Summary of 250S
Page 1
Www.G-lites.Com 1 user manual moving head model: 250s.
Page 2: Contents
Www.G-lites.Com 2 contents 1. - introduction 4 2. - safety instructions 4 3. - operating determination 6 4. - description of the device 7 4.1. – features 7 4.2. – overview 7 5. – installation 8 5.1. - installing/replacing the lamp 8 5.2. - lamp adjustment 9 5.3. – rigging 9 5.4. - dmx-512connection/...
Page 3: Important Terms:
Www.G-lites.Com 3 important terms: this manual covers important information about installation and operation of this moving head. Please read this manual carefully before installing and operating this moving head. Follow the safety precautions listed below: a. Read this manual carefully and keep man...
Page 4: 250S
Www.G-lites.Com 4 250s 1 ． introduction thank you for having chosen this moving head light .You will see you have acquired a powerful and versatile device. Unpack your moving-head light. Before you initial start-up, please make sure that there is no damage caused by transportation. Should there be a...
Page 5
Www.G-lites.Com 5 make sure that the available voltage is not higher than stated on the rear panel. Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-cord from time to time. Always disconnect from the mains, when the device is not in use or befo...
Page 6
Www.G-lites.Com 6 3 ． operating determinations this device is a moving-head spot for creating decorative effects. This product is only allowed to be operated with an alternating current of 230v, 50hz and was designed for indoor use only. This device is designed for professional use, e.G. On stages, ...
Page 7
Www.G-lites.Com 7 etc. 4 ． description of the device 4 ． 1 features powerful moving-head versatile moving-head with a wide range of illumination and decoration possibilities. 9 brilliant, dichroic colors plus white. 7 static metal gobos plus open. Auto focus. Strobe-effect with 1-7 flashes per secon...
Page 8
Www.G-lites.Com 8 5 、 installation 5 ． 1 installing/replacing the lamp danger to life! Only install the lamp with the device switched off! Unplug from mains before! For the installation, you need one hsd250/msd250 lamp. Protection gloves, helmet with sight, leather apron caution! The lamp has to be ...
Page 9
Www.G-lites.Com 9 do not operate this device with opened cover! 5 ． 2 lamp adjustment the lamp holder is aligned at the factory. Due to differences between lamps, fine adjustment may improve light performance. Strike the lamp, open the shutter and the iris, set the dimmer intensity onto 100% and foc...
Page 10
Www.G-lites.Com 10 the main attachment fails. When rigging, un-rigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden. The operator has to make sure that safety-relating and machine-technical in...
Page 11
Www.G-lites.Com 11 make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixture is secure. The moving head can be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics (see th...
Page 12
Www.G-lites.Com 12 5 ． 4 dmx-512 connection/connection between fixtures the wires must not come into contact with each other; otherwise the fixtures will not work at all, or will not work properly. Only use a stereo shielded cable and 3-pin xlr-plugs and connectors in order to connect the controller...
Page 13
Www.G-lites.Com 13 caution: at the last fixture, the dmx-cable has to be terminated with a terminator. Solder a 120 resistor between signal (“c”) and signal (+) into a 3-pin xlr-plug and plug it in the dmx- output of the last fixture. 5 ． 5 connection with the mains connect the device to the mains w...
Page 14
Www.G-lites.Com 14 occupation of the dip-switches (8-bit-mode): setting the dmx starting address: dip-switch no. 1 2 3 4 5 6 7 8 9 projector number & channels dmx-starting address: 1 2 4 8 16 32 64 128 256 device 1-channels 1-8 on off device 2-channels 9-16 on off device 3-channels 17-24 on off devi...
Page 15
Www.G-lites.Com 15 6.2 dmx control channels channel 1: 9colors+open white + rotating, adjustable speed strobe effect channel 2: 7gobos clockwise and counter clockwise, adjustable speed channel 3: 7gobos+open white channel 4: strobe effect 1~7fps+dimmer channel 5: pan movement (within 450 ℃ ) channel...
Page 16
Www.G-lites.Com 16 7 、 cleaning and maintenance the operator has to make sure that safety-relating and machine-technical installations are inspected by an expert after every four years in the course of an acceptance test. The operator has to make sure that safety-relating and machine-technical insta...
Page 17
Www.G-lites.Com 17 7 ． 1 replacing the fuse if the lamp burns out, the fine-wire fuse of the device might fuse, too. Only replace the fuse by a fuse of same type and rating. Before replacing the fuse, unplug mains lead. Procedure: step 1: unscrew the fuse holder on the rear panel with a fitting scre...
Page 18: Technical Data
Www.G-lites.Com 18 technical data lamp yembo: 250 w/hs (courtesy lamp included) osram: hsd 250 (6000 k) hsd 250/80 (8000 k) colour 8 colors, achieving high speed double way rainbow and scrolling effect, pattern internal light rotating function, freely adjusting fast, low speed, clockwise and anticlo...
Page 19
Www.G-lites.Com 19 power magnetic ballast 200-220 v – 60 hz 100-120 v – 60 hz (optional) 220-240 v – 50 hz (optional) power power consumption: 400 w dimension l 420 w 390 h 560 mm l 16.53 w 15.35 h 22.05 inches weight 23 kg.
Page 20: General Troubleshooting
Www.G-lites.Com 20 general troubleshooting this chapter provides information on diagnosing and solving operational problems. If a solution to your problem cannot be found in the following subsections, contact your authorized dealer or led-g technical support. Unit functions but lamp does not strike ...