating modes. Full on this is the normal operating mode for esc. Whenever the vehicle is started the system will be in this mode. This mode should be...

  • Page 270

    Note: to improve the vehicle’s traction when driving with snow chains, or when starting off in deep snow, sand, or gravel, it may be desirable to switch to the “partial off” mode by momentarily pushing the “esc off” button. Once the situation requiring “partial off” mode is overcome, turn esc back o...

  • Page 271

    Warning! Many factors, such as vehicle loading, road condi- tions, and driving conditions, influence the chance that wheel lift or rollover may occur. Erm cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. The capabili...

  • Page 272

    Note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design standards. Tires designed to this standard ...

  • Page 273

    Tire sizing chart example: example size designation: p215/65r15xl 95h, 215/65r15 96h, lt235/85r16c, t145/80d18 103m, 31x10.5 r15 lt p = passenger car tire size based on u.S. Design standards, or % ....Blank....% = passenger car tire based on european design standards, or lt = light truck tire based ...

  • Page 274

    Example: 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operat...

  • Page 275

    Example: maximum load – maximum load indicates the maximum load this tire is designed to carry maximum pressure – maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire tire identification number (tin) the tin may be found on one or both sides of the tire, howe...

  • Page 276

    Example: dot ma l9 abcd 0301 03 = number representing the week in which the tire was manufactured (two digits) – 03 means the 3rd week 01 = number representing the year in which the tire was manufactured (two digits) – 01 means the year 2001 – prior to july 2000, tire manufacturers were only require...

  • Page 277

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 278

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) example tire placard location (b-pillar) 276 starting an...

  • Page 279

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 280

    Note: under a maximum loaded vehicle condition, gross axle weight ratings (gawrs) for the front and rear axles must not be exceeded. For further information on gawrs, vehicle loading, and trailer towing, refer to “vehicle loading” in this manual. To determine the maximum loading conditions of your v...

  • Page 281

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 282

    280 starting and operating.

  • Page 283

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 284

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 285

    Tire inflation pressures the proper cold tire inflation pressure is listed on the driver’s side b-pillar or rear edge of the driver’s side door. At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judgement when determining pro...

  • Page 286

    Inflation pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12°f (7°c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too ...

  • Page 287

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 288

    Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Warning! Do not use summer tires in snow/ice conditions. You could lose vehi...

  • Page 289

    Run flat tires — if equipped run flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation pressure. This rapid loss of inflation is referred to as the run flat mode. A run flat mode occurs when the tire inflation pressure is of/or below 14 psi...

  • Page 290

    Rotation for your vehicle. If your vehicle has this option, refer to an authorized tire dealer for the recommended tire rotation pattern. Compact spare tire — if equipped the compact spare is for temporary emergency use only. You can identify if your vehicle is equipped with a compact spare by looki...

  • Page 291

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the ...

  • Page 292

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 293

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. L...

  • Page 294

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance w...

  • Page 295

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 296

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage. • traction device must be of proper size for the tire, as recommended by the traction device manufacturer. • install on front tires only. • due to l...

  • Page 297

    Caution! (continued) • observe the traction device manufacturer’s instruc- tions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufac- turer’s if it is less than 30 mph (48 km/h). • do not use traction devices on a com...

  • Page 298

    The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern does not apply to some directional tires that must not be reversed. Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure b...

  • Page 299

    The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning limit for any reason, including low temperature effects, or natural pressure loss through the tire. The tpms will continue to warn the driver of low tire pressure as long as the condition e...

  • Page 300

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, ...

  • Page 301

    • driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and i...

  • Page 302

    Tire pressure monitoring low pressure warnings the tire pressure monitoring telltale light will illumi- nate in the instrument cluster, an audible chime will be activated, and the “check left or right front/rear tire” text message will display when one or more of the four active road tire pressures ...

  • Page 303

    Note: your vehicle may be equipped with a compact spare wheel and tire assembly. • the compact spare tire does not have a tire pressure monitoring sensor. Therefore, the tpms will not moni- tor the tire pressure in the compact spare tire. • if you install the compact spare tire in place of a road ti...

  • Page 304

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 305

    Reformulated gasoline many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline”. Reformulated gasoline contain oxygenates and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The use of reformulated gasoline is recom...

  • Page 306

    Mmt in gasoline methylcyclopentadienyl manganese tricarbonyl (mmt) is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with mmt provides no performance advantage beyond gasoline of the same octane number without mmt. Gasoline blended wi...

  • Page 307

    Caution! (continued) • an out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to over- heat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized...

  • Page 308

    Warning! (continued) • guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Adding fuel 1. Open the fuel filler door. 2. The...

  • Page 309

    Funnel location inside of tool kit funnel location for vehicle with optional spare tire 5 starting and operating 307.

  • Page 310

    Caution! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. Warning! • never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled. • never add fuel when the engine is running. This is in violation of most stat...

  • Page 311

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground manual transmission euro twin clutch transmission automatic transmission (aisin f21-250 hd transmission ) flat tow none transmission in neutral transmission in neutral not a...

  • Page 312

    Vehicles equipped with a manual transmission, or a euro twin clutch transmission, may be flat towed (with all four wheels on the ground) at any legal highway speed, for any distance, if the transmission is in neutral. To place the euro twin clutch transmission in neu- tral, follow the procedure belo...

  • Page 313: Contents

    What to do in emergencies contents ! Hazard warning flashers . . . . . . . . . . .313 ! If your engine overheats . . . . . . . . . . . .313 ! Wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .314 ▫ torque specifications . . . . . . . . . . . . . . . . . . .315 ! Tire se...

  • Page 314

    ! Freeing a stuck vehicle . . . . . . . . . . . . .341 ! Shift lever override . . . . . . . . . . . . . . . .342 ! Towing a disabled vehicle . . . . . . . . . . .343 ▫ manual transmission . . . . . . . . . . . . . . . . . . .344 ▫ euro twin clutch transmission. . . . . . . . . . . .344 ▫ automatic t...

  • Page 315

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the radio. Push the switch to turn on the hazard warning flashers. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the ...

  • Page 316

    Caution! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the h (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle. Turn off the air conditioning and wait until the pointer drops back into the n...

  • Page 317

    Torque specifications lug nut/bolt torque **lug nut/ bolt size lug nut/ bolt socket size 63 ft-lbs (86 n·m) steel wheels only 89 ft-lbs (120 n·m) aluminum wheels only m12 x 1.25 17 mm **use only your authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening. ...

  • Page 318

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten...

  • Page 319

    Tire service kit — if equipped small punctures up to 1/4” (6 mm) in the tire tread can be sealed with tire service kit. Foreign objects (e.G., screws or nails) should not be removed from the tire. Tire service kit can be used in outside temperatures down to approxi- mately -4°f (-20°c). This kit wil...

  • Page 320

    Using the mode select knob and hoses your tire service kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black air pump hose (7) when selecting this mode. ...

  • Page 321

    Tire service kit usage precautions • replace the tire service kit sealant bottle (1) and sealant hose (6) prior to the expiration date (printed at the lower right hand corner on the bottle label) to assure optimum operation of the system. Refer to “sealing a tire with tire service kit” section (f) “...

  • Page 322

    • when the tire service kit sealant is in a liquid form, clean water, and a damp cloth will remove the material from the vehicle or tire and wheel components. Once the sealant dries, it can easily be peeled off and properly discarded. • for optimum performance, make sure the valve stem on the wheel ...

  • Page 323

    Warning! (continued) – if you are unsure of the condition of the tire or the wheel. • keep tire service kit away from open flames or heat source. • a loose tire service kit thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the tire service kit in the...

  • Page 324

    Sealing a tire with tire service kit (a) whenever you stop to use tire service kit: 1. Pull over to a safe location and turn on the vehicle’s hazard warning flashers. 2. Verify that the valve stem (on the wheel with the deflated tire) is in a position that is near to the ground. This will allow the ...

  • Page 325

    (c) injecting tire service kit sealant into the deflated tire: • always start the engine before turning on the tire service kit. Note: manual transmission vehicles must have the parking brake engaged and the shift lever in neutral. • after pushing the power button (4), the sealant (white fluid) will...

  • Page 326

    If the sealant (white fluid) does flow through the sealant hose (6): 1. Continue to operate the pump until sealant is no longer flowing through hose (typically takes 30 - 70 seconds). As the sealant flows through the sealant hose (6), the pressure gauge (3) can read as high as 70 psi (4.8 bar). The ...

  • Page 327

    3. Immediately disconnect the sealant hose (6) from the valve stem, reinstall the cap on the fitting at the end of the hose, and place the tire service kit in the vehicle storage location. Quickly proceed to (d) “drive ve- hicle.” caution! • the metal end fitting from power plug (8) may get hot afte...

  • Page 328

    (e) after driving: pull over to a safe location. Refer to “whenever you stop to use tire service kit” before continuing. 1. Push in the mode select knob (5) and turn to the air mode position. 2. Uncoil the power plug and insert the plug into the vehicle’s 12 volt power outlet. 3. Uncoil the air pump...

  • Page 329

    5. Remove the speed limit sticker from the instrument panel after the tire has been repaired. 6. Replace the sealant bottle (1) and sealant hose (6) assembly at your authorized dealer as soon as pos- sible. Refer to (f) “sealant bottle and hose replace- ment”. Note: when having the tire serviced, ad...

  • Page 330

    Jacking and tire changing — if equipped warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehi...

  • Page 331

    Spare tire removal the spare tire is stowed in underneath the rear cargo area on the outside of the car. 1. Remove the cargo floor to access the winch. Jack location 1 — emergency fuel fill funnel 2 — jack 3 — jack handle 4 — emergency allen key 5 — emergency spare tire bag 6 — emergency screwdriver...

  • Page 332

    2. Remove the jack handle and use the wrench end to lower the spare tire. 3. When the spare is clear, replace the jack tools. Preparations for jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle clos...

  • Page 333

    4. Place the shift lever in park (euro twin clutch transmission) or reverse (manual transmission). 5. Turn off the ignition. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. Note: pass...

  • Page 334

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 335

    Note: there are front and rear jacking locations on each side of the body (as indicated by the traingular lift point symbols on the sill molding). Front jacking location rear jacking location 6 what to do in emergencies 333.

  • Page 336

    4. Place the jack underneath the lift area that is closest to the flat tire. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, centering the jack saddle between the locating notches on the sill flange. 5. Raise the vehicle just enough to remove the...

  • Page 337

    Warning! • to avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. • to avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp...

  • Page 338

    Spare tire stowage rotate the jack wrench tool on the winch drive nut clockwise (the flat tire must not be connected to the winch) until effort becomes heavy and an audible click is heard indicating the winch is properly stowed. Cover the flat tire with the emergency spare tire bag and stow the flat...

  • Page 339

    Preparations for jump-start the battery in your vehicle is located on the drivers side of the engine compartment. Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove an...

  • Page 340

    3. Remove the protective cover over the remote positive (+) battery post. To remove the cover, pull upward on the cover. 4. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is off. Warning! Do not al...

  • Page 341

    Follow these steps to disconnect the negative (-) battery cable: 1. Pull outward on the negative (-) battery cable terminal release lever to the open position. 2. Lift up on the negative (-) battery cable terminal and set aside. Connecting the jumper cables 1. Connect the positive (+) end of the jum...

  • Page 342

    Disconnecting the jumper cables 1. Disconnect the negative (-) jumper cable from the negative (-) battery cable terminal of the vehicle with the discharged battery. 2. Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery. 3. Disconnect the po...

  • Page 343

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse (with automatic or euro twin clutch transmis...

  • Page 344

    Caution! (continued) • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no trans- mission shifting occurring). Warning! Fast spinning tires can be dangerous....

  • Page 345

    7. The vehicle may then be started in neutral. 8. Reinstall the shift lever boot. Towing a disabled vehicle note: this section describes procedures for towing a disabled vehicle using a commercial towing service. Proper towing or lifting equipment is required to prevent damage to your vehicle. Use o...

  • Page 346

    Caution! • do not use sling-type equipment when towing. Vehicle damage may occur. • when securing the vehicle to a flatbed truck, do not attach to front or rear suspension components. Dam- age to your vehicle may result from improper towing. If you must use the accessories (wipers, defroster, etc.) ...

  • Page 347

    Caution! • towing this vehicle in violation of the above re- quirements can cause severe transmission damage. Damage from improper towing is not covered un- der the new vehicle limited warranty. Automatic transmission • vehicle can be towed with the front wheels elevated. • vehicle can be towed on a...

  • Page 348

    Ignition key removal override this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock/ off (key removal) position. To remove the key manually, proceed as follows: 1. Firmly apply the parking brak...

  • Page 349

    7. Once the key is removed, reinstall the steering column cover. Caution! It is advisable to contact your authorized dealer to have the reinstall procedure carried out. If you would like to proceed in performing the reinstall procedure special attention must be paid to the correct coupling of the cl...

  • Page 351: Maintaining Your Vehicle

    Maintaining your vehicle contents ! Engine compartment — 1.4l turbo . . . .351 ! Onboard diagnostic system — obd ii . .352 ! Replacement parts . . . . . . . . . . . . . . . . . .352 ! Dealer service . . . . . . . . . . . . . . . . . . . . . .353 ! Maintenance procedures . . . . . . . . . . .353 ▫ en...

  • Page 352

    ▫ automatic transmission — aisin f21-250 hd transmission — if equipped . . . . . . . . . . . . .380 ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .382 ! Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .389 ▫ underhood fuses. . . ....

  • Page 353

    Engine compartment — 1.4l turbo 1 — air cleaner filter 4 — battery 7 — coolant pressure cap 2 — engine oil dipstick 5 — front distribution unit (fuses) 8 — coolant pressure bottle 3 — brake fluid reservoir 6 — washer fluid reservoir 9 — oil fill cap 7 maintaining your vehicle 351.

  • Page 354

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and euro twin clutch transmission control systems. When these sys- tems are operating properly, your vehicle will p...

  • Page 355

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 356

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, or air conditi...

  • Page 357

    Caution! Do not overfill the engine with oil. Overfilling the engine with oil will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This loss of oil pressure and increased oil temperature could damage your engine. Change engine oil the oil change indicat...

  • Page 358

    The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “engine compart- ment” in “maintaining your vehicle” for further informa- tion. Materials added to engine oil the manufacturer strongly recommends ag...

  • Page 359

    Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine comp...

  • Page 360

    Warning! (continued) an output greater than 12 volts. Do not allow cable clamps to touch each other. • battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after handling. • the battery in this vehicle has a vent hose that should not be disconnected and shoul...

  • Page 361

    Warning! • use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Re...

  • Page 362

    A/c air filter warning! Do not remove the a/c air filter while the blower is operating or personal injury may result. The a/c air filter is located in the fresh air inlet behind the glove box. Perform the following procedure to re- place the filter: 1. Open the glove compartment and remove all conte...

  • Page 363

    6. Remove the particulate air filters from the hvac air inlet housing. Pull the filter elements straight out of the housing. 7. Install the a/c air filter with the air filter position indicators pointing in the same direction as removal. A/c air filter access door open a/c air filter removal 7 maint...

  • Page 364

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 8. Rotate the glove compartment door back into position. Refer to the “maintenance schedule” for the prop...

  • Page 365

    Wiper blades clean the rubber edges of the wiper blades and the windshield and rear window periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt, waxes, or road film, and help reduce streaking and smearing. Operation of the wipers on dry glas...

  • Page 366

    To have a correct activation of strategy, the service position command (antipanic) must be active for at least half a second. At every valid activation of service position command, the wiper blades are activated for 250 ms. The service position command can be repeated several times to bring the blad...

  • Page 367

    4. Install the wiper blade and firmly push the wiper blade until it snaps into place. Rear wiper blade removal/installation 1. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 2. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin ...

  • Page 368

    3. Install the wiper blade pivot pin into the wiper blade holder at the end of the wiper arm, and firmly push the wiper blade until it snaps into place. Adding washer fluid the windshield washer fluid reservoir is located in the engine compartment, and the fluid level should be checked at regular in...

  • Page 369

    Exhaust system the best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle i...

  • Page 370

    Caution! • the catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine perfor- mance and cause serious damage to the engine. • damage to the catalytic converter can res...

  • Page 371

    To minimize the possibility of catalytic converter dam- age: • do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • do not try to start the engine by pushing or towing the vehicle. • do not idle the engine with any spark plug wires di...

  • Page 372

    Coolant checks check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- freeze). Check...

  • Page 373

    Caution! (continued) organic additive technology (oat) engine cool- ant is different and should not be mixed with hybrid organic additive technology (hoat) en- gine coolant (antifreeze) or any “globally compat- ible” coolant (antifreeze). If a non-oat engine coolant (antifreeze) is introduced into t...

  • Page 374

    Please review these recommendations for using organic additive technology (oat) engine coolant (antifreeze) that meets the requirements of fca material standard ms.90032. When adding engine coolant (antifreeze): • we recommend using mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic...

  • Page 375

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze) and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery tank. The cap should be inspected and cleaned if there is any accumulation of foreign materi...

  • Page 376

    Coolant level the coolant expansion bottle provides a quick visual method for determining that the coolant level is ad- equate. With the engine off and cold, the level of the engine coolant (antifreeze) in the bottle should be be- tween the “min” and “max” marks. As long as the engine operating temp...

  • Page 377

    • if frequent engine coolant (antifreeze) additions are required, the cooling system should be pressure tested for leaks. • maintain engine coolant (antifreeze) concentration at a minimum of 50% oat coolant (conforming to ms.90032) and distilled water for proper corrosion protection of your engine w...

  • Page 378

    Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. Fluid level can be expected to fall as the brake pads wear. The brake fluid level should be checked when the p...

  • Page 379

    Warning! (continued) cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or pro- longed braking, resulting in sudden brake failure. This could result in a col...

  • Page 380

    Fluid level check check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more than 3/16 inch (4.7 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level. Please see your authorized dealer for ser...

  • Page 381

    Special additives the manufacturer strongly recommends against using any special additives in the transmission. Transmission fluid is an engineered product and its performance may be impaired by supplemental addi- tives. Therefore, do not add any fluid additives to the transmission. The only excepti...

  • Page 382

    Fluid changes under normal operating conditions, the fluid installed at the factory will provide satisfactory lubrication for the life of the vehicle. However, if the vehicle is used for police, fleet, taxi, etc., change the fluid as indicated in the maintenance schedule. In addition, change the flu...

  • Page 383

    Special additives the manufacturer strongly recommends against using any special additives in the transmission. Automatic transmission fluid (atf) is an engineered product and its performance may be impaired by supple- mental additives. Therefore, do not add any fluid addi- tives to the transmission...

  • Page 384

    Fluid and filter changes under normal operating conditions, the fluid installed at the factory will provide satisfactory lubrication for the life of the vehicle. Routine fluid and filter changes are not required. However, change the fluid and filter if the fluid becomes contaminated (with water, etc...

  • Page 385

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar® car wash, or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover...

  • Page 386

    • if you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as...

  • Page 387

    Caution! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel’s protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel’s pro- tective finish. Only mopar® whee...

  • Page 388

    Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and mopar® total clean. ...

  • Page 389

    Cleaning headlights your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses ...

  • Page 390

    Instrument panel bezels caution! When installing hanging air fresheners in your ve- hicle, read the installation instructions carefully. Some air fresheners will damage the finish of painted or decorated parts if allowed to directly contact any surface. Cleaning plastic instrument cluster lenses the...

  • Page 391

    Warning! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced a...

  • Page 392

    Underhood fuses the front distribution unit is located on the right side of the engine compartment, next to the battery. To access the fuses, press the release tabs and remove the cover. The id number of the electrical component correspond- ing to each fuse can be found on the back of the cover. Fro...

  • Page 393

    Cavity maxi fuse mini fuse description f01 60 amp blue – body controller f02 60 amp blue – body controller rear distribution unit f03 20 amp yellow – ignition switch f04 40 amp orange – anti-lock brake pump f05 70 amp tan – electric power steering f06 30 amp green – radiator fan - low speed f07 50 a...

  • Page 394

    Cavity maxi fuse mini fuse description f18 – 5 amp tan powertrain (multiair – if equipped) f19 – 7.5 amp brown air conditioning f20 – 30 amp green rear defroster f21 – 15 amp blue fuel pump f23 – 20 amp yellow anti-lock brake valves f24 – 7.5 amp brown stability control system f30 – 5 amp tan after ...

  • Page 395

    Interior fuses the interior fuse panel is part of the body control module (bcm) and is located on the driver’s side under the instrument panel. Rear interior fuses the rear interior fuse panel is located on the driver’s side in the rear compartment. Interior fuse panel rear fuse panel 7 maintaining ...

  • Page 396

    Vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • disconnect the negative cable from the battery. • anytime you store your vehicle, or keep it out of service (e.G., vacation) for two weeks or more, run the air c...

  • Page 397

    Exterior bulbs bulb number front low and high beam headlamp hir2ll front turn signal lamps wy21w front parking/daytime running lamps w21/5w front side marker lamps led (see authorized dealer) rear tail/stop lamps p21/5w rear tail lamp led (see authorized dealer) rear turn signal lamps p21w rear back...

  • Page 398

    Bulb number license plate lamps w5w note: numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your authorized dealer or refer to the applicable service manual. Bulb replacement note: lens fogging can occur under certain atmo...

  • Page 399

    2. Rotate the bulb counter-clockwise. 3. Remove the bulb when all the tabs are aligned with the openings in the metal holder. 4. Disconnect the electrical connector from the bulb. Bulb removal procedure electrical connector removal 7 maintaining your vehicle 397.

  • Page 400

    5. Install the new bulb and rotate clockwise to lock in place. 6. Reinstall the plastic cap. New bulb installation headlamp sealing cap installation 398 maintaining your vehicle.

  • Page 401

    Front turn signal, parking and daytime running lamps 1. Turn front wheels inboard to access upper cover in wheel liner. 2. Open the upper cover on the front of the wheel liner. 3. Remove the cap from the back of the lower headlamp housing. 4. Rotate the bulb counter clockwise and remove. 5. Install ...

  • Page 402

    5. Remove the two screws that secure the backplate to the tail lamp housing. 6. Separate the backplate from the tail lamp housing. 7. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise. 8. Remove the backup lamp bulb by pulling straight out. 9. Replace...

  • Page 403

    Fluids, lubricants, and genuine parts engine component fluid, lubricant, or genuine part engine coolant – 1.4l turbo engine we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) or equivalent meeting the requirements of chrysler material standa...

  • Page 404

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 405

    Chassis component fluid, lubricant, or genuine part manual transmission – if equipped we recommend you use mopar® c series manual & dual dry clutch transmission fluid euro twin clutch transmission – if equipped gear oil: use only mopar® c series manual & dual dry clutch transmission fluid or equival...

  • Page 407: Maintenance Schedules

    Maintenance schedules contents ! Maintenance schedule . . . . . . . . . . . . . .406 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .408 8.

  • Page 408

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate in th...

  • Page 409

    Once a month or before a long trip: • check engine oil level. • check windshield washer fluid level. • check the tire inflation pressures and look for unusual wear or damage. • check the fluid levels of the coolant reservoir, and brake master cylinder reservoir, and fill as needed. • check function ...

  • Page 410

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,0...

  • Page 411

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 412

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 413

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000...

  • Page 414

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 415: Contents

    If you need consumer assistance contents ! Suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .415 ▫ prepare for the appointment. . . . . . . . . . . . .415 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .415 ▫ be reasonable with requests ....

  • Page 416

    ! Department of transportation uniform tire quality grades . . . . . . . .420 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .421 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .421 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .421 414 if you need consumer...

  • Page 417

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 418

    Warranty service must be done by an authorized dealer. We strongly recommend that you take the vehicle to an authorized dealer. They know your vehicle the best, and are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trai...

  • Page 419

    Customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has installed special tdd (telecommuni- cation devices for the deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a tdd...

  • Page 420

    We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You will be pleased with their sincere efforts to re...

  • Page 421

    To contact nhtsa, you may either call the auto safety hotline toll free at 1-888-327-4236 (tty: 1-800-424- 9153), or go to http://www.Safercar.Gov; or write to: adminis- trator, nhtsa, 1200 new jersey avenue, se., west building, washington, d.C. 20590. You can also obtain other information about mot...

  • Page 422

    Diagnostic procedure manuals diagnostic procedure manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and cor...

  • Page 423

    Treadwear the treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relativ...

  • Page 424

    The grade c corresponds to a level of performance, which all passenger car tires must meet under the federal motor vehicle safety standard no. 109. Grades b and a represent higher levels of performance on the laboratory test wheel, than the minimum required by law. Warning! The temperature grade for...

  • Page 425: Index

    Index 10

  • Page 426

    Adding engine coolant (antifreeze) . . . . . . . . . . . .371 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .306 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .366 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .304 air bag . . . . . . . . ....

  • Page 427

    Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253 fluid and filter changes . . . . . . . . . . . . . . . . . .382 fluid change . . . . . . . . . . . . . . . . . . . . . . . . . .382 fluid level check . . . . . . . . . . . . . . . . . . . . . . .381 fluid type . . . . . . . . . ....

  • Page 428

    Chains, tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .294 changing a flat tire . . . . . . . . . . . . . . . . . . . . . . .328 chart, tire sizing . . . . . . . . . . . . . . . . . . . . . . . . .271 check engine light (malfunction indicator light) . .169 checking your vehicle for sa...

  • Page 429

    Coolant level . . . . . . . . . . . . . . . . . . . . . .370, 374 disposal of used coolant . . . . . . . . . . . . . . . . .373 drain, flush, and refill . . . . . . . . . . . . . . . . . . .370 inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .374 points to remember . . . . . . . . ....

  • Page 430

    Electronic vehicle information center (evic) . .135, 180 exit trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .185 start of trip procedure . . . . . . . . . . . . . . . . . . .185 emergency deck lid release . . . . . . . . . . . . . . . . . .29 emergency, in case of hazard warning fla...

  • Page 431

    Filler location fuel . . . . . . . . . . . . . . . . . . . . . . . .169 filters air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .356 air conditioning . . . . . . . . . . . . . . . . . . . . . . .360 engine fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .401 engine oil . . ....

  • Page 432

    Gasoline (fuel). . . . . . . . . . . . . . . . . . . . . . . .302, 400 gasoline, reformulated . . . . . . . . . . . . . . . . . . . . .303 gauges coolant temperature . . . . . . . . . . . . . . . . . . . . .169 fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 odometer . . . ...

  • Page 433

    Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 jacking instructions. . . . . . . . . . . . . . . . . . . . . . . .331 jack location . . . . . . . . . . . . . . . . . . . . . . . . . . . .328 jack operation . . . . . . . . . . . . . . . . . . . . . . . .328, 331 jump starti...

  • Page 434

    Security alarm . . . . . . . . . . . . . . . . . . . . . . . . . .15 service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .396 service engine soon (malfunction indicator) . . . .169 tire pressure monitoring (tpms) . . . . . . . . . . . .169 traction control . . . . . . . . . . . . . ....

  • Page 435

    New vehicle break-in period . . . . . . . . . . . . . . . . . .82 occupant restraints . . . . . . . . . . . . . . . . . . . . . . . .31 octane rating, gasoline (fuel) . . . . . . . . . . . . . . . .302 odometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169 trip . . . . . . . . . . ...

  • Page 436

    Pregnant women and seat belts . . . . . . . . . . . . . . . .40 preparation for jacking . . . . . . . . . . . . . . . . . . . . .330 pretensioners seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 radial ply tires . . . . . . . . . . . . . . . . . . . . . . . . . .284 radio op...

  • Page 437

    Lap/shoulder belts . . . . . . . . . . . . . . . . . . . . . . .35 lap/shoulder belt untwisting . . . . . . . . . . . . . . .40 pregnant women . . . . . . . . . . . . . . . . . . . . . . . .40 seat belt pretensioner . . . . . . . . . . . . . . . . . . . . .41 seat belt reminder . . . . . . . . . . ....

  • Page 438

    Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .229 automatic transmission . . . . . . . . . . . . . . . . . .229 cold weather . . . . . . . . . . . . . . . . . . . . . . . . . .230 engine fails to start . . . . . . . . . . . . . . . . . . . . .231 euro twin clutch transmissi...

  • Page 439

    Pressure warning light . . . . . . . . . . . . . . . . . . .169 quality grading . . . . . . . . . . . . . . . . . . . . . . . .420 radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .284 replacement . . . . . . . . . . . . . . . . . . . . . . . . . . .292 rotation . . . . . . . . . ....

  • Page 440

    Unleaded gasoline . . . . . . . . . . . . . . . . . . . . . . . .302 untwisting procedure, seat belt . . . . . . . . . . . . . . . .40 vehicle identification number (vin) . . . . . . . . . . . . .7 vehicle loading . . . . . . . . . . . . . . . . . . . . . . . . . .277 vehicle modifications/alteratio...

  • Page 441

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 442

    O w n e r ’ s m a n u a l 2 0 1 5 2015 500l 15bf-126-ac third edition printed in u.S.A. 500l fca us llc.