Gb730 installation tool gage bilt made in u.S.A. Gage bilt inc. 44766 centre court (586) 226-1500 clinton twp. Mi 48038 (586) 226-1505 fax e-mail: solutions@gagebilt.Com / www.Gagebilt.Com gage bilt tools are available worldwide e-mail us for a distributor near you. S/n: 2317 and above please contac...
2 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. Specifications hand held weight - 4.70 lbs. (2.1 kg) air pressure req'd - 90-100 p.S.I. (6.2-6.9 bar) air consumption - .16 scf/cycle (4.53 l/cycle) hydraulic oil - automatic transmission oil, dexron iii, or equiv...
3 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. Warning do not pull fastener unless it is placed in an assembly, pin will eject forcibly when pintail breaks off. Severe personal injury may result. Warning do not operate without stat-o-seal (s572) and cap screws...
4 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. Image may not reflect actual tool principle of operation when the actuator lever assy is depressed, the pressurized air inside the tool is released allowing spring pressure to move the valve spool assy, causing th...
5 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. How to use the gb730 warning: operator must read and understand all warnings and cautions. Warning: it is required that eye protection and hearing protection be worn during operation. Warning: do not pull rivet in...
6 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. Description covered under patent no. 5,485,727 warning : the balance of this tool is designed for horizontal use and is not ergonomically best suited for all applications. Gage bilt will be pleased to advise for y...
7 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. Filling and bleeding instructions warning: do not cycle tool without air bleeder, or the screw and stat-o-seal, installed in tool head. Severe personal injury may result. Caution: before filling handle, air piston...
8 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. Troubleshooting providing all maintenance conditions have been met, follow this systematic approach to diagnosis. 1. More than one pull is required to break rivet. A) tool needs to be bled. (see filling and bleedi...
9 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. Overhaul warning : disconnect tool from its air source before performing overhaul. Warning : tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any r...
10 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. Warning: this tool incorporates a patented hydraulic relief valve. When overhauling tool, o’ring (s829), back-up ring (401084), retaining ring (400935) and spring (50806) must be replaced. Failure to do so could ...
11 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. Handle to inspect air cylinder bore, remove base cover (704125). Any further disassembly will require removal of the head cylinder assy (730398) first. For complete disassembly, start by removing base cover (7041...
12 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. First aid measures eye: no specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. Skin: no specific first aid measures are required. As a precaution,...
13 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. Gb730- selection chart gage bilt also supplies pin & collar swage inspection gages to certify correct swage installation. Fastener dia. Right angle 1 3/32 3a-352b-25 3a-751b-54ra 1/8 4a-752c-20 4a-752c-45 4a-751b...
14 rev. 2/15 s/n: 2317 and above please contact gage bilt for all other serial numbers. Dexron® is a registered trademark of general motors corporation. Lubriplate® is a registered trademark of fiske brothers refining. Loctite® is a registered trademark of henkel corporation. Seller warrants that al...
