Gb730 installation tool gage bilt made in u.S.A. Gage bilt inc. 44766 centre court (586) 226-1500 clinton twp. Mi 48038 (586) 226-1505 fax e-mail: solutions@gagebilt.Com / www.Gagebilt.Com gage bilt tools are available worldwide e-mail us for a distributor near you..
2 rev. 9/11 specifications hand held weight - 4.70 lbs. Air pressure req'd - 90-100 p.S.I. Air consumption - .16 scf/cycle (4.53 l/cycle) hydraulic fluid - automatic transmission fluid, dexron iii, or equivalent. Setting stroke - .500" rated pull load - 4,000 lbs. Noise level - 81.5 db (a) vibration...
3 rev. 9/11 warning do not pull fastener unless it is placed in an assembly, pin will eject forcibly when pintail breaks off. Severe personal injury may result. Warning do not operate without stat-o-seal (s572) and cap screw (402482). Pressurized hydraulic fluid may cause severe personal injury. War...
4 rev. 9/11 image may not reflect actual tool principle of operation when the trigger is depressed, the pressurized air inside the tool is released allowing spring pressure to move the valve spool, causing the air to be redirected. The air is directed to the top side of the air piston, moving it in ...
5 rev. 9/11 how to use the gb730 warning: operator must read and understand all warnings and cautions. Warning: it is recommended that eye protection and hearing protection be worn during operation. Warning: do not pull rivet in the air. Personal injury from fastener ejecting may occur. Warning: air...
6 rev. 9/11 description covered under patent no. 5,485,727 warning : the balance of this tool is designed for horizontal use and is not ergonomically best suited for all applications. Gage bilt will be pleased to advise for your specific application. The gb730 is a pneumatic-hydraulic tool designed ...
7 rev. 9/11 filling and bleeding instructions warning: do not cycle tool without air bleeder, or the screw and stat-o-seal, installed in tool head. Severe personal injury may result. Caution: before filling handle, air piston should be all the way down. Caution: when forcing piston rod assembly down...
8 rev. 9/11 704214 stem catcher bag 730151 piston rod wrench 704151 power cylinder tool 704152 seal guide 704150 packing plug wrench part no. Description 730151 piston rod wrench 704150 packing plug wrench assembly 704151 power cylinder tool 704152 seal guide s1178 valve extractor (not shown) 704162...
9 rev. 9/11 head remove nose assembly from tool before attempting disassembly of head assembly. Remove end cap (730717). Push against threaded end of head piston (730311) to slide it out of head cylinder (730398). Be careful not to damage threads or cause burrs on polished piston rod surface. Warnin...
10 rev. 9/11 handle to inspect air cylinder bore, remove base cover (704125). Any further disassembly will require removal of the head cylinder ass’y (730398) first. For complete disassembly, start by removing base cover (704125). Next, holding tool upright, remove four button-head cap screws (a-928...
11 rev. 9/11 first aid skin: wash thoroughly with soap and water as soon as possible. Casual contact requires no immediate attention. If irritation develops, consult a physician. Ingestion: seek medical attention immediately. Do not induce vomiting. Eyes: flush with copious amounts of water. If irri...
12 rev. 9/11 gb730- selection chart gage bilt also supplies pin & collar swage inspection gages to certify correct swage installation. Fastener dia. Right angle 1 3/32 3a-352b-25 3a-751b-54ra 1/8 4a-752b-20 4a-752b-45 4a-751b-54ra 4a-752a-43os 5/32 5a-752b-20 5a-752b-45 5a-751b-54ra 5a-752a-43os 3/1...
13 rev. 9/11 declaration of conformity we declare that the equipment specified herein conforms to the following standards and directives. En12100-1 & en12100-2 en13849 en792-1:2000+a1 council directive: machine directive 2006/42/ec equipment description: gbp700 series fastener installation tools man...
